Safety Instructions And General Warnings - YASKAWA CIMR-AC2B0004 Quick Start Manual

1 Safety Instructions and General Warnings

1 Safety Instructions and General Warnings
YASKAWA Electric supplies component parts for use in a wide variety of industrial applications. The selection and
application of YASKAWA products remain the responsibility of the equipment designer or end user. YASKAWA accepts
no responsibility for the way its products are incorporated into the final system design. Under no circumstances should
any YASKAWA product be incorporated into any product or design as the exclusive or sole safety control. Without
exception, all controls should be designed to detect faults dynamically and fail safely under all circumstances. All
products designed to incorporate a component part manufactured by YASKAWA must be supplied to the end user with
appropriate warnings and instructions as to the safe use and operation of that part. Any warnings provided by
YASKAWA must be promptly provided to the end user. YASKAWA offers an express warranty only as to the quality of
its products in conforming to standards and specifications published in the manual. NO OTHER WARRANTY,
EXPRESS OR IMPLIED, IS OFFERED. YASKAWA assumes no liability for any personal injury, property damage,
losses, or claims arising from misapplication of its products.
Applicable Documentation
The following manuals are available for A1000 series drives with 1000Hz software:
ALM
DIGITAL OPERATOR JVOP-180
F1 F2
LO
ESC
RE
RESET ENTER
RUN STOP
CIMR-AA2A0021FAA
200V 3Phase 5.5kW/3.7kW
S/N:
WARNING AVERTISSMENT NPJT31470-1
Risk of electric shock. Risque de décharge électrique.
● Read manual before installing. ● Lire le manuel avant l'installation.
● Wait 5 minutes for capacitor ● Attendre 5 minutes après la coupure
discharge after disconnecting de l'alimentation, pour permettre
power supply. la décharge des condensateurs.
To conform to requirements,
● ● Pour répondre aux exigences , s
make sure to ground the supply assurer que le neutre soit relié
neutral for 400V class. à la terre, pour la série 400V.
After opening the manual switch Après avoir déconnécte la protection
● between the drive and motor, ● entre le driver et le moteur, veuillez
please wait 5 minutes before
patienter 5 minutes avain d'effectuer
inspecting, performing une opération de montage ou de
maintenance or wiring the drive. câblage du variateur.
Hot surfaces Surfaces Chaudes
● Top and Side surfaces may ● Dessus et cotés du boitier Peuvent
become hot. Do not touch. devenir chaud. Ne Pas toucher.
危 険
けが．感電のおそれがあります。
● ● 据え付け、 運転の前には必ず取扱説明書を読むこと。
● 通電中および電源遮断後5分以内はフロントカバー
● を外さない事。
● 400V級インバータの場合は、電源の中性点が接地
● されていることを確認すること。( 対応）
● 保守・点検、配線を行う場合は、出力側開閉器を
● 遮断後5分待って実施してください。
高温注意
インバータ上部、両側面は高温になります。
●
● 触らないでください。
Receiving
Please perform the following tasks after receiving the drive:
• Inspect the drive for damage. If the drive appears damaged upon receipt, contact your supplier.
• Verify receipt of all components.
• Verify receipt of the correct model by checking the information on the nameplate. If you have received the wrong
model contact your supplier.
Drive Model Identification
A1000 Series drives with 1000Hz Software have the same model code as standard A1000 drives.
Nameplate
A1000 Series drives with 1000Hz Software are labeled with a special VAJ code on the nameplate. Also, the software
number shown on the nameplate must be "511 ".
EN 4
YASKAWA AC Drive A1000 Technical Manual
This manual provides detailed information on parameter settings, drive functions, and MEMOBUS/
Modbus specifications. Use this manual to expand drive functionality and to take advantage of
higher performance features.
YASKAWA AC Drive A1000 1000Hz Software Quick Start Guide (this book)
Read this manual first. This guide is packaged together with the product. It contains basic
information required to install and wire the drive, in addition to an overview of fault diagnostics,
maintenance, and parameter settings. Use the information in this book to prepare the drive for a trial
run with the application and for basic operation. Additionally parameter differences between 1000Hz
software and standard software are notified.
C I M R - A C 2
Drive A1000
No.
Series
B High Frequency
Region
No.
Code
C Europe
No. Voltage Class
3-phase, 200-240 Vac
2
4 3-phase, 380-480 Vac
0 0 0 4 F
B
Customized
Enclosure
No.
Specifications
Type
A IP00 Type
F
IP20 /
NEMA Type 1
Model Number
No.
A
YASKAWA ELECTRIC TOEP C710606 48A - AC Drive A1000 1000Hz Software - Quick Start Guide
A A
Design
Revision
Order
Environmental
Specification
Standard