Pulse REVSTER Owner's Manual
  1. Manuals
  2. Brands
  3. Pulse Manuals
  4. Scooter
  5. REVSTER
  6. Owner's manual

Pulse REVSTER Owner's Manual

Hide thumbs

Advertisement

Table of Contents

NOTE: TO OPERATE, PUSH START SCOOTER TO APPROXIMATELY 3
MPH WHILE TWISTING THROTTLE IN ORDER FOR MOTOR TO ENGAGE.
THE SCOOTER MUST BE ROLLING AT 3 MPH BEFORE THE MOTOR WILL
ENGAGE.
ELECTRIC SCOOTER
OWNER'S MANUAL
FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS
•
REVSTER
DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS?
CALL (866)-434-6067
05.06.16

Advertisement

Table of Contents
loading

Related Manuals for Pulse REVSTER

Summary of Contents for Pulse REVSTER

  • Page 1 MPH WHILE TWISTING THROTTLE IN ORDER FOR MOTOR TO ENGAGE. THE SCOOTER MUST BE ROLLING AT 3 MPH BEFORE THE MOTOR WILL ENGAGE. ELECTRIC SCOOTER OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS • REVSTER DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067...

  • Page 2: Table Of Contents

    Pulse Performance Products™ advises that you periodically review and reinforce all information in this manual with all riders, and that you inspect and maintain your scooter to insure their safety.

  • Page 3: Safety And Warnings

    Safety and Warnings Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the scooter. Never use near steps, water, or swimming pools. Keep your fingers and other body parts away from the chain, motor, steering system, wheels and all other moving components. Never ride while using a cell phone or wearing headphones.

  • Page 4: Before You Start

    5 mm hex wrench (not included) WARNING: DO NOT USE NON-PULSE PERFORMANCE PRODUCTS™ PRODUCTS WITH YOUR Altering of the original components may or may not be compatible with the design and will void the warranty. Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

  • Page 5: Assembly

    Assembly Handlebar Steer Tube Assembly Tools required: 5 mm hex wrench, 10 mm wrench 1. Depress the push button located on the 2. Tighten the bolts with the 5 mm hex 3. Align handlebars both vertically and rear of the fork and insert the handlebar wrench and 10 mm wrench.
  • Page 6 Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric scooter. Required components: battery charger • Initial battery charge time - 12 hours • Recharges after initial charge - up to 10 hours • When scooter is not in regular use batteries need to be charged on a monthly basis to maximize performance 1.

  • Page 7: Hardware Maintenance

    Hardware Maintenance Brake Check the brakes for proper function. When you step on the brake it should provide positive braking action. When you apply the brake with the speed control on, the brake cut off switch should stop the motor. Frame, Fork and Handlebars Check for cracks or broken connections.

  • Page 8: Repair And Maintenance

    Repair and Maintenance Chain and Rear Wheel Replacement Tools required: 4 mm hex wrench, 5 mm hex wrench, two [2] 13 mm wrenches, 10 mm wrench, phillips screwdriver 1. Using a 4 mm hex wrench remove the 2 2. Using two [2] 13 mm wrenches loosen the bolts from the rear chain cover on side of the rear wheel axle nuts.
  • Page 9 7. Reinstall chain cover with a 4 mm hex wrench. Do not over tighten bolts. WARNING: If you do not feel comfortable performing the adjustments, consult an authorized Pulse Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.
  • Page 10 Repair and Maintenance Front Wheel Replacement Tools required: Two 5mm hex wrenches 1. Using two 5 mm hex wrenches loosen 2. Reinstall new replacement wheel 3. Reinstall hardware and tighten clockwise and remove the front axle by turning the ensuring to note the order and location of all with a 5 mm hex wrench.
  • Page 11 Repair and Maintenance Battery Charger Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ recommended battery charger. Wheels Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.

  • Page 12: Troubleshooting

    Battery may need to be replaced. Even with proper care, rechargeable batteries do not last forever. The average rechargeable battery life is 1 to 2 years depending on scooter conditions and use. Replace only with Pulse Performance Products™ replacement batteries. Scooter suddenly stops working.

  • Page 13: Scooter Components

    Scooter Components part description Frame Motor Front Fork Headset Clamp Kickstand Battery Box Deck Rear Wheel Chain Cover Front Wheel Chain Thumb Throttle Grip Controller Battery Steer Tube Handlebar Handlebar Clamp Charger Port Reset Button On/Off Switch Chain Wheel Guide Wheel Brake Cut-Off Switch Foot Brake...

  • Page 14: Warranty

    The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. Pulse Performance Products™ does not offer an extended warranty. If you have purchased an extended warranty, it must be honored by the store at which the scooter was purchased from.
  • Page 15 Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.
  • Page 16 Pulse Performance Products™ A Division of Bravo Sports™ 12801 Carmenita Rd. Santa Fe Springs, CA 90670 © 2012 Pulse Performance Products™ - All Rights Reserved...

Table of Contents