Advertisement
PARABODY
INC.
EXS00 BASE UNIT
PBFS01 ::
-
PRODUCT ASSEMBLY
INSTRUCTION SHEETS
TOOLS REQUIRED" FOR ASSEMBLY:
9/16
INC~ SOCKET
3/4 INCIt SOCKET
ADJUSTABLE
WRENCH
B.AMMER or
RUBBER MALLET
3/16
ALLEN WRENCH
5]32
ALLEN WRENCH
REVISION: ..W
¯ If you experience any problems with the assembly of this product, please contact
your dealer or your PARABODY
Customer Service reprcsentafive
at:
1-800-325-9714.
Advertisement
Table of Contents
Related Manuals for ParaBody PBF501
Summary of Contents for ParaBody PBF501
- Page 1 ADJUSTABLE B.AMMER or 3/16 ALLEN WRENCH 5]32 ALLEN WRENCH REVISION: ..W ¯ If you experience any problems with the assembly of this product, please contact your dealer or your PARABODY INC. PBFS01 :: WRENCH RUBBER MALLET Customer Service reprcsentafive 1-800-325-9714.
- Page 2 PBFS01 EXS00 BASE ~IT ASSEMBLY INSTRUCTIONS (STEP TIIE INSTRUCTIONS FOR STEP #I ARE TO BE USED WITH DRAWING SHEET #I OF 6. THE PARABODY EXS00 BASE UNIT M’L!ST BE ASSEMBLED ON A FLAT LEVF, L SURFACE TO ASSURE ITS PROPER FUNCTION.
- Page 3 PBFS0t EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (S~fEP #3) THE INSTRUCTIONS FOR STEP #,’3 Place each of the two (2) WEIGHT STACK BUMPERS over the GUIDE ROD HOLES (RADIUS EDGES FACING UP) on the WEIGHT STACK SUPPORT BASE. Insert RODS through the WEIGHT STACK BUMPERS and into the WEIGHT STACK SUPPOP.T BASE.
- Page 4 PBFb01 EXb00 BASE UNIT ASSEMBLY INSTRUCTIONS Insert one (1) 2 IN. SQ. END CAP into the BASE SEAT SUPPORT and carefully place it on its side the floor. Loosely assemble the BASE SEAT SUPPORT to the MAIN BACK SUPPORT, using two (2) "~ 1/4 BOLTS, four (4) 378 WASHERS, two (2) 3/8 LOCK WASHERS, and two (2) 3/8 Insert a 2 IN.
- Page 5 PBFS01 EXS00 ASSEIVI.BLY PARTS LIST FOR STEP COUNT ALL PARTS BEFORE BEGINNING ASSEIVIBLY HARDWARE:. ITEM NAME/DESCRIPTION i/2 X 3-1/2 LG. BOLT I/2 X 3 LG. BOLT 112 WASHER 1/2 LOCK WASHER ... :, ... 2 1/2 NUT 1/9_ LOW HEIGHT LOCI<...
- Page 6 PBFS01 E-X~0 ASSEMBLY PARTS LIST FOR STEP #2 COUNT ALL PARTS WELDMENTSfPARTS ITEM NAME/DESCRIPTION PRE STRETCH SLIDE ... ADJUSTABLE LEG CURL EXTENSION ADJUSTABLE PRE STRETCH SUPPORT ... ADJUSTABLE SEAT FRAME SEAT HANDLE ROLLER.PADS 16 IN. ROLLER PAD SHAFT ... 20 IN. ROLLER PAD SHAFT ...
- Page 7 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (~TEP #2) Insert two (2) 2 IN. SQ. END CAP into the TOP and BOTTOM ends of the LEG CUI~ EXTENSION. Securely assemble the LEG CURL EXTENSION onto the BASE SEAT SUPPORT, using one (1) I/2 .3 BOLT, and one (I) I/2 LOW HEIGHT LOC]:,I NUT.
- Page 8 PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (STIgP #2) THE INSTRUCTIONS FOP, STEP #2 ARE TO BE USED WITH DRAWING SHEET #2 & #3 OF 6. Securely assemble ~wo (2) 3/8 DIA. x 2 IN. BUSHING PULLEYS into the TOP BOO[V/SECTION and tl~ee (3) 318 DIA.
- Page 9 PBFS01 EXS00 BASE U-NIT ASSEMBLY INSTRUCTIONS (~,TEP #2) Attach eight (8) PARAGLIDE STRIPS to the ADJUSTABLE SEAT FRAME and the :BASE SEAT SUPPORT as shown in DETAIL A and B on the reverse side of the main assembly drawing for STEP #2, (SHEET #3 of 6), using the following steps: Thoroughly clean all inside and outside surfaces where the paraglide strips sre ::o be attached.
- Page 10 ¯ y PBFS0i EXS00 ASSEIViBL ’ PARTS LIST FOR STEP COUNT ALL PARTS BEFORE. BEGIIN-NING ASSEMBL HA~A~:. N~E~ESC~PTION ITE~ ~IGHT STACK BUMPE~ 3/8 ~. DIA. GUIDE ~OD ~S~ATO~ ~IGHT PLATE BUSH~OS ~/~ X 1-I/2 ~X ~AD BOLT ... 3l~ LOCK WAS~R 3/8 WAS~R 3/8 X 1-314 BOLT ...
- Page 11 PBFS01 EXS00 ASSEiVEBLY PARTS LIST FOR STEP #4 COUNT ALL PARTS BEFORE BEGINNING ASSEIVEBLY I-IAR_D ~rARE,:. ITEM NAME/DESCRIPTION 5/16 X I BOLT 3/8 X I-3/4 BOLT 5/16 WA SI-IEI~ 5/16 LOCK WASHER 3/8 LOCK WASHER 5/16 NUT ... 3/8 NUT ... LAT BAR HOOK COVER 1EN.
- Page 12 PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS iL~i~r ~.) TIIE INSTRUCTIONS FOP, STEP #4 A_~.E TO BE USED WITH DI%4.W~NG SI-~:ETS #S & #6 OF Assemble the SWIVEL PULLEY BRACKETS using (1) 3/8 Dia x 3/4 BOLT, (2) :511 5 WASHER, 3/8 WASHER and (1) 3/8 LOCKNUT (TIGHTEN TILL LOCKED THEN BACK[ NUT OFF 1/4 TURN).
- Page 13 RECOIVIIVIEiND CLEA2qfNG YOUR PROD:UCT (PADS AND ]FRAINI-E) ON REGULAR BASIS, USING x, VAl~f SOAPY WATER. ALSO, TOUCI:I-UP PAINT CAN BE PURCHASED FR~.)M YO OR PAI~3ODY DEALER, OR ]FROM YOUR PARABODY CUSTOMEK SERVICE Rv~PRESENTAT .IYE INSTRUCTIONS WARNING !t! WARNING !!!
- Page 15 DETA I L ~A" UNIT STEP ~ 1 SHEET ~ OF (~...
- Page 16 INSII3E £/]NNECTION Z. 5 .~ . E..N~ ~JIVEL PULLEY...
- Page 17 EXS’OD BASE UNIT ._STEP SH EET ?_ OF E,...
- Page 18 31’.4 bETA/L "N" ParaBody~ inc. RAMSEY, MINNESOTA "~ I STEP ~’ Ass"r, I..,,_,-~_.,~, I DI REVISIONS ¢_HAF’F LE.~, CURL EXTEN ¢,I~3N ROLLER PAD SLEEVE 1~.,,,,,,’-,* t’ PtSF501...
- Page 19 UNIT STEP #?_ CONT’D _SHEET S OF G,...
- Page 20 ~’. .’.
- Page 21 "~EE DE "bETA I L’E" ¯ .. ~ ..::’.’ ...,..:,,...~;. ¯ . :: : . .’..~ ...,... WFJ~iT ,’PLATE, C Z PER.. PLA’TE’~ ¯ ~TA C1¢. L :’~ DETAIL "F"...
- Page 24 PULLEY ~.AI~LE ROUTIN~ I?IAbRA/4...
- Page 25 o¢ DETAIL...