Panasonic PV-V4524S Operating Instructions Manual page 9

MTS Broadcast
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
VCR
R
L
VHF/UHF
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with a " " mark while the selected audio mode is indicated
with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language) and
Secondary Audio Program (sub language) broadcasts are being
received simultaneously. Select STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
• If stereo broadcast is weak and display flickers, select MONO
audio mode for possible better results.
SAP broadcast
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
MONO broadcast
Normal monaural sound broadcast.
®
Equipped with -TV Noise Reduction for true
MTS reproduction. ® -TV Noise Reduction is
required for good stereo separation and audio
fidelity. ® is a registered trademark, and is
licensed by ® Technology Licensing.
Stereo Amplifier
AUDIO OUT
R
R
L
AUDIO IN
R
L
OUT TO TV
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
- 4 -
VHS Hi-Fi Stereo System
Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2
STEREO
SAP
MONO
• Arrow indicates selection.
3
Make a recording.
See p. 5 of "Basic Operations" Instruction book.
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations" Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3
H I F I : L / R
H I F I : L
H I F I : R
NORMAL
CH 02
0 : 0 0 : 0 0
SP
• Arrow indicates
selection.
CH 02
0 : 0 0 : 0 0
SP
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
Standard stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a
stereo TV or an external stereo amp and speakers. (See page 4.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
CH 02
0 : 0 0 : 0 0
• Hi-Fi and normal audio playback volume level may differ.
SP
CH 02
0 : 0 0 : 0 0
SP
*Important: If a remote control button does not work when pressed,
Press SAP/ Hi-Fi repeatedly
to select desired mode.
• Refer to "Receivable
Broadcast Types" on page 4.
Press SAP/ Hi-Fi repeatedly
to select desired mode.
• Select "HIFI(L/R)" or "HIFI(L)"
or "HIFI(R)" to listen to stereo
recordings in stereo sound.
Select "NORMAL" for
monaural sound.
press the VCR button on the remote and try the button again.
- 5 -