General - Panasonic CQ-VD7200U Operating Instructions Manual

General

E
N
G
L
I
S Power
H
Turn your car's ignition key to ACC or ON position.
9
ON: press [MODE] (POWER) on the display unit.
Press [PWR] or [MODE] on the remote control.
OFF: press [MODE] (POWER) again for more than
2 seconds on the display unit.
Press [PWR] again or [MODE] again for more
than 2 seconds on the remote control.
[ ] (OPEN/CLOSE)
72 00 U
CQ -VD
[MODE] (POWER)
[MUTE]
[}] [{] (VOLUME)
[PWR]
(POWER)
[MODE]
[}] [{]
(VOLUME)
[MUTE]
18
CQ-VD7200U
Display Open/Close
OPEN: press [ ] (OPEN/CLOSE).
CLOSE: press [ ] (OPEN/CLOSE) again.
(After returning the lateral angle to the
neutral position.)
Notes:
¡When the display unit is opened or closed, a loud
beep sounds three times.
¡If the unit stops halfway, press [ ] (OPEN/CLOSE)
again and draw it all the way in.
¡Opening/closing the display can be done when the
power is off.
Warning: Do not touch the unit while the display
is moving. Inserting hands, fingers or foreign
objects into the unit can cause injuries and
damage to the unit.
Mode
Press [MODE] to change the mode.
TV VTR1
(a page 20) (a page 22)
CH-C
VTR2
(CD Changer Control)*
(a page 22)
(a page 36)
DVD/VCD(Video CD)/
AM/FM (Radio) CD/MP3
(a page 34) (a page 24, 28)
* Selectable only when a CD changer is connected.
Volume
[}] (VOLUME): up
[{] (VOLUME): down
Setting Range : 0 to 40
Note: The sound level for each source is stored in
memory.
Mute
MUTE ON: press [MUTE].
MUTE OFF: press [MUTE] again.
Loudness
When listening at low or medium volume,
enhance bass and treble tones.
LOUD ON: press and hold [MUTE] for more than 2
seconds.
LOUD OFF: press and hold [MUTE] for more than 2
seconds again.
Monitor Position Adjustment
Cautions:
¡For smooth adjustment, make sure to first return the lateral angle to the neutral position and then adjust the tilt angle.
¡Avoid physical shock on the monitor.
Tilt Angle/Front-Rear Position
[TILT]
1
Press and hold [TILT] on the display unit for more than 1 second.
2
Press [}], [{], []] or [[] to adjust.
The setup is the same way as the one from MENU. Refer to
"SET-UP : User Settings" for details.
Notes:
¡Vertical angle (TILT) and front-rear position data are saved in the memory, so
when the display unit is drawn out next, it is automatically set at the angle and
in the position adjusted before.
¡After adjusting its angle, also adjust the brightness to make it easy for you to
watch. (a
[}] [{] ¡The car model and installation condition may impose some restrictions on the
[] ] [[ ]
adjustment of the monitor's angle and position.
(Adjust)
Caution: Do not interfere with the movement of the monitor. Do not change
the position of the unit forcibly.
[}] [{]
[] ] [[ ] (Adjust)
Display Unit Lateral Angle Adjustment
Hold the display unit by the non-slip part on the upper half of it, and adjust its
lateral angle.
Caution: There is the danger of your fingers being pinched if you hold the
unit by the lower part. Hold the unit by the upper half, and move it carefully
without applying undue force.
Folding Down the Display Temporarily
Fold Down: press [TILT] on the display unit.
Raise: press [TILT] again on the display unit.
Note: Even when the unit is off, you can fold down the display temporarily.
Caution: Do not place any object on the display unit, or subject it to undue
force.
(a page 38)
page 44)
View from above
TILT
CQ-VD7200U
E
N
G
L
I
S
H
10
19