Memorex MVD2501 User Manual

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING:
Users of this product are cautioned not to make modifications or changes that are not
approved by MEM-CE, LLC., doing so may void the compliance of this product and may result in the
loss of the user's authority to operate the equipment.
DANGER:
This symbol is intended to alert the user to the risk of exposure to invisible and hazardous
laser radiation if the cover or back is opened the interlock fails or is defeated. Direct exposure to the
beam may damage your eyesight. DANGER: Invisible and hazardous laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
CAUTIONS:
• THIS DIGITAL VIDEO DISC PLAYER EMPLOYS A LASER SYSTEM.
• TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS OWNER`S MANUAL CAREFULLY AND
RETAIN FOR FUTURE REFERENCE.
• SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE PROVIDER.
• MISUSE OF CONTROLS, ADJUSTMENTS TO THE UNIT OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
• TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER
RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.
• DO NOT STARE INTO BEAM.
• WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power
surges ARE NOT covered under warranty for this product.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions source. This product should not be placed in a built-in
carefully. Please note that these are general precautions and installation such as a bookcase or rack unless proper
may not pertain to your unit. For example, this unit may not ventilation is provided or the manufacturer's instructions
have the capability to be connected to an outdoor antenna. have been adhered to.
1) Read these instructions. All the safety and operating 8) Do not install near any heat sources such as
instructions should be read before the product is operated. radiators, heat registers, stoves, or other apparatus
2) Keep these instructions. The safety and operating (including amplifiers) that produce heat.
instructions should be retained for future reference. 9) Do not defeat the safety purpose of the polarized
3) Heed all warnings. All warnings on the product and in or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
the operating instructions should be adhered to.
4) Follow all instructions. All operating and use type plug has two blades and a third grounding
instructions should be followed. prong. The wide blade or the third prong are
5) Do not use this apparatus near water. Do not use provided for your safety. If the provided plug does
this product near water and moisture, for example: near a not fit into your outlet, consult an electrician for
bathtub, washbowl, kitchen sink or laundry tub; in a wet replacement of the obsolete outlet.
basement; or near a swimming pool. 10) Protect the power cord from being walked on
6) Clean only with dry cloth. Unplug this product from the or pinched particularly at plugs, convenience
wall outlet before cleaning. Do not use liquid cleaners or receptacles, and the point where they exit from the
aerosol cleaners. Use a dry cloth for cleaning. apparatus.
7) Do not block any ventilation openings: Install in 11) Only use attachments/accessories specified by the
accordance with the manufacturers instructions. manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
Slots and openings in the cabinet and in the back or
bottom are provided for ventilation to ensure reliable table specified by the manufacturer, or sold with
operation of the product and to protect it from overheating. the apparatus. When a cart is used,
These openings must not be blocked or covered. The use caution when moving the cart/
openings should never be blocked by placing the product apparatus combination to avoid
on a bed, sofa, rug or other similar surface. This product injury from tip-over: An appliance
should never be placed near or over a radiator or heat and cart combination should be moved
DVD Player DVD Player Compact Compact
Let Me Entertain You
IMPORTANT SAFETY INSTRUCTIONS
with care. Quick stop, excessive force and uneven Code ANSI/NFPA 70 provides information with respect to
surfaces may cause the appliance and cart combination proper grounding of the mast and supporting structure,
to overturn. grounding of the lead-in wire to an antenna discharge
13) Unplug this apparatus during lightning storms or product, size of grounding conductors, location of
when unused for long periods of time. To protect antenna-discharge product, connection to grounding
your product from a lightning storm, or when it is left electrodes and requirements for the grounding electrodes.
unattended and unused for long periods of time, unplug it 20) Service: Do not attempt to service this product yourself as
from the wall outlet and disconnect the antenna or cable opening or removing covers may expose you to dangerous
system. This will prevent damage to the product due to voltage or other hazards. Refer all servicing to qualified
lightning and power-line surges. service personnel.
14) Refer all servicing to qualified service personnel. 21) Replacement parts: When replacement parts are
Servicing is required when the apparatus has been required, be sure the service technician uses replacement
damaged in any way, such as power-supply cord or parts specified by the manufacturer or those that have the
plug is damaged, liquid has been spilled or objects
same characteristics as the original parts. Unauthorized
have fallen into the apparatus, the apparatus has substitutions may result in fire or electric shock or other
been exposed to rain or moisture or does not hazards.
operate normally, or has been dropped. 22) Safety check: Upon completion of any service or repairs
15) Power source: This product should be operated only to this product, ask the service technician to perform
from the type of power source indicated on the marking safety checks to determine that the product is in proper
label. If you are not sure of the type of power supply to operating condition.
23) Wall or ceiling mounting: The product should be
your home, consult your appliance dealer or local power
company. For products intended to operate from battery mounted to a wall or ceiling only as recommended by
power, or other source, refer to the operation instructions. the manufacturer.
16) Power lines: An outside antenna system should not be 24) Damage requiring service: Unplug this product from
located in the vicinity of overhead power lines or other the wall outlet and refer service to qualified service
electric light or power circuits, or where it can fall into personnel under the following conditions.
such power lines or circuits. When installing an outside a) When the power-supply cord or plug is damaged.
antenna system, extreme care should be taken to keep b) If liquid has been spilled or objects have fallen into the
from touching such power lines or circuits as contact with product.
them might be fatal. c) If the product has been exposed to rain or water.
17) Overloading: Do not overload wall outlets and extension d) If the product does not operate normally by following the
cords as this can result in a risk of fire or electric shock. operating instructions. Adjust only those controls that are
18) Object and liquid entry: Never push objects of any kind
covered by the operating instructions, as an adjustment
into the product through openings as they may touch of other controls may result in damage and will require
dangerous voltage points or short out parts that could extensive work by a qualified technician to restore the
result in fire or electric shock. Never spill or spray any product to its normal operation.
type of liquid on the product. e) If the product has been dropped or the cabinet has been
19) Outdoor antenna grounding: If an outside antenna
damaged.
is connected f) When the product exhibits a distinct change in
to the product, performance-this indicates a need for service.
be sure the 25) Note to CATV system installer: This reminder is
antenna system provided to call the CATV system installer's attention to
is grounded so Article 820-40 of the NEC that provides guidelines for
as to provide proper grounding and, in particular, specifies that the
some protection cable ground shall be connected to the grounding system
against voltage of the building, as close to the point of cable entry as
surges and built practical.
up static charges. Section 810 of the National Electric
SAFETY PRECAUTIONS
NOTES ON HANDLING: NOTES ON MOISTURE CONDENSATION:
• When shipping the DVD player, always use the original Moisture condensation damages the DVD player. Please read
shipping carton and packing materials. For maximum the following carefully.
protection, repack the unit as it was originally packed at • Moisture condensation occurs, for example, when you
the factory. pour a cold drink into a glass on a warm day. Drops of
• Do not use volatile liquids, such as insect spray, near water form on the outside of the glass. In the same way,
the DVD player. Do not leave rubber or plastic products moisture may condense on the optical pick-up lens inside
in contact with the DVD player for a long time. They will this unit, one of the most crucial internal parts of the DVD
leave marks on the finish. player.
Moisture condensation occurs during the following cases:
• The top and rear panels of the DVD player may become
warm after a long period of use. This is normal and not a • When you bring the DVD player directly from a cold place
malfunction. to a warm place.
• When the DVD player is not in use, be sure to remove the • When you use the DVD player in a room where you just
disc and turn off the power. turned on the heater, or a place where the cold wind from
the air conditioner directly hits the unit.
NOTES ON LOCATING THE DVD PLAYER: • ln summer, when you use the DVD player in a hot and
• When you place this DVD player near a TV, radio or VCR, humid place just after you moved the unit from an air
the playback picture may become poor and the sound conditioned room.
may be distorted. In this case, move the DVD player away • When you use the DVD player in a humid place. Do not
from the TV, radio or VCR. use the DVD player where moisture condensation may
occur.
NOTES ON CLEANING:
• lf you use the DVD player in such a situation, it may
Use a soft, dry cloth for cleaning damage discs and internal parts. Remove the disc,
• For stubborn dirt, soak the cloth in a weak detergent connect the power cord of the DVD player to the wall
solution, wring well and wipe. Use a dry cloth to wipe it outlet, turn on the DVD player and leave it ON for two
dry. Do not use any type of solvent, such as thinner and or three hours. After two or three hours, the DVD player
benzene, as this may damage the surface of the DVD will have warmed up and evaporated any moisture. Keep
player. the DVD player connected to the wall outlet and moisture
• If you use a chemical-saturated cloth to clean the unit, condensation will seldom occur.
follow that product's instructions.
Warning: Cleaning and adjustment of lenses and /or other
components of playback mechanism should be performed by
a qualified service technician.
GETTING TO KNOW YOUR MEMOREX MVD2501
Congratulations on your purchase of the Memorex MVD2501 Compact DVD
Player. With this slim design progressive scan DVD player, connect to your
television for viewing of the most popular disc formats: DVD,CD-R/CD-RW,
DVD+R/RW, HDCD, JPEG or Kodak Picture CD. Use the full function remote
control to play, pause, stop, fast forward and rewind, plus an array of other
features.
Note: MVD2501 is not compatible with Blue Ray formatted discs.
®
LOCATION OF CONTROLS
u v w x
y U
W X
AC~120V/60Hz
1. Open/Close Button 5. Disc Compartment 8. Audio/Video Out
Jacks
2. Play/Pause Button 6. Remote Sensor
3. Stop Button 7. Power Indicator 9. AC Power Cord
4. Power Button
1. OPEN/CLOSE Button
2. 0–9, 10+ Button
3. MENU Button
17 17
1
4. ENTER Button
5. Navigation Buttons
6. Skip 9 Button
18 18
7. Search 7 Button
2
8. OSD (On Screen Display) Button
19 19
9. SUBTITLE Button
10. N/P (NTSC/PAL) Button
11. ANGLE Button
20 20 12. ZOOM Button
3
13. REPEAT Button
4
14. A-B Button
5
15. PROG Button
16. CLEAR Button
17. POWER Button
6
21 21
18. VOLUME +/– Buttons
22 22
7
19. MUTE Button
23 23
20. SETUP Button
24 24
8
21. Skip : Button
22. Search 8 Button
9 25 25
26 26
10
23. Play/Pause Button
WIDE RESET
11 27 27
24. TITLE Button
12 28 28
25. AUDIO Button
13 29 29
26. Stop Button
14 30 30
RANDOM GOTO
27. RESET Button
15 31 31
16 32 32
28. WIDE Button
29. STEP Button
30. SLOW Button
31. GOTO Button
32. RANDOM Button
REMOTE BATTERY INSTALLATION
REMOTE BATTERY INSTALLATION
1. Remove the Battery Compartment cover
by pushing in on the tab and then lifting the
cover off.
2. Install two (2) "AAA" batteries, paying
attention to the polarity diagram in the battery
compartment.
3. Replace the Battery Compartment cover.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed
battery may cause damage to the device.
4. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh
ones.
5. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible
battery leakage.
6. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer's
directions.)
7. Remove batteries promptly if consumed.
8. Clean the battery contacts and also those of the device prior to battery installation.
Please read these instructions completely
before operating this product.
SETTING UP THE MEMOREX MVD2501
AC CONNECTION
Insert the AC plug (with 2 blades) into a
conveniently located AC outlet rated at
120 V ~ 60Hz.
NOTE: The AC plug supplied with the unit is
polarized to help minimize the possibility of
electric shock. If the AC plug does not fit into a
non-polarized AC outlet, do not file or cut the
wide blade. It is the user's responsibility to have
an electrician replace the obsolete outlet.
V
REMOTE CONTROL OPERATIONAL RANGE
Point the remote control at the DVD player no more than 15 feet from the remote
control sensor and within and angle of 60°. The operating distance may vary
depending on the brightness of the room.
CONNECTIONS
Connecting via the Video Output Jacks (Cable Included)
AC~120V/60Hz
White
A/V cable
Red
Yellow
TO A/V IN JACKS
HOW TO USE THE MEMOREX MVD2501
BASIC OPERATION
The following operation is similar regardless of the type of disc used. For specific
instructions on how to use each disc type, see below and the other side of this guide.
Pause
Press the Play/Pause button while in the Play mode to pause. To resume
bm
normal playback, press the Play/Pause button bm.
Search
During playback, press the Search 7 or 8 button to move the disc forward
V bl
or backward at double (x2) speed to locate a specific section. Repeatedly press
AC~120V/60Hz
and the speed will increase to x4, x8, x16, x32 and resume normal playback. The
disc will move forward or backward at high speed until you press the Play/Pause
button bm; normal playback will resume at that point.
Note: This function is not available on all discs.
Skip
Press the Skip : button to advance the disc to the beginning of the next
bk
chapter/track. Press the Skip 9 button to move the disc to the beginning of the
U
previous chapter/track.
TO HDMI IN JACK
OSD (On Screen Display)
During playback, press the OSD button repeatedly to view the playback status
W
information.
Volume Adjustment
1. Press the Volume +/– buttons to adjust the volume. Note that the TV's volume
ar
must be turned up for these Volume/Mute buttons to operate properly.
2. Press the MUTE button to turn the sound off, the TV will display MUTE. Press
as
the MUTE button again or the Volume +/– buttons
as
RESET Button
With no disc inserted, press the RESET button to reset settings to their factory positions.
bq
MVD2501 DVD OPERATION
Playback of a DVD
1. Plug the AC cord into the outlet once the DVD player is connected to your TV.
2. Press the Power button to turn the DVD player on; the Power indicator will light
aq
green.
3. Press the OPEN/CLOSE button to open the disc tray. Insert a disc with the
u
label side facing up on the disc tray. Press the OPEN/CLOSE button
close the tray; playback will start automatically.
4. If the Menu appears, use the Navigation buttons
y
and press the ENTER button to select it.
x
5. To stop playback, press the STOP button bp. Because the unit will remember
where you stopped (not applicable in CD mode), simply press the Play/Pause
button to resume playback where you left off (resuming playback). If the STOP
bm
button is pressed twice, the unit will stop completely.
bp
User Guide
MEMOREX-CE.COM
MVD2501
AC Outlet
AC Plug
to cancel this function.
ar
again to
u
to select the desired option