Unit Dimensions Kes180; Kes180 Minimum Clearances - York KES180 Installation Instruction

®
B L O W E R M O T O R A N D D R I V E A C C E S S P A N E L
( A l w a y s o n t h e w i r i n g c o n n e c t i o n s i d e o f u n i t )
L o c a t e d o n o p p o s i t e s i d e O N L Y w h e n t h e b l o w e r
s e c t i o n h a s b e e n r o t a t e d 1 8 0
1 - 2 3 / 3 2 " K N O C K O U T
R e m o v e o n l y w h e n E l e c t r i c
H e a t A c c e s s o r y i s u s e d .
7 - 1 / 4
2 7 - 5 / 8
2 - 3 / 8 A I R
I N
2 - 3 / 1 6
5 6 - 3 / 8
* R e f e r t o I N S T A L L I N G R E F R I G E R A N T M A I N S i n i n s t a l l a t i o n i n s t r u c t i o n
w h e n p i p i n g t h r o u g h t h e o p p o s i t e s i d e o f t h e u n i t .
FIGURE 18 : UNIT DIMENSIONS KES180
TABLE 11: KES180 MINIMUM CLEARANCES
Side with RETURN AIR opening
Side with SUPPLY AIR opening
Side with PIPING CONNECTIONS
Side with access to both POWER & CONTROL WIRING
Bottom
1.
Overall dimensions of the unit will vary if an electric
heater, a supply air plenum or a base is used.
Unitary Products Group
7 / 8 " K N O C K O U T F O R P O W E R W I R I N G
D o n o t r e m o v e t h i s k n o c k o u t w h e n t h e u n i t i s e q u i p p e d w i t h a n E l e c t r i c
H e a t A c c e s s o r y . R e f e r t o d e t a i l o f t h e H e a t e r A c c e s s o r y f o r p o w e r
f r o m p o s i t i o n s h o w n .
w i r i n g a c c e s s o p e n i n g
7 / 8 " K N O C K O U T F O R
C O N T R O L W I R I N G
6 0 - 3 / 4
2 1 - 7 / 8
1 9 - 3 / 8
A I R
O U T
7 / 8
6
1 6 - 1 / 2
B L O W E R
S E C T I O N
C O I L
S E C T .
3 1 - 5 / 8
1
2 - 3 / 1 6
A L L D I M E N S I O N S A R E I N I N C H E S T H E Y
A R E S U B J E C T T O
N O T I C E . C E R T I F I E D D I M E N S I O N S W I L L
A L T E R N A T E
B E P R O V I D E D U P O N R E Q U E S T .
2 - 5 / 8 " K N O C K O U T *
5 - 7 / 8
2 - 1 / 8
5 - 1 / 2
1 8 - 7 / 8
3 2 - 3 / 8
A C C E S S O R I E S
E l e c t r i c H e a t e r s - A d d 1 4 - 1 / 4 " t o u n i t h e i g h t w h e n u s i n g
1 0 , 2 0 , 3 0 o r 5 0 k W
P l e n u m
B a s e A d d 2 4 " t o o v e r a l l u n i t h e i g h t w h e n u s e d .
6 2 - 5 / 8
F I L T E R A C C E S S P A N E L
F i l t e r s c a n b e r e m o v e d
t h r o u g h e i t h e r s i d e o f
t h e u n i t .
2.
This dimension is required for removal of the coil. Only
26" is required for normal service.
3.
If the coil has to be removed, this dimension is required
to loosen screws that secure the coil to the unit frame.
24"
This dimension will also be required for blower motor
1
24"
access if the piping connections are made on the oppo-
2
site side of the unit
61"
4.
Allow enough clearance to trap the condensate drain
3
-
line.
4
-
C H A N G E W I T H O U T
h e a t e r .
- A d d 2 7 " t o o v e r a l l u n i t h e i g h t w h e n u s e d .
Ø 2 "
5 - 1 1 / 1 6
8 - 1 / 2
4
Ø 2 "
9 - 1 / 2
1 2 - 7 / 8
2 - 9 / 1 6
Ø 1 - 3 / 8
2 - 9 / 1 6
550.13-N10Y
18