Enjoying Tv, Etc. With This Unit's Speakers; Adjusting The Sound; Making Settings For Digital Audio Input - Panasonic SC-BTX75 Operating Instructions Manual

Enjoying TV, etc. with this unit's speakers

TV
You can enjoy TV broadcasts with this unit's speakers.
SURROUND
SURROUND
STATUS
STATUS
Preparation
Confirm the audio connection to the OPTICAL IN or AUX terminal
on this unit ( 9 to 10).
Turn on the TV.
1 Press [EXT-IN] several times to select "D-IN 1"
(DIGITAL IN 1)* , "D-IN 2" (DIGITAL IN 2)*
1
"AUX"* .
1
This unit: Press [RADIO/EXT-IN].
≥D-IN 1 (DIGITAL IN 1)
*
1
When connecting using OPTICAL 1(TV) terminal.
≥D-IN 2 (DIGITAL IN 2)
* 2
When connecting using OPTICAL 2(STB) terminal.
:
≥AUX
*
1
When connecting using AUX terminal.
*1 For connections with the TV.
*2 For connections with other devices.
≥When the system is connected to an HDAVI Control 2 or
later-compatible TV via an HDMI cable, TV broadcast audio is
output through the system speakers if the TV input is switched to
TV tuner mode. See "Setting the TV audio for VIERA Link
"HDAVI Control"" on page 26 for setting method.
≥Reduce the volume on the TV to its minimum, and then adjust
the volume of this unit.

Adjusting the sound

You can adjust the mode depending on the source or situation.
1 Press [SOUND] several times to select the mode.
≥You can also press [SOUND] and then [3, 4] to select the
mode.
≥The selected effect will only be displayed on the main unit.
While the selected mode is displayed
2
Press [2, 1] and select the desired setting.
For more detailed information on this operation, please refer to
the "Changing the sound modes" section on page 15.
EXT-IN
EXT-IN
SOUND
SOUND
OK
or
2
:
:

Making settings for digital audio input

Select to suit the type of audio from the OPTICAL IN terminals on
the main unit.
≥Underlined items are the factory presets.
Available settings
Mode
DUAL: (Only works with Dolby Dual Mono)
– M1
–
M2
– M1+M2 (stereo audio)
≥If this is set to "M1" or to "M2", the PCM FIX
modes will automatically be set to "OFF".
DRC: – ON
Adjust for clarity even when the volume is low
(Dynamic
by compressing the range of the lowest sound
Range
level and the highest sound level. Convenient
Compression)
for late night viewing. (Only works with Dolby
Digital)
– OFF
The full dynamic range of the signal is
reproduced.
PCM FIX: – ON
Select when receiving only PCM signals.
– OFF
Select when receiving Dolby Digital and PCM
signals.
≥When receiving true 5.1-channel surround
sound, select "OFF".
≥If this is set to "ON", the DUAL mode will
automatically be set to "M1+M2".
–
TV AUDIO* : AUX
3
Select when receiving analogue sound from
the TV to the AUX terminal.
– D-IN 1
Select when receiving digital sound from the
TV to the OPTICAL 1(TV) terminal.
CABLE/SAT – SET
Select when setting the main unit to switch to
AUDIO* 4, 5 :
"D-IN 2" when the input channel of a HDMI
connected STB is selected on the TV (
Setting the TV audio for VIERA Link "HDAVI
Control").
– OFF
Select to cancel this setting.
1 Press [EXT-IN] several times to select "D-IN 1"
(DIGITAL IN 1) or "D-IN 2" (DIGITAL IN 2).
Main unit: Press [RADIO/EXT-IN].
2 Press [STATUS] several times to select the mode.
≥You can also press [STATUS] and then [3, 4] to select the
mode.
≥The digital audio input settings are to be set separately to
each source, "D-IN 1" and "D-IN 2".
≥The selected effect will only be displayed on the main unit.
While the selected mode is displayed
3
Press [2, 1] and select the desired setting.
*3 When "D-IN 1" is selected.
*4 When "D-IN 2" is selected.
*5 The device connected to the OPTICAL 2(STB) terminal must be
connected to the TV via an HDMI cable. If it is not connected via an
HDMI cable, "NOT CONDITIONAL" is displayed on the main unit.
≥Audio that is input through the OPTICAL DIGITAL IN
or AUX terminals are not output from the HDMI
terminal.
NOTE
Setting
26,
VQT2Q72
25