Advertisement
Performance Characteristics
* Denotes Warranted Specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 10°C from firmware calibration temperature.
Controls
Waveform intensity on front panel
Vectors on/off; infinite persistence
on/off
8 x 10 grid with continuous intensity
control
Built-in Help System
Key-specific help in 9 languages dis-
played by pressing and holding key
or softkey of interest
Real Time Clock
Time and date (user setable)
Measurement Features
Automatic Measurements
Measurements are continuously
updated
Cursors track current measurement
Voltage (analog channels only)
Peak-to-Peak, Maximum, Minimum,
Average, Amplitude, Top, Base,
Overshoot, Undershoot, RMS (front
panel: dc; GPIB: ac and dc)
Time
Frequency, Period, + Width,
- Width, Duty Cycle, X at Max (Time
at max volts), delay, phase on any
channels. Rise time and Fall time on
analog channels only
Threshold Definition
10%, 50%, 90% for time measure-
ments
Cursors
Manually or automatically placed
readout of Horizontal (X, ∆X, 1/∆X)
and Vertical (Y, ∆Y). Additionally dig-
ital or analog channels can be dis-
played as binary or hex values
Waveform Math
1-2, 1*2, FFT, dV/dt, ∫Vdt.
Source of FFT, dV/dt, ∫Vdt: scope
channels 1 or 2, 1-2, 1+2, 1*2
FFT
Points
Fixed at 2048 points
Source of FFT
Scope channels 1 or 2, 1+2, 1-2, 1*2
Window
Rectangular, Flattop, Hanning
Noise Floor
-70 to -100 dB depending on averag-
ing
Amplitude Display
In dBV
Frequency Resolution
0.097656/(time per div.)
Maximum Frequency
102.4/(time per div.)
10
Storage
Save/Recall (non-volatile)
3 setups and traces can be saved
and recalled internally
Floppy Disk
3.5" 1.44 MB double density
Image formats
TIF, BMP
Data formats
X and Y (time/voltage) values in CSV
format
Trace/setup formats
Recalled
I/O
RS-232 (serial) standard port
1 port: XON or DTR; 8 data bits;
1 stop bits; parity; 9600, 19200,
38400, 57600 baud rates
Parallel standard port
Printer support
Printer Compatibility
HP DeskJet, LaserJet with
HP PCL 3 or greater compatibility
black and white @ 150x150 dpi
gray scale @ 600x600 dpi
Epson
black and white @180x180 dpi
Seiko thermal DPU-414
black and white
Optional GPIB Module
Fully programmable with IEEE488.2
compliance
Typical GPIB throughput of 20 measurements or
20 2000-point records per second
General Characteristics
Physical:
Size
32.26 cm wide x 17.27 cm high x
31.75 cm deep (without handle)
Weight 6.35 kgs (14 lbs)
Calibrator Output
Frequency ~1.2 kHz; Amplitude ~5 V
Trigger Out
0 to 5 V with 50 Ω source impe-
dence; delay ~55 ns
Printer Power
7.2 to 9.2 V, 1 A
Kensington lock
connection on rear panel for security
Power Requirements:
Line Voltage Range
100 – 240 VAC ±10%, CAT II, auto-
matic selection
Line Frequency
47 to 440 Hz
Power Usage
100 W max
Environmental Characteristics:
Ambient Temperature
Operating –10°C to +55°C
Non-operating –51°C to +71°C
Humidity
Operating 95% RH at 40°C for 24 hr
Non-operating 90% RH at 65°C for
24 hr
Altitude
Operating to 4,570 m (15,000 ft)
Non-operating to 15,244 m (50,000 ft)
Vibration
HP/Agilent class B1 and MIL-PRF-
28800F Class 3 random
Shock
HP/Agilent class B1 and MIL-PRF-
28800F (operating 30 g,
11-ms duration, 3 shocks/axis along
major axis. Total of 18 shocks)
Regulatory Information:
Safety
IEC 61010-
1:1990+A1:1992+A2:1995/ EN
61010-1:1994+A2:1995
UL 3111
CSA-C22.2 No. 1010.1:1992
Supplementary Information: The product here-
with complies with the requirements of the Low
Voltage Directive 73/23/EEC and the EMC
Directive 89/336/EEC, and carries the CE-mark-
ing accordingly. The product was tested in a typ-
ical configuration with HP/Agilent test systems.
1
/
sine,
2
Advertisement
