Advertisement
QuickSpecs
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
NOTE:
NOTE:
NOTE:
ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on
Factory Integrated Model product offerings and requirements.
NOTE:
NOTE:
NOTE: HP does not allow factory integration of options into standard models listed above.
NOTE:
Configure-to-order servers must start with a Factory Integrated Model (CTO) Blade.
NOTE: FIO indicates that this option is a Factory Installable Option.
NOTE:
NOTE:
NOTE:
Step 1: Base Server Blade Configuration (Select a configurable Blade)
Step 1: Base Server Blade Configuration (Select a configurable Blade)
Step 1: Base Server Blade Configuration (Select a configurable Blade)
Step 1: Base Server Blade Configuration (Select a configurable Blade)
HP Models
HP Models
HP Models
HP Models
Step 2: Choose Required Options (one of the following from each list unless otherwise
Step 2: Choose Required Options (one of the following from each list unless otherwise
Step 2: Choose Required Options (one of the following from each list unless otherwise
Step 2: Choose Required Options (one of the following from each list unless otherwise
noted):
noted):
noted):
noted):
HP Processors
HP Processors
HP Processors
HP Processors
HP ProLiant BL620c G7 Configure-to-order Server
NOTE: This server supports the Intel Xeon 6500/7500 series processors.
NOTE:
NOTE:
NOTE:
HP ProLiant BL620c G7 Configure-to-order Server
NOTE:
NOTE:
NOTE:
NOTE: This server supports the Intel Xeon E7-2800/8867L series processors.
Configurable model ships with:
Configurable model ships with:
Configurable model ships with:
Configurable model ships with:
Four (4) integrated HP NC553i 10Gb FlexFabric adapter ports supporting
10Gb/1Gb autosensing Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-
based accelerated iSCSI, and iSCSI boot
One (1) 10/100 network adapter port dedicated to iLO 3 Management
One (1) Integrated SAS version 2.0 (6Gb) HP Smart Array P410i Controller with RAID
0 and 1
NOTE:
NOTE: The P410i is configured with no cache allowing the end user to select the
NOTE:
NOTE:
desired cache option (if cache is desired in the first place).
NOTE:
NOTE:
NOTE: RAID 0 and 1 are supported on the P410i without the need for a cache
NOTE:
option.
Two (2) cache slots for BBWC and/or FBWC battery options.
NOTE: The server supports up to a combined total of two (2) battery cache options
NOTE:
NOTE:
NOTE:
for the P410i and/or optional Smart Array RAID controllers.
Two (2) small form factor hot-plug SAS/SATA/SSD hard drive bays
Three (3) I/O expansion slots
One (1) integrated Lights-Out 3
Integrated USB, MicroSDHC, and TPM connectors
NOTE: The BL620c G7 supports one or two processors.
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: The minimum processor configuration is one processor that must be installed
in socket CPU1.
NOTE: All processors within the server must be identical.
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: All Configure-to-Order processor kits contain one (1) processor.
NOTE:
NOTE: If two processors are desired, select one xxxxxx-L21 kit and one xxxxxx-B21 kit.
NOTE:
NOTE:
NOTE:
Ten-Core Processors
Ten-Core Processors
Ten-Core Processors
Ten-Core Processors
HP BL620c G7 Intel® Xeon® E7-2870 (2.40GHz/10-core/30MB/130W) FIO
Processor Kit
HP BL620c G7 Intel® Xeon® E7-2860 (2.26GHz/10-core/24MB/130W) FIO
Processor Kit
HP BL620c G7 Intel® Xeon® E7-2850 (2.0GHz/10-core/24MB/130W) FIO
Processor Kit
DA - 13747
Worldwide — Version 16 — September 26, 2011
HP ProLiant BL620c Generation 7 (G7) Server Blade
HP ProLiant BL620c Generation 7 (G7) Server Blade
HP ProLiant BL620c Generation 7 (G7) Server Blade
HP ProLiant BL620c Generation 7 (G7) Server Blade
600332-B21
643786-B21
643749-L21
643751-L21
643753-L21
Page 20
Advertisement
