Pioneer XR-A550MD Service Manual page 85

QQ
3 7 63 1515 0
(e) TEMP Setting
Step No.
Step 1 Test mode STOP state
Step 2 Press the MENU button 7 times. EEPROM Setting Menu
Step 3 Press the
Step 4 Press the MENU button 4 times. TEMP Setting Menu
Step 5 Press the
Step No.
Step 1 EJECT status (or No Mechanism status)
Step 2 Press the ENTER button.
♦♦
: Set value, ??: Measured value
If the ¡ button is pressed while a setting item is being displayed, the set value will increase and the new set value will be set in LSI.
If the 1 button is pressed while a setting item is being displayed, the set value will increase and the new set value will be set in LSI.
If the ¡/1 buttons are pressed and held down, data will change continuously in 100ms cycles.
Measured Temperature Values
Correction Table
Ambient temperature
–0.9 °C to +2.7 °C
+2.7 °C to +6.3 °C
TE
L 13942296513
+6.3 °C to +10.0 °C
+10.0 °C to +14.5 °C
+14.5 °C to +18.2 °C
+18.2 °C to +22.3 °C
+22.3 °C to +26.3 °C
+26.3 °C to +30.3 °C
+30.3 °C to +34.6 °C
+34.6 °C to +39.0 °C
+39.0 °C to +42.8 °C
(f) CONTROL Setting
Step No.
Step 1 Test mode STOP state
Step 2 Press the MENU button 7 times. EEPROM Setting Menu
Step 3 Press the
Step 4 Press the MENU button 5 times. CONTROL Setting Menu
Step 5 Press the
Step 6 Press the MENU button.
Step 7 Press the MENU button.
Step 8 Press the MENU button.
Step 9 Press the MENU button.
www
Step 10 Press the MENU button.
Step 11 Press the MENU button.
.
Step 12 Press the MENU button.
Step 13 Press the MENU button.
http://www.xiaoyu163.com
Setting Method
`
button. Focus Setting Menu
`
button. TEMP standard value setting
Setting Method
EEPROM recording value = microcomputer measured value + correction value
* EEPROM recording value
Correction value
Predicted value when measured with microcomputer when temperature is +25 °C.
–06 H
* Microcomputer measured value
–05 H
Predicted value when measured with microcomputer at a certain temperature.
–04 H
* Correction value
–03 H
Correction value for converting to +25 °C measured value (see Table at left).
–02 H
Temperature Code Confirmation
–01 H
After AUTO Adjustment has been completed, the temperature code will be read. If it is within
±0 H
the ranges below, it is OK.
+01 H
+02 H Ambient temperature
+03 H –18.2 °C to +30.3 °C
+04 H
+6.3 °C to +18.2 °C
Setting Method
`
button. Focus Setting Menu
`
button. CONTROL 1 Setting
CONTROL 2 Setting
Spin kick level setting during Move
Readjustment interval (minutes) setting
Equalizer coefficient A, D (high reflectance) setting
Equalizer coefficient A, D (low reflectance) setting
x ao
y
Equalizer coefficient A, D (low reflectance groove) setting
i
Equalizer coefficient B, C (high reflectance) setting
Equalizer coefficient B, C (low reflectance pit) setting
http://www.xiaoyu163.com
8
Remarks
Remarks
TEMP standard value setting
Q Q
3 6 7 1 3
Temperature Code
06
07
Remarks
u163
.
XR-A550MD
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
9 9
Display
[ tsm????e?? ]
[ EEPROM_ SET]
[ _ _ Focus_ _ _ ]
[ _ _ _ Temp_ _ _ ]
♦♦
[ TEMP_ ??_
]
Display
[ _ _ EJECT_ _ _ ]
♦♦
[ TEMP_??_ ]
2 8 9 9
Display
[ tsm????e?? ]
[ EEPROM_ SET]
[ _ _ Focus_ _ _ ]
[ _ Control_ _ ]
♦♦
[ CONTRL1_ ]
♦♦
[ CONTRL2_ ]
♦♦
[ SPKLEVm_ ]
♦♦
[ ADJTTM_ ]
♦♦
[ HDEQAD_ ]
♦♦
[ LDEQAD_ ]
♦♦
[ GDEQAD_ ]
♦♦
[ HDEQBC_ ]
♦♦
[ LDEQBC_ ]
85