Setting Up - Panasonic NV-VHD1EC Operating Instructions Manual

Aerial
(not supplied)
RF coaxial lead
(supplied)
21-pin scart lead
(not supplied)
On Screen Display
Panasonic
Country
Belgien Deutschland
Belgique Österreich
Belgiê Portugal
Panasonic
Clock setting
Clock setting : MAN.
Time : 20:30:24
Date : 21.03.01
Panasonic
Panasonic VCR
Download
Download
Download in
progress,
please wait.
Position 49
VCR display
Panasonic VCR
Main menu
Timer recording
Tuning
Clock setting
Other settings
Panasonic VCR
Tuning
Manual
Auto-Setup Restart
Download
Shipping condition
VCR / DVD
RF Coaxial lead
(supplied)
VCR display
On Screen Display
VCR
Ch:36
RQTD0035-A
Set up the connections shown here and connect the mains lead (supplied) to your AC IN.
The RF (radio frequency) coaxial lead must be connected for TV reception,
TV
even if the video recorder is already connected with a 21-pin scart lead.
(not supplied)
For more information about the remote control buttons and cursors see pages 4-5.
Automatic Setting without Q Link
Set the remote control to VCR
Switch on the unit
Use the cursors
After pressing |ENTER|, all the TV stations which can be received will be tuned automatically in about 5 minutes.
If the menu [Clock setting] appears, use the cursors
on the remote control to set the Time and Date manually.
VCR
To end this procedure, press |ENTER|.
To cancel this settings press |EXIT|.
Note: If the selection for the Country menu does not appear after switching on the unit, you can restart
the automatic setting; see page 10. An incorrect setting of time or date (observe summer- and wintertime)
VCR
will influence the timer recording.
Automatic Setting with Q Link
If your TV is equipped with Q Link or with a similar function from other manufacturers (see note),
VCR
the TV programme positions can be downloaded with a fully-wired 21-pin scart lead (not supplied).
The programme positions must be tuned on the TV first.
Connect the scart lead.
Set the AV channel of the TV.
Set the remote control to VCR
Switch on the unit
Downloading of the TV data starts.
When the channel indication stops flashing on the VCR display, the downloading is complete.
Note about
Panasonic. List of registered trademarks: Q Link (Panasonic), DATA LOGIC (Metz), Easy Link (Philips),
Megalogic (Grundig), SMARTLINK (Sony)
Manual download start
Set the AV channel of the TV.
Set the remote control to VCR
Press |MENU|
Select [Tuning]
Access by pressing |ENTER|
Select [Download]
Press |ENTER|
Confirm by pressing |ENTER|
When the channel indication stops flashing on the VCR display, the downloading is complete.
Connect the TV only with a RF coaxial lead
You must ensure that the video output channel is adjusted to the input channel of the TV.
Please also read the operating instructions for your TV.
TV
Set the remote control to VCR
Switch on the unit
Press |MENU| for about 7 seconds until the number of the channel appears
on the VCR display. The pre-setting is channel 36 (NV-VHD1 EC) 38 (NV-VHD1 EE).
Tune the TV until the test screen appears. A distorted picture on the channel can be reduced
by adjusting the unit and the TV to another channel.
Use the |CH| button or the numeric buttons to select the channel number (e.g. channel 39).
Tune the TV until the test screen appears.
To store this adjustment, press |ENTER| .
After that, please continue with the Automatic Setting with the [Country] setting menu.
and the [Country] setting menu will appear.
on the remote control to select your country.
.
.
: The following systems from other manufacturers have a similar function to Q Link from
.
.

Setting up

or the numeric buttons
AC IN~
AC mains lead
(supplied)
3