KitchenAid KGCU467VSS Installation Instructions Manual page 15

4. Apply masking tape to the end of a 7 mm nut driver to help
hold the gas orifice spud in the nut driver while changing it.
Insert nut driver into gas opening and press down onto the
gas orifice spud and remove by turning the gas orifice spud
counterclockwise and lifting out. Set gas orifice spud aside.
5. Replace with correct LP gas orifice spud. See the "LP Gas
Orifice Spud/Hood Chart."
Use the following chart to find the exact orifice spud
placement.
Fully insert choke into bottom of medium burner base.
Choke should snap into place. Refer to illustration to
verify that choke is fully seated.
NOTE: Chokes are placed on medium burners only.
Incorrectly seated choke
Correctly seated choke
LP Gas Orifice Spud/Hood Chart
Burner
Color
Rating
3,000 BTUs Blue
11,000 BTUs Yellow
14,000 BTUs Red/
Green
Green
14,500 BTUs Black
Burner orifice spud
A
A. Size stamp or color
Size Burner Style
0.55 mm Small burners
0.97 mm Medium burners
C
Choke
1.05 mm Large burner - main
0.35 mm Large burner - simmer
1.18 mm Grill burner
(on some models)
Grill orifice hood
A
A. Size stamp
6. Place Natural gas orifice spuds in plastic parts bag for future
use and keep with package containing literature.
NOTE: There may be extra orifices in your kit.
7. Replace the burner base.
8. Replace burner cap.
9. Repeat steps 2 through 8 for the remaining burners.
To Convert Grill Burner (on some models)
1. Remove grill grate, wave plate, flame spreader and burner
assembly. See the "Install Grill Grease Trays" section for
removal instructions. Set parts aside.
2. Use a / " deep-well socket to remove the Natural gas orifice
1
2
hood. Replace with correct grill LP gas orifice hood. See the
"LP Gas Orifice Spud/Hood Chart."
A
A. Grill orifice hood location
3. Turn LP gas orifice hood down tightly onto orifice base.
4. Place Natural gas orifice hoods in plastic parts bag for future
use and keep with package containing literature.
5. Before replacing the burner assembly, loosen the screw at
the front of the burner and rotate the shutter so that the
opening is / " (8.0 mm) wide.
5
16
A. Shutter opening
B. Screw
6. Reinstall the burner assembly, flame spreader, wave plate,
and grill grate. See the "Install Grill Grease Trays" section for
A
installation instructions.
B
7. Open shut-off valve in the gas supply line. The valve is open
when the handle is parallel to the gas pipe.
REMEMBER: Once you have completed converting the
grill, test the cooktop for leaks by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show,
indicating a leak. Correct any leaks found.
8. Plug in cooktop or reconnect power.
Complete Installation
1. Refer to the "Make Gas Connection" section for properly
connecting the cooktop to the gas supply.
2. Refer to the "Electronic Ignition System" section for proper
burner ignition, operation, and burner flame adjustments.
IMPORTANT: You may have to adjust the Lo setting for each
cooktop burner.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
/ " (0.64 cm) to / " (1.3 cm) long. The outer cone is not
1 1
4 2
as distinct as the inner cone. LP gas flames have a slightly
yellow tip.
3. Refer to "Complete Installation" in the "Installation
Instructions" section of this manual to complete this
procedure.
A
B
15