Connecting An External Amplifier - JVC KW-AVX716 Instructions Manual

ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Before connecting Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
:
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Rear ground terminal
* 2 Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
White with black stripe
A

Connecting an external amplifier

You can connect an amplifier to upgrade your car stereo system.
• You can supply the power to the amplifier by connecting the remote leads (blue with white stripe) of
this unit to the amplifier. (To connect other equipment using the remote leads, Y-connectors need to
be separately purchased.)
• Disconnect the speakers from the unit, and connect them to the amplifier. Leave the speaker leads of
the unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier
to get clear sound and to prevent internal heat built-up inside the unit. See page 49 of the
INSTRUCTIONS.
Remote lead (Blue with white stripe)
Front speakers
* 3 Firmly attach the ground lead to the metallic body or to the chassis of the car—to the place uncoated
with paint (if coated with paint, remove the paint before attaching the lead). Failure to do so may
cause damage to the unit.
B
Connections for external component playback
AV amplifier or decoder
Digital optical cable
(not supplied)
Audio/video cord (not supplied)
Downloaded from Caradio-Manual.com Manuals
Fan
Black
Yellow *
Red
Blue
15 A fuse
Blue with white stripe
Orange with white stripe
Brown
Light green
White Gray with black stripe
Left speaker (front)
Y-connector (not
supplied for this unit)
Remote lead
JVC Amplifier
* 3
Crimp connector
(not supplied)*
Extension lead (not supplied)
To car battery
Reverse lamp lead*
Video cord
(not supplied)
Camcorder, Navigation
System, etc.
External
monitor
Rear view camera KV-CM1*
6
See each diagram below.
* 1 Not included for this unit
To metallic body or
chassis of the car
2
To a live terminal in the fuse block connecting to
the car battery (bypassing the ignition switch)
To an accessory terminal in the fuse block
Gray Green with black stripe
Right speaker (front)
C
Connections to the CD changer jack
When connecting the external components, refer also to the manuals supplied for the components and adapter.
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
You can connect the following JVC components to the CD changer jack.
JVC component
CD changer (CD-CH)
You can also connect the following components through the various JVC adapters.
• Connection cords may need to be purchased separately.
To the remote
lead of other
Component
equipment
Bluetooth device
iPod
Portable audio player with line output jacks
Rear
Portable audio player with 3.5 mm stereo mini jack
speakers
When connecting more than one component (maximum: two), it is recommended that you connect the
components in series as explained below.
When connecting two components in series
CD changer jack
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
5
To reverse
lamp
4
Reverse lamp
2
Ignition switch
* 1
* 1
To automatic antenna
if any (250 mA max.)
To the remote lead of other equipment (200 mA max.)
To car light control switch
To cellular phone system
To parking brake (see diagram
Crimp connector
Green Purple with black stripe
Left speaker (rear)
Model name
CH-X1500, etc.
Adapter
Bluetooth adapter
Interface adapter for iPod
Line input adapter
AUX input adapter
A
KS-BTA200
B* 7
CD-CH / KS-PD100 / KS-U57 / KS-U58
To disconnect the connector
Hold the connector top tightly
( 1 ), then pull it out (
* Required only when connecting a rear view camera
4
to VIDEO IN terminal.
* 5 Refer to å in diagram
* 6 Set "AV Input" setting to "Camera" when using (see
page 47 of the INSTRUCTIONS).
Fuse block
Å on page 1.)
Purple
Right speaker (rear)
Model name
KS-BTA200
KS-PD100
KS-U57
KS-U58
7
* To use these components,
set the external input setting
correctly (see page 47 of the
INSTRUCTIONS).
2 ).
Å on page 1.