Advertisement
Disc, USB
Inserting or removing media
Basic playback
Press [CD] or [USB] to select the source.
Disc
Play
Press [4/9].
Press [CD x OPEN/CLOSE] on the main unit to
open the sliding door.
Stop
Press [8].
Put in a disc with the label facing towards you.
USB
:
The track is memorised.
"RESUME" is shown.
Press two times to stop fully.
Click!
Pause
Press [4/9].
Press again to continue
playback.
Skip track
Press [2/3] or [5/6].
Search
Press and hold [2/3] or
Note:
through track
[5/6].
Keep fingers away from the sliding door when it is
closing.
Skip album
Press [R, T].
View
Press [DISPLAY].
USB
information
Note:
USB device
•
Maximum characters that can be shown:
(not supplied)
approximately 32
This system supports ver. 1.0, 1.1 and 2.3 ID3
•
tags.
•
Text data that the system does not support can
show differently.
Note:
Do not use a USB extension cable. The system
cannot recognise USB device connected through a
cable.
Radio
To preset the station
30 FM stations can be preset.
4
Press [OK].
Preparation
Connect the FM antenna (Z "Getting started").
5
Press [R, T] to select a preset number.
Press [RADIO].
6
Press [OK].
Do steps 3 through 6 again to preset more
Automatic presetting
stations.
Note:
1
Press [PLAY MENU] to select "A.PRESET".
A station previously stored is overwritten when
another station is stored in the same preset number.
2
Press [R, T] to select "LOWEST" or
"CURRENT" frequency.
LOWEST : To begin auto preset from the lowest
Selecting a preset station
frequency.
CURRENT : To begin auto preset from the
1
Press [PLAY MENU] to select "TUNEMODE".
current frequency .
To change the frequency, refer to "Manual
2
Press [R, T] to select "PRESET" and then
tuning and presetting".
press [OK].
3
Press [OK] to start presetting.
3
Press [2/3] or [5/6] to select the
The tuner presets all the stations it can receive
preset station.
into the channels in ascending order.
To cancel, press [8].
RDS broadcasting
Manual tuning and presetting
This system can show the text data transmitted
by the radio data system (RDS) available in some
areas.
1
Press [PLAY MENU] to select "TUNEMODE".
2
Press [R, T] to select "MANUAL" and then
Press [DISPLAY].
press [OK].
PS
Station name
3
Press [2/3] or [5/6] to tune in to the
PTY
Program type
station.
FREQ
Frequency
To tune automatically, press and hold the button
until the frequency starts changing quickly.
"STEREO" is shown when the system is tuned in
Note:
RDS may not be available if reception is poor.
to a stereo broadcast.
Play menu
Compatible media
1
Press [PLAY MENU] to select "PLAYMODE" or
Disc
"REPEAT".
•
This system can play CD-R/RW with CD-DA or
2
Press [R, T] and then press [OK] to select the
MP3 format content.
desired mode.
Some CD-R/RW cannot be played because of the
•
condition of the recording.
PLAYMODE
MP3 files are defined as tracks and folders are
•
defined as albums.
OFF
Play all tracks.
This system can access up to:
PLAYMODE
•
– CD-DA : 99 tracks
1-TRACK
Play one selected track.
– MP3
: 999 tracks, 255 albums (including root
Press [2/3] or [5/6]
1
folder) and 20 sessions
to select the track.
Disc must conform to ISO9660 level 1 or 2 (except
•
for extended formats).
1-ALBUM
Play one selected album.
•
Recordings will not necessarily be played in the
Press [R, T] to select the
1
order you recorded them.
album.
RANDOM
Play all tracks randomly.
RND
USB
1-ALBUM
Play all tracks in one selected
Compatible USB devices which are defined as
•
RANDOM
album randomly.
mass storage class:
1
RND
Press [R, T] to select the
– USB devices that support bulk-only transfer
album.
– USB devices that support USB 2.0 full speed
REPEAT
Files are defined as tracks and folders are defined
•
as albums.
ON REPEAT
Repeat playback.
Track must have the extension ".mp3" or ".MP3".
•
This system can access up to:
•
OFF REPEAT
Cancel repeat playback.
– 255 albums (including root folder)
– 2500 tracks
– 999 tracks in one album
Note:
•
CBI (Control/Bulk/Interrupt) is not supported.
During random playback, you cannot skip to tracks
•
•
NTFS file system is not supported (only FAT
which have been played.
12/16/32 file system is supported).
The setting returns to default when you open the
•
•
Some files can fail to work because of the sector
sliding door.
size.
Sound effects
Improving the sound quality
1
Press [SOUND] to select a sound effect.
2
Press [R, T] to select the desired setting.
1
Press [PLAY MENU] to select "FM MODE".
PRESET EQ
"HEAVY" : Adds punch to rock.
2
Press [R, T] to select "MONO" and then
"SOFT" : For background music.
press [OK].
"CLEAR" : Clarifies higher
To cancel, select "STEREO".
frequencies.
"MONO" is also cancelled when you change the
frequency.
"VOCAL" : Adds gloss to vocal.
"FLAT"
: Cancels the sound
To memorise the setting
effect.
Continue with steps 4 through 6 of "Manual tuning
BASS
"BASS -4" to "BASS +4".
and presetting".
TREBLE
"TREBLE-4" to "TREBLE+4".
D.BASS
"ON D.BASS" or "OFF D.BASS".
Checking the signal status
SURROUND
"ON SURROUND" or
"OFF SURROUND".
Press [PLAY MENU] to select "FM STATUS" and
then press [OK].
FM
The FM signal is in monaural.
The system is not tuned in to a
station.
FM ST
The FM signal is in stereo.
Maintenance
FM MONO
"MONO" is selected as the
"FM MODE".
To clean this system, wipe with a soft, dry cloth.
•
Never use alcohol, paint thinner or benzine to clean
this system.
Before using chemically treated cloth, read the
•
instructions that came with the cloth carefully.
Clock and timers
Setting the clock
Play timer
This is a 24-hour clock.
You can set the timer to come on at a certain time to
wake you up.
1
Press [SETUP] to select "CLOCK".
Preparation
2
Press [R, T] to set the time.
Set the clock.
3
Press [OK].
1
Press [SETUP] to select "TIMER ADJ".
To show the clock for a few seconds
2
Press [R, T] to set the start time.
Press [SETUP] to select "CLOCK" and then press
[OK].
3
Press [OK].
4
Do steps 2 and 3 again to set the end time.
Note:
Reset the clock regularly to maintain accuracy.
To start the timer
1
Prepare the audio source you want to listen to
and set the volume.
Sleep timer
2
Press [SETUP] to select "TIMER SET".
The sleep timer switches off the system after the set
3
Press [R, T] to select "SET" and then press
time.
[OK].
Press [SLEEP] to select the setting (in minutes).
"#" is shown.
To cancel, select "OFF".
The system must be switched off for the timer to
operate.
SLEEP 30 → SLEEP 60 → SLEEP 90
OFF ← SLEEP120
Check the
1. Press [SETUP] to select
settings
"TIMER ADJ".
Note:
2. Press [OK].
•
The remaining time is always shown on the display.
Cancel
1. Press [SETUP] to select
The display changes temporarily when you perform
"TIMER SET".
other operations.
2. Press [R, T] to select "OFF"
•
The sleep timer can be used together with the play
and then press [OK].
timer.
The sleep timer always comes first. Be sure not to
•
set an overlap of timers.
Troubleshooting
Before requesting service, make the following
USB
checks. If you are in doubt about some of the check
points, or if the solutions indicated do not solve the
The USB device or the contents in it cannot be
problem, consult your dealer for instructions.
read.
•
The format of the USB device or the contents in it
Common problems
is/are not compatible with the system.
•
USB devices with storage capacity of more than
No operations can be done with the remote
32 GB cannot work in some conditions.
control.
•
Examine that the battery is installed correctly.
Slow operation of the USB device.
The remote control and this unit are using different
•
•
Large content size or large memory USB device
codes (Z right, "REMOTE ").
takes longer time to read.
Sound is distorted or no sound.
Adjust the volume of the system.
The elapsed time shown is different from the
•
actual play time.
•
Switch off the system, determine and correct the
cause, then switch the system on again. It can
•
Transfer the data to another USB device or backup
be caused by straining of the speakers through
the data and reformat the USB device.
excessive volume or power, and when using the
system in a hot environment.
Radio
A "humming" sound can be heard during
A beat sound is heard.
playback.
Switch off the TV or move it away from the system.
•
•
An AC mains lead or fluorescent light is near the
•
Move mobile telephones away from the unit if the
cable. Keep other appliances and cords away from
interference is apparent.
the cable of this system.
Main unit displays
Disc
"--:--"
Display not shown correctly.
•
You connected the AC mains lead for the first time
Playback does not start.
or there was a power failure recently. Set the clock.
You did not put the disc in correctly. Put it in
•
correctly.
"ADJUST CLOCK"
•
Disc is dirty. Clean the disc.
•
Clock is not set. Adjust the clock accordingly.
Replace the disc if it is scratched, warped, or
•
non-standard.
"ADJUST TIMER"
•
There is condensation. Let the system dry for 1 to
Play timer is not set. Adjust the play timer
•
2 hours.
accordingly.
Specifications
Note:
Amplifier section
•
The timer starts at a low volume and increases
gradually to the preset level.
RMS output power stereo mode
The timer comes on at the set time every day if the
•
Front Ch (both ch driven)
timer is on.
5 W per channel (6 ), 1 kHz, 10% THD
•
If you switch off the system and switch on again
Total RMS stereo mode power
while a timer is in operation, the timer will not stop
at the end time.
Tuner section
Preset station
FM 30 stations
Frequency modulation (FM)
Auto off function
CD
USB
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
This function switches off the system (except in
radio source) if you do not use the system for
Antenna terminals
75
(unbalanced)
approximately 30 minutes.
Terminals section
1
Press [SETUP] to select "AUTO OFF".
USB port
2
Press [R, T] to select "ON" or "OFF" and
USB standard
USB 2.0 full speed
then press [OK].
Media file format support
MP3 (*.mp3)
USB device file system
FAT12, FAT16, FAT32
USB port power
500 mA (max)
Headphones jack
Terminal
Stereo, 3.5 mm jack
Disc section
Disc played (8 cm or 12 cm)
CD, CD-R/RW (CD-DA, MP3 )
Pick up
Wavelength
790 nm (CD)
Laser power
Audio output (Disc)
Number of channels
2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
MPEG-1 Layer 3, MPEG-2 Layer 3
"ERROR"
"REMOTE " (" " stands for a number.)
•
An incorrect operation was done. Read the
The remote control and this unit are using different
•
instructions and try again.
codes. Change the code of the remote control.
– When "REMOTE 1" is shown, press and hold
"F61"
[OK] and [T] for a minimum of 4 seconds.
There is a power supply problem.
•
– When "REMOTE 2" is shown, press and hold
[OK] and [R] for a minimum of 4 seconds.
"USB OVER CURRENT ERROR"
•
The USB device is drawing too much power.
"–VBR–"
Remove the USB device. Switch the system off
•
The system cannot show the remaining play time
and on again.
for variable bit rate (VBR) tracks.
"NODEVICE"
The USB device is not connected. Examine the
•
Memory reset (initialisation)
connection.
Reset the memory when the following situations
"NO DISC"
•
You have not put in a disc.
occur:
There is no response when buttons are pressed.
•
"NO PLAY"
You want to clear and reset the memory contents.
•
You have put in a disc that the system cannot play.
•
1
Disconnect the AC mains lead.
You have inserted a USB device that cannot be
•
Wait 3 minutes before you continue with step 2.
played. Examine the content. You can only play
supported format.
2
While you press and hold [1] on the main
If there are more than 255 albums or folders (audio
•
unit, connect the AC mains lead again.
and non-audio), some of the MP3 files in these
"– – – – – – – –" is shown.
albums cannot be read and played. Transfer these
3
Release [1].
music albums to another USB device. Alternatively,
All the settings are set back to the factory preset.
reformat the USB device and save these music
It is necessary to set the memory items again.
albums prior to saving the other non-audio folders.
"NOT MP3/ERROR"
An unsupported MP3 format. The system will skip
•
that track and play the next one.
Speaker section
Type
1 way, 1 speaker system (bass reflex)
Speaker unit(s)
Full range
8 cm cone type x 1/ch
10 W
Impedance
6
General
Power supply
AC 220 to 240 V, 50 Hz
Power consumption
12 W
Dimensions (W x H x D)
400 mm x 213 mm x 110 mm
[D = 72 mm (min)]
Mass
1.9 k
g
Operating temperature range
0°C to +40°C
Operating humidity range
35% to 80% RH (no condensation)
Power consumption in standby mode
0.2 W (approximate)
Note:
Specifications are subject to change without notice.
•
Mass and dimensions are approximate.
•
Total harmonic distortion is measured by the digital
spectrum analyzer.
CLASS
I
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote
control code for this system.
To set the code to "REMOTE 2"
1
Press and hold [CD] on the main unit and [R]
on the remote control until "REMOTE 2" is
shown.
2
Press and hold [OK] and [R] for a minimum of
4 seconds.
To set the code to "REMOTE 1"
1
Press and hold [CD] on the main unit and [T]
on the remote control until "REMOTE 1" is
shown.
2
Press and hold [OK] and [T] for a minimum of
4 seconds.
Advertisement
