Setting Menu Configuration - Panasonic AK-HC3500AES Operating Instructions Manual

Setting menu configuration

Hierarchical menus
USER MENU
Operation
VF Setting1
Viewfinder settings1
VF Setting2
Viewfinder settings2
Cursor
Cursor settings
VF Display1
Viewfinder display settings1
VF Display2
Viewfinder display settings2
Setting1
Camera settings1
Setting2
Camera settings2
28
Side Modu SW (for setting the peripheral brightness modulation to ON or OFF)
Side Modu LVL (for setting the peripheral brightness modulation level)
Zone Mark (for setting the zone marker)
Safety Mark1 (for setting the safety marker1)
Safety Area1 (for setting the safety area1)
Safety Mark2 (for setting the safety marker2)
Safety Area2 (for setting the safety area2)
Center Mark (for setting the center marker)
Center Mark SEL (for setting the shape of the center marker)
Line Width (for setting the thickness of the markers)
Marker Level (for setting the brightness of the markers)
VF DTL (for adjusting VF DTL)
RET Signal
HD Peak FREQ (for adjusting the peak frequency of HD RET signal)
HD Offset Gain (for adjusting the DTL offset gain of HD RET signal)
HD Crisp (for adjusting the DTL crisp level of HD RET signal)
D1 Peak FREQ (for adjusting the peak frequency of D1 RET signal)
D1 Offset Gain (for adjusting the DTL offset gain of D1 RET signal)
D1 Crisp (for adjusting the DTL crisp level of D1 RET signal)
VBS Peak FREQ (for adjusting the peak frequency of VBS RET signal)
VBS Offset Gain (for adjusting the DTL offset gain of VBS RET signal)
VBS Crisp (for adjusting the DTL crisp level of VBS RET signal)
Cursor (for setting the cursor marker to ON or OFF)
Cursor Memory (for selecting the cursor marker memory from ADJ, 1, 2 or 1+2)
H Position (for adjusting the H position of the cursor)
V Position (for adjusting the V position of the cursor)
Width (for adjusting the width of the cursor)
Height (for adjusting the height of the cursor)
BOX/CROSS (for setting the shape of the cursor)
Store Memory (for setting the cursor memory)
EXECUTE (for executing Store)
F Number (for setting the f-number display to ON or OFF)
Zoom (for setting the zoom value display to ON or OFF)
Focus (for setting the focus value display to ON or OFF)
Extender (for setting the lens extender display to ON or OFF)
MONI OUT (for setting the monitor output selection display to ON or OFF)
Filter (for setting the ND/CC filter display to ON or OFF)
M Gain (for setting the gain display to ON or OFF)
Shutter (for setting the electronic shutter display to ON or OFF)
5600K (for setting the 5600K effect to ON or OFF)
Audio Level (for setting the audio level display to ON or OFF)
OPT Level (for setting the optical level display to ON or OFF)
RET Select (for setting the RET selection display to ON or OFF)
Status (for setting the display appearing when functions are selected to ON or OFF)
Status(AUTO) (for setting the display appearing when AWB/ABB/ASU are started or finished to ON or OFF)
Field Rate (for setting the field rate display to ON or OFF)
Voltage (for setting the supply voltage display to ON or OFF)
WFM (for setting the WFM display to ON or OFF)
White CH (for setting the white balance memory display to ON or OFF)
FAN Power (for setting the camera fan to ON or OFF)
FAN Mode (for setting the camera fan mode)
CALL+R_TALLY (for setting to light R TALLY when CALL is detected)
CALL+T_TALLY (for setting to light T TALLY when CALL is detected)
PinP Mode (not operate)
HD-SDI2 OUT (for selecting the mode of HD-SDI2 connector)
HD-SDI2 Power (for setting the power of HD-SDI2 to ON or OFF)
AUX I/O (for selecting the mode of AUX connector)
TRUNK1 (for setting the serial interface standard of trunk line)
TRUNK2 (for setting the serial interface standard of trunk line)
5600K (for setting the electronic color temperature filter)
HND GRIP RET (for selecting the grip RET SW function)
HND GRIP PTT (for selecting the grip PTT SW function)
HND Lens VTR (for selecting the handy lens VTR SW function)
HND Lens RET (for selecting the handy lens RET SW function)
STD Lens RET1 (for selecting the standard lens RET1 SW function)
STD Lens RET2 (for selecting the standard lens RET2 SW function)
EXT RET 1 (for selecting the external return control SW1 function)
EXT RET 2 (for selecting the external return control SW2 function)
EXT RET 3 (for selecting the external return control SW3 function)