Table of Contents
Advertisement
Settings & Preferences – Overview
Press and hold the BRT and SEN buttons to access Preferences. To exit Preferences, simply wait a few
seconds without pressing a button. A
Completed
message will display confirming your selection(s).
Press BRT to go from
one category to the next
User Mode
Advanced*
Novice
Pilot Mode
Scanning*
Full Word
Arrow Mode
Single*
Multiple
Band
Display Color
Blue* / Green / Red / Amber
Speed Display
On*
Off
Cruise Alert
20 mph*
Off / 20-160 mph
Over Speed
70 mph*
Off / 20-160 mph
Meter Mode
Standard
Standard FR1*
Standard FR2
Spec FR1
Spec FR2
Expert FR
Simple
Standard*
Tones
Standard+
Mild
AutoMute
Low / Med* / High / Off
Press + or – to change
your setting within a category
Access and customize all Settings and Preferences
Access and customize units and display color, (all other
Settings are set to factory defaults)
NOTE: Switch to Advance mode to view all Preferences
Scanning Bar with Full Word
Full Word: Auto, Auto NoX, or Highway
Displays blue threat-direction arrow for primary alert band
Displays threat-direction arrows for multiple alerts based on
Meter Mode settings.
Front radar alert band = blue, Rear radar alert band = red
Displays color-coded threat-direction arrows for multiple alert
bands, based on Meter Mode settings.
X = green, K = blue, Ka/Laser = red
Set color to match your vehicle's dash display
Displays current speed
Displays battery voltage
Offers double-beep alert tones if traveling below specified speed
Reminds you when you exceed a specified speed
Primary alert band, with bar graph of signal strength
Primary alert band, with front and/or rear bar graph(s) of
signal strength
Primary and secondary alert bands, with front and/or rear
bar graph(s) of signal strength
Primary alert band, with numeric frequency and front
and/or rear bar graph(s) of signal strength
Primary and secondary alert bands, with numeric
frequencies and front and/or rear bar graph(s) of
signal strength
Multiple alert bands, with front and/or rear bar graph(s) of
signal strength for each
Caution
(if traveling below Cruise Alert limit)
Slow Down
(if traveling above Cruise Alert limit)
Standard ESCORT alert tones
Standard ESCORT alert tones for primary alert and
double-beep tones for additional alerts
Mild doorbell chime alert tones
Automatically reduces audio to preferred volume during alert
On* / Off
AutoLearn
Units
English* / Metric
Language
English* / Espanol
Voice
On* / Off
GPS Filter
On* / Off
AutoPower
Off
Power turns on or off depending on your vehicle's ignition type
(constant power or switched)
1 Hour
Powers off automatically after 1 hour
2 Hours
Powers off automatically after 2 hours
4 Hours*
Powers off automatically after 4 hours
8 Hour
Powers off automatically after 8 hours
NOTE: AutoPower only works with constant power-ignition. If AutoPower is on,
the display screen goes blank after 30 minutes to save screen life.
Display screen will turn on automatically after you reach 10 mph
Band Enables
Default*
Default Settings for North America
Modified
Customize the bands you want to monitor
Press SEN to modify
Press + or – to change
band preferences and go from
your setting within a category
one category to the next
X Band
On* / Off
On* / Off
K Band
Ka Band
On* / Off
Ka-POP
On / Off*
Laser
On* / Off
All laser guns used in North America
TSR
On* / Off
Automatically rejects traffic-flow-sensor false alarms
Marker Enables
Default*
All markers on
Modified
Customize the types of locations you want to mark for future reference
Press SEN to modify marker
Press + or – to change
preferences and go from
your setting within a category
one category to the next
Other
On* /Off
Other location
On* / Off
Redlight
Red light camera
Red & Speed
On* / Off
Red light & speed camera
Speed Camera
On* / Off
Speed camera
Speed Trap
On* / Off
Speed trap
Air Patrol
On / Off*
Known aircraft patroled areas
NOTE: User cannot mark an Air Patrol location
Marked
Clear Locations
Clear all user-marked locations. Press SEN button to confirm
Lockouts
Clear all lockouts. Press SEN button to confirm
Defender
Clear all DEFENDER Database data. Press SEN button to confirm
Format
Clear DEFENDER Database, all markers, and all lockouts.
*Default Setting
Automatically stores and locks out false alarms
Units for distance and speed
Language for voice and text
Voice announcements
Enables GPS-powered features
Restore Factory Settings
To restore ESCORT Max 360 to its original factory
settings, press and hold BRT and MRK while turning
the power on. A "Restored" message will display,
acknowledging the reset.
Hide quick links:
Advertisement
Table of Contents
