Table Of Contents; Caution For Ac Mains Lead (Uk And Republic Of Ireland Only); Important Safety Instructions For The User - Panasonic MC-CL481K Operating Instructions Manual

Hide thumbs Also See for MC-CL481K:
Table of Contents

Advertisement

TABLE OF CONTENTS

............................................................... 2

CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only)

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded 'three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to
BS1362.
Check for the ASTA mark
or the BSI mark
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED
AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.
Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the
Earth Symbol
How to replace the Fuse:
• There are two types of supplied AC Mains Lead A and B as shown below.
1. Open the fuse compartment with a screwdriver.
2. Replace the fuse and fuse cover if detachable.

IMPORTANT SAFETY INSTRUCTIONS FOR THE USER

Before using the vacuum cleaner, please observe these basic precautions.
WARNING: To reduce the risk of fire, electric shock, or injury.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Do not use the appliance if the mains lead or plug is damaged or faulty.
• This appliance is provided with a mains lead and if this becomes damaged, it must be repaired by an Authorized Service Centre or a
qualified person in order to avoid any hazard.
• Unplug from the socket outlet when not in use and before cleaning the appliance or undertaking maintenance operations
• Turn off the appliance before removing the plug. Do not pull on the mains lead, always pull on the plug body itself
• Do not handle plug or vacuum cleaner with wet hands.
• Do not use wet filters after wash, make sure they are completely dry to avoid damaging the cleaner.
• Do not vacuum flammable or combustible substances, neither use in areas where they may be present.
• Do not vacuum hot ash, embers or large and sharp objects.
• Do not vacuum water or other liquids.
• Keep the vacuum cleaner away from heat sources such as radiators, fires, direct sunlight, etc.
• This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the motor.
When this happens, disconnect the cleaner from the socket outlet and check the dust compartment and filters as they may be full or clogged
with line dust. Check for any other obstructions in the hose or tube. After removing the obstruction, leave the cleaner to cool down until the
thermal cut-out resets after approximately 60 minutes.
Page
................... 2
......................................... 4
.................................... 4
on the body of the fuse.
................................................................ 5
TYPE A
1
2
2
Page
....................................... 4
......................................... 5
...... 7
TYPE B
1
2

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Mc-cl483kMc-cl485k

Table of Contents