Preparation - Panasonic C9701U Operating Instructions Manual

Preparation

When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP] to change to regular mode.
1
Set your car's ignition switch to the ACC
or ON position.
The demonstration screen appears.
Example: CQ-C9901U
2
Press [DISP] (Display).
The demonstration screen is cancelled, and no more
appears.
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Insulation film
Battery Replacement
q Remove the battery holder
Tough pointed object
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
w Put a battery in the case with
(+) side facing up.
e Put the case back.
The following functions are activated when the Security
Function is ON. (a page 38)
¡ The security indicator blinks when removing the face
plate.
Security Indicator
12
CQ-C9901U/C9801U/C9701U
CS
SRC
Note: If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: Power) for 4 sec. or more after turning off the
power in other than the XM mode.
Warning
¡Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡
Remove and dispose of an old battery immediately.
¡ Do not disassemble, heat or short a battery. Do
not throw a battery into a fire or water.
¡ Follow local regulations when disposing of a
battery.
¡Improper use of a battery may cause overheat-
Back side
ing, an explosion or ignition, resulting in injury
or a fire.
Note:
¡Battery Information:
w Battery Type: Panasonic lithium battery (CR2025)
q
(Included in the remote control)
Battery Life: Approximately 6 months under nor-
2
mal use (at room temperature)
3
¡ The alarm sounds and the message appears on the
screen to warn you to remove the face plate at power
off.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡ Subwoofer level adjustment (a page 36)
¡ Subwoofer low pass filter (a page 36)
Connecting an XM Direct receiver
TM
Preparation:
¡ Connect the optional XM Direct TM receiver (XMD1000).
¡ To connect the XM Direct TM receiver (XMD1000), it is
required to use an optional extension cord (XMDPAN100)
that is produced by XM exclusively for Panasonic prod-
ucts.
Getting Started
It is required to sign up to become an XM Satellite Radio
subscriber. After checking your XM Satellite Radio ID,
sign up on the XM's website or by calling them.
1
Check of XM Satellite Radio ID
¡ Write down the ID indicated on the lower right of
your XM Direct TM receiver (XMD1000).
¡ Check the ID shown by tuning your XM Radio to
channel 0. (a page 30)
2
Activate the XM Satellite Radio
Select either of the below to sign up.
¡ Web site: http://www.xmradio.com/activation
¡ Phone number: 1-800-XM-RADIO (96-72346)
Note: Refer to the operating instructions for the XM
Direct TM receiver for details.
Note: Adjust the clock when "ADJUST" appears on the
display.
1
Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
for 2 sec. or more.
2
Press []] or [[] to display the DIS-
PLAY menu.
3
Press [ { ] to select "CLOCK ADJ".
4
Press [BAND] (SET) to confirm the dis-
play.
CQ-C9901U/C9801U/C9701U
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1
Press [SRC] (Source) to select the
AUX1 mode. (a page 16)
2
Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
for 2 sec. or more.
3
Press [BAND] (SET) to adjust.
: TV
: Other devices (Default)
Note: When using an external TV unit manufactured by
a third party, select the TV mode.
4
Press [MENU] to confirm the adjust-
ment.
5
Adjust the setting value.
[[]
: Adjusting minutes
[]] : Adjusting hours
[ } ]
: Forward
[ { ]
: Backward
6
Press [BAND] (SET) to confirm the
adjustment.
7
Press [MENU].
For using the remote control, hold down [MENU]
for 2 sec. or more.
13