Pioneer DEH-P4100 Installation Manual

DEH-P4100
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD3064-A/N> UC <99G00F0V01>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and • When this product's source is switched ON, a
negative grounding. Before installing it in a control signal is output through the blue/white
recreational vehicle, truck or bus, check the battery lead. Connect to an external power amp's system
voltage. remote control or the car's Auto-antenna relay
control terminal. (Max. 300 mA 12 V DC.) If the
• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning car features a glass antenna, connect to the antenna
booster power supply terminal.
installation.
• When an external power amp is being used with
• Refer to the owner's manual for details on
connecting the power amp and other units, then this system, be sure not to connect the blue/white
make connections correctly. lead to the amp's power terminal. Likewise, do not
• Secure the wiring with cable clamps or adhesive connect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tape of the auto-antenna. Such connection could cause
around them where they lie against metal parts. excessive current drain and malfunction.
• Route and secure all wiring so it cannot touch any • To avoid short-circuiting, cover the disconnected
moving parts, such as the gear shift, handbrake and lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a
seat rails. Do not route wiring in places that get
possibility of short-circuiting if the leads are not
hot, such as near the heater outlet. If the insulation
insulated.
of the wiring melts or gets torn, there is a danger of
• To prevent incorrect connection, the input side of
the wiring short-circuiting to the vehicle body.
• Don't pass the yellow lead through a hole into the the IP-BUS connector is blue, and the output side
engine compartment to connect to the battery. This is black. Connect the connectors of the same colors
will damage the lead insulation and cause a very correctly.
dangerous short. • If this unit is installed in a vehicle that does not
• Do not shorten any leads. If you do, the protection have an ACC (accessory) position on the ignition
circuit may fail to work when it should. switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
• Never feed power to other equipment by cutting
operations. If this is not done, the vehicle battery
the insulation of the power supply lead of the unit
may be drained when you are away from the
and tapping into the lead. The current capacity of
vehicle for several hours. (Fig. 1)
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• The black lead is ground. Please ground this lead
separately from the ground of high-current
products such as power amps.
If you ground the products together and the ground
ACC position No ACC position
becomes detached, there is a risk of damage to the
products or fire.
• Speakers connected to this unit must be high-
power types with minimum rating of 45 W and
• Cords for this product and those for other
impedance of 4 to 8 ohms. Connecting speakers
products may be different colors even if they
with output and/or impedance values other than
have the same function. When connecting this
those noted here may result in the speakers catch-
product to another product, refer to the supplied
ing fire, emitting smoke, or becoming damaged.
Installation manuals of both products and
• If the RCA pin jack on the unit will not be used, do
connect cords that have the same function.
not remove the caps attached to the end of the con-
nector.
IP-BUS input (Blue)
Antenna jack
This Product
Multi-CD player
(sold separately) IP-BUS cable
Rear output
See the section "DFS Alarm
Installation".
Fuse holder
Brown
White/yellow
Fuse resistor
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red Fuse resistor
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
Black (ground)
To vehicle (metal) body.
Fig. 1
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using a
different amp (sold separately).
Front output
Connecting cords
with RCA pin plugs
(sold separately)
Fuse
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal.
(Max. 300 mA 12 V DC.)
System remote control
+
Front speaker
≠
White Gray
+
Front speaker
≠
White/black Gray/black
Left
Green Violet
+
Rear speaker
≠
Green/black Violet/black
+
Rear speaker
≠
<ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
+
Front speaker
≠
+
Front speaker
≠
Right
+
Rear speaker
≠
+
Rear speaker
≠
Fig. 2 Fig. 2