Advertisement
ORDERING REPLACEMENT PARTS
If you encounter any problems with this product or if your need to order replacement parts, contact the ICON
Fitness Lifestyle Ltd. office, or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Leeds
LS118JG
Tel: Country Code: 0345-089009
0345-089009
Fax: 0113-2411120
To help us assist you, please be prepared to give the following information:
¥ The MODEL of the product (WLSI71500)
¥ The NAME of the product (WESLO
¨
BODY FLEX weight system)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 18 of this ownerÕs manual).
WESLO is a registered trademark of ICON Health & Fitness, Inc.
Part No. 172311 R1200A Printed in USA
© 2000 ICON Health & Fitness, Inc.
Model No. WLSI71500
Serial No.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are
committed to providing
complete customer satisfaction.
If you have questions, or if
there are missing parts, we will
guarantee complete satisfaction
through our Customer Service
Department.
Please CALL:
0345-089009
Or WRITE:
Unit 4
Revie Road Industrial Estate
Revie Road
Leeds
LS118JG
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
BOD
F L E X
F L E X
USER'S MANUAL
WG7150
ª
Advertisement
Table of Contents
Related Manuals for Weslo Body Flex
Summary of Contents for Weslo Body Flex
-
Page 1: Ordering Replacement Parts
CAUTION Read all precautions and instruc- tions in this manual before using WG7150 WESLO is a registered trademark of ICON Health & Fitness, Inc. this equipment. Save this manual for future reference. Part No. 172311 R1200A Printed in USA © 2000 ICON Health & Fitness, Inc. - Page 2 35 or persons with pre-existing health problems. Read all instructions before using. WESLO assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
-
Page 3: Before You Begin
Base 5 3/4Ó Pad tem, the BODY FLEX will help you to achieve the spe- (see the front cover of this user's manual). Stabiliser 1/2Ó x 3/8Ó Spacer cific results you want. -
Page 4: Assembly
ASSEMBLY NOTES Assembly requires two people. Due to the size and ¥ Tighten all parts as you attach them, unless weight of the weight system, assemble it in the loca- instructed to do otherwise. tion where it will be used. THE FOLLOWING TOOLS (NOT INCLUDED) ARE ¥... -
Page 5: Not Tighten The Nylon Lock Nuts Yet
3. Press the 1 1/4Ó Inner Cap (57) into the Front Upright CABLE DIAGRAM (42). Attach the 1Ó Plastic Stop (64) to the centre hole in The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (66). Use the the Stop Bracket (63) with a 5/16Ó... -
Page 6: Adjustment
6. Press the Weight Tube Bumper (79) into the TROUBLE-SHOOTING AND MAINTENANCE lower end of the Weight Tube (80). Upper Ends of Weight Guides Insert the Weight Tube (80) into the stack of have Holes Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The Weights (25). - Page 7 ATTACHING THE LEG LEVER TO THE LOW 9. Press two 1 3/4Ó Inner Caps (44) into each of the PULLEY STATION Arms (46). To use the Leg Lever (29), the seat must be attached Apply lubricant to the lower axles on the Arm to the Front Upright (42), (see ATTACHING AND Frame (52).
-
Page 8: Cable Diagram
12. Attach a Large ÒUÓ Bracket (56) to one of the Arms ADJUSTMENT 61ÑLubricate (46) with a 3/8Ó x 2 1/2Ó Bolt (62), a 3/8Ó Flat Washer (9) and a 3/8Ó Nylon Lock Nut (21). The instructions below describe how each part of the weight system can be adjusted. Refer to the EXERCISE Lubricate a 5/16Ó... -
Page 9: Notes
16. Insert the end of the Long Cable (66) through the 27. Wet the ends of the Lat Bar (85) and insides of the indicated bracket on the Top Frame (67), and two remaining Handgrips (48) with soapy water. Bracket down through the indicated hole in the Top Slide the Handgrips onto the ends of the Lat Bar. - Page 10 20. Wrap the Long Cable (66) up around a 3 1/2Ó 23. Attach the Backrest (41) to the Front Upright (42) Pulley (15) (see inset drawing). Attach the Pulley with two 1/4Ó x 2 1/2Ó Screws (43) and 1/4Ó Flat and a Cable Trap (59) to the Narrow Swivel Washers (10).
- Page 11 REMOVE THIS PART IDENTIFICATION SHEET FROM THE MANUAL! 3/4" Inner Cap (34)Ð4 1" Round Cap (49)Ð4 1" Cover Cap (55)Ð2 This chart is provided to help identify the small parts used in assembly. Some parts come pre-assembled for shipping purposes; if a part cannot be found in the parts bags, check the system frame to make sure it hasnÕt come pre-assembled. The number in parenthesis below each part refers to the key number of the part.
- Page 12 1/4" Nylon Lock Nut (7)Ñ6 1/2" x 1/2" Spacer (65)Ñ2 5/16" x 1 1/2" Bolt (24)Ð2 5/16" x 2" Eyebolt (35)Ñ1 5/16" Jam Nut (2)Ð6 1/2" x 3/8" Spacer (51)Ñ2 3/8" x 1 3/4" Bolt (12)Ð8 1" Spacer (22)Ñ1 5/16" Nylon Lock Nut (3)Ð23 5/16"...