Vf Display; Vf Marker; User Box - Panasonic AJ-SPX800E Operating Instructions Manual

8-4 VF
8-4-1

VF DISPLAY

Items/ Adjustable
Data Saved Range
DISP NORMAL NORMAL: Display status constantly.
CONDITION HOLD HOLD:
– C U F E
DISP MODE 1 Set the DISP MODE.
2 Switch the camera's Warning/Message
indication. Please refer to [4-7-4 Display
3
Modes and Setting Changes/adjustment
Result Messages] for more information.
– C U F E
VF OUT Y Select the VF output.
NAM Y:
NAM: Output signal with the highest level
R
G
R:
B
G:
B:
– C U F E
VF DTL 0 Select the VF DTL.
Additionally enhance the DTL for the VF
:
3
signal. 0 setting is the same DTL as the
:
primary scan lines.
– C U F E
5
ZEBRA1 0% Set the ZEBRA1 detection level (IRE value).
DETECT :
70%
:
– C U F E 109%
ZEBRA2 0% Set the ZEBRA2 detection level (IRE value).
DETECT :
85%
:
– C U F E 109%
ZEBRA2 ON Set the ZEBRA2 to ON, OFF, or SPOT.
SPOT
OFF
– C U F E
LOW LIGHT LVL OFF Set the camera incoming light volume at
which to display LOW LIGNT.
10%
15%
20%
25%
30%
35%
– C U F E
ECU MENU ON Set the menu display on the VF to ON or
DISP. OFF OFF when the ECU is connected.
– C U F E
50M ON Set the 50M recording indication to ON or
OFF.
INDICATOR OFF
– C U F E
MARKER/CHAR 50% Adjust the brightness of markers and
characters displayed on the VF.
LVL 60%
70%
80%
90%
100%
– C U F E
100
Remarks
Display status only when the
MODE CHECK switch is pressed.
Brightness signal
among R, G, and B signals.
Rch signal
Gch signal
Bch signal
8-4-2

VF MARKER

Items/ Adjustable
Data Saved Range
TABLE A Select the VF MARKER setting table.
B First, select table A or B, then set the items
below for each table.
– C U F E
CENTER MARK OFF Switch the centre mark.
1 OFF: Do not display centre mark.
1:
2
2:
3
3:
4
4:
– C U F E
SAFETY ZONE OFF Select the frame type for the safety zone.
OFF: Do not display frame.
1
1:
2
2:
– C U F E
SAFETY AREA 80% Set the position of the safety zone.
:
90%
:
– C U F E
100%
FRAME SIG 4:3 Set the frame marker.
Only enabled when REC MODE is set to
13:9
16:9.
14:9
The VISTA ratio is 16:8.65.
VISTA
– C U F E
FRAME MARK ON Set the frame marker to ON or OFF.
OFF
– C U F E
FRAME LVL 0 Set the level outside the frame marker.
: 0:
15
15:
– C U F E
8-4-3

USER BOX

Items/ Adjustable
Data Saved Range
USER BOX ON Select whether or not to display the USER
BOX.
OFF
– C U F E
USER BOX 1 Set the width of the USER BOX.
WIDTH :
13
:
100
– C U F E
USER BOX 1 Set the height of the USER BOX.
HEIGHT :
13
:
– C U F E 144
USER BOX H –50 Set the horizontal position of the USER
POS : BOX.
+00
:
– C U F E +50
USER BOX V –144 Set the vertical position of the USER BOX.
POS :
+000
:
– C U F E +144
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
+ (large)
Hollow (large)
+ (small)
Hollow (small)
Box
Corner frame
Equivalent to signal OFF.
Same brightness as centre area.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
Remarks