Remote Control And Its Functions - Toshiba RAS-18UFHP-ES Owner's Manual

REMOTE CONTROL AND ITS FUNCTIONS

1 Infrared signal emitter 1 1
1 1
Transmits a signal to the indoor unit.
2 START/STOP button 2 2
2 2
Press the button to start operation.
(A receiving beep is heard.)
Press the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor unit,
press the button twice.
3 3 Mode select button (MODE) 3 3 3
Press this button to select a mode.
Each time you press the button, a mode is
selected in a sequence that goes from A : Auto
changeover control,
: Heat,
(A receiving beep is heard.)
4 Temperature button ( 4 4
4 4
, ....... The set temperature is increased up to 30 °C.
9 ....... The set temperature is dropped down to 17 °C.
(A receiving beep is heard.)
5 5 5 5 Fan speed button (FAN) 5
Press this button to select fan speed. When you
select AUTO, the fan speed is automatically
adjusted according to the room temperature.
You can also manually select the desired fan
speed from among five settings.
(LOW , LOW
MED +
(A receiving beep is heard.)
6 6
6 Auto louver button (SWING) 6 6
Press this button to swing the louver.
(A receiving beep is heard.)
Press the FIX button to stop the louver swinging.
(A receiving beep is heard.) (
7 7
7 7 Set louver button (FIX) 7
Press this button to adjust the air flow direction.
(A receiving beep is heard.)
While this button is kept depressed, the receiving
tone continuously sounds. (
8 8
8 Off timer button (OFF) 8 8
Press this button to set the OFF timer.
9 9 9 On timer button (ON) 9 9
Press this button to set the ON timer.
! !
! Reserve button (SET) ! !
Press this button to reserve time settings.
(A receiving beep is heard.)
" "
" " Cancel button (CLR) "
Press this button to cancel ON timer and OFF
timer. (A receiving beep is heard.)
# # # High power button (Hi POWER)
# #
Press this button to start the high power
operation. (
Downloaded from AC-Manual.com Manuals
: Cool, : Dry,
: Fan only, and back to A.
)
+
, MED ,
, HIGH )
see page 13.)
see page 13.)
see page 15.)
$ $
$ $ $ Memory button (MEMO)
Press this button to stand by memorizing the
settings.
Press the button again for more than 3 seconds to
memorize the setting indicated on the remote
control and mark is indicated. (
% Automatic operation button (AUTO) % %
% %
Press this button to operate the air conditioner
automatically.
(A receiving beep is heard.) (
& & & & ECO timer button (ECO) &
Press this button to start the ECO timer (OFF
timer) operation.
You can select the OFF timer time from among
four settings (1,3,5 or 9 hours). (
( ( ( ( FILTER button (
Press this button to turn off the filter cleaning lamp
on the indoor unit.
Press this button after cleaning the air filter.
( see page 17.)
) ) ) ) PRESET button )
Press this button to operate the air conditioner
according to settings memorized by the MEMO
button. ( see page 12.)
~ ~
~ TIMER button ~ ~
Use this button to change the clock, ON timer, and
OFF timer times.
To forward the time, press the "TIMER
To set back the time, press the "TIMER
AUTOA
4 4
2 2
START/STOP
5 5
FAN
6 6
SWING
7 7
FIX
9 9
ON OFF
8 8
FILTER
16 16 16
4
see page 12.)
see page 15.)
see page 15.)
" button.
" button.
1
A
B
PRESET
13 17 13
3 3
14 14 14
AUTO
MODE
15 15 15
ECO Hi-POWER
12 12 12
TIMER
MEMO
13
17 17
SET CLR
11 11 11
10 10 10
RESET CLOCK CHECK
18 18 18
EN