Panasonic KX-FP70CX Service Manual page 65

11.1.3. Service Function Table
Code Function
501 Pause time set
503 Dial speed select
514 Bell detection time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
544 Document feed position adjustment
value set
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
567 T1 timer
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Set Value Effective
Range
X 100 msec 001~600
1: 10 pps 1, 2
2: 20 pps
X 100 msec 1~9
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~9 mm 1~9
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
1:ON 2:OFF 1, 2
X second 001~255
1:61% 2:67% 1, 2
X number of 00~99
times
X second 001~999
X number of 00~99
rings
X number of 00~99
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
65
Default
030
1
6
1 See Symptom/Countermeasure Table for long distance
and international calls in 12.3.2.1.5.The unit can copy,
but cannot either transmit/receive long distance or
international communications (P.94).
1 See Symptom/Countermeasure Table for long distance
and international calls in 12.3.2.1.5.The unit can copy,
but cannot either transmit/receive long distance or
international communications (P.94).
1 The resolution reverts to the default when transmission
is complete.
1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
5 When the ADF function is in correct, adjust the feed
position.
See 11.1.4.Memory Clear Specification (P.67).
See 10Test Mode (P.60).
2 See 10Test Mode (P.60).
1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
See 10Test Mode (P.60).
See 10Test Mode (P.60).
0 See 10Test Mode (P.60).
See 10Test Mode (P.60).
See 10Test Mode (P.60).
1 Sets whether or not to detect a paper jam. If a docu-
ment with a length longer than 600 mm is copied or
transmitted, the unit stops copying or transmitting as a
paper jamming because a document over 600 mm is
not normal. In the factory, transmitting or copying a doc-
ument longer than 600 mm is done as an aging test. In
this case, OFF is selected.
See 10Test Mode (P.60).
046
1 Sets the % break of pulse dialing according PBX.
05 Selects the number of times that ITS is redialed (not
including the first dial).
185 Sets the interval of ITS redialing.
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
185 Sets the FAX redial interval during FAX communication.
2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to
12.3.2.1.2.Sometime there is a transmit problem
(P.91).
KX-FP701CX/KX-FP702CX
Remarks
----------
----------
----------