Base Grille - Hotpoint CTX22D How To Get The Best

Use of adapter plug
Because of potential safety hazards
under certain conditions, we
strongly recommend against use of
an adapter plug. However, if you
still elect to use an adapter, where
local codes permit, a TEMPOWRY
properly grounded two-prong wall
(Fig. 2) available at most local
hardware stores.
I
TEMPORARY METHOD
(ADAPTER PLUGS NOT
ALIGN LARGE . ,
P /
RONGS SLOTS
%
AND FIRM CON
Fig. 2
BEFORE USE
The larger slot in the adapter must
be aligned with the larger slot in the
wall outlet to provide proper polarity
in the connection of the power cord.
CAUTION: Attaching an adapter
ground terminal to the wall outlet
cover screw does not ground the
appliance unless the cover screw is
metal, and not insulated, and the
wall outlet is grounded through the
house wiring. You should have
circuit checked by a qualified
electrician to make sure the outlet
is properly grounded.
When disconnecting the power
always hold
cord from the adapter,
the adapter with one hand. If this
is not done, the adapter ground
terminal is very likely to break
with repeated use.
Should the adapter ground
appliance until a proper ground
has again been established.
Use of etiension cords
Because of potential safety hazards
under certain conditions, we
strongly recommend against the
use of an extension cord. However,
if you still elect to use an extension
cord, it is absolutely necessary that
it be a UL listed 3-wire grounding
type appliance extension cord having
a grounding type plug and outlet
and that the electrical rating of the
cord be 15 amperes (minimum) and
120 volts. Such extension cords are
obtainable through your local
service organization.
The refrigerator should
always be plugged into ifi own
individual electrical outlet—
volt, 60 Hertz, or 100 volt,
(115
50 Hertz, single phase AC). This is
recommended for best performance
and to prevent overloading house
wiring circuits, which could cause a
fire hazard from overheating wires.
Refrigerator location
Install the refrigerator on a floor
strong enough to support it when
NECTION
it is fully loaded.
Do not install refrigerator where
temperature will go below 60°F.
because it will not run often enough
to maintain proper temperatures.
Also see Energy-Saving Tips
regarding location.
Clearances
Allow the following clearances
for ease of installation and proper
air circulation:
Sides. . . . . . . . . . . . . . . . . . . . 3/4"
Top . . . . . . . . . . . . . . . . . . . . . . 1"
Back. . . . . . . . . . . . . . . . . . . . . 1"
If refrigerator is to be installed
against a wall on the hinge side,
allow 1 'h" for door clearance.
Water supply to icemaker
will need to connect your
You
water supply kit containing copper
tubing, shutoff valve, fittings and
instructions is available at extra
cost from your dealer. There
should be sufficient tubing for the
to allow moving the refrigerator
out from the wall several feet
(approximately 3 coils of l/4-inch
copper tubing that measures at
least 10 inches in diameter).
.. Please Read Carefully.
4
Rollers
which enable
Adjustable rollers,
you to move the refrigerator away
from the wall for cleaning, are
located near the front corners of the
refrigerator. Set these rollers so the
refrigerator is firmly positioned on
the floor and the front is raised just
enough that the doors close easily
when opened about halfway.
turn the
To adjust the rollers,
raise the refrigerator, counterclock-
wise to lower it. Use a blade-type
screwdriver.
door closure, we recommend that
the bottom front edge of the cabinet
be approximately 3/4" from the floor.
You can turn the adjusting screws
through openings in the base grille.
I
I
grasp the bottom of the

base grille,

grille and pull it out.
To replace the base grille,
the clips on the back of the grille
with the openings in the baseplate
and push the grille forward until it
snaps into place.
II
I
lineup