Table of Contents
Advertisement
Quick Links
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
08457 089 009
Outside the UK: 0 (044) 113 387 7133
Fax: 0 (044) 113 387 7125
Please provide the following information when ordering replacement parts:
• the MODEL NUMBER of the product (WEEMSY60420)
• the NAME of the product (WEIDER
®
VIPER 2000 weight system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
centre of this manual)
Part No. 185502 R0902A
Printed in Canada © 2002 ICON Health & Fitness, Inc.
®
Model No.WEEMSY60420
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if there
are missing parts, please call:
08457 089 009
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: csuk@iconeurope.com
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Visit our website at
www.iconeurope.com
Advertisement
Table of Contents
Related Manuals for Weider WEEMSY60420
Summary of Contents for Weider WEEMSY60420
-
Page 1: Ordering Replacement Parts
Fax: 0 (044) 113 387 7125 USER'S MANUAL Please provide the following information when ordering replacement parts: Serial Number Decal (under seat) • the MODEL NUMBER of the product (WEEMSY60420) • the NAME of the product (WEIDER ® VIPER 2000 weight system) QUESTIONS? •... - Page 2 Note: A PART IDENTIFICATION CHART and a PARTS LIST/EXPLODED DRAWING are attached at the centre of this manual. Remove them before beginning assembly. Long Cable (66) High Pulley Station D—Weight Tube Short Cable (23) Low Pulley Station WEIDER is a registered trademark of ICON Health & Fitness, Inc.
-
Page 3: Important Precautions
TROUBLESHOOTING AND MAINTENANCE IMPORTANT PRECAUTIONS Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The WARNING: weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. To reduce the risk of serious injury, read the following important precautions before using the weight system. -
Page 4: Before You Begin
WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEY ing. The model number is WEEMSY60420. The serial op every major muscle group of the body. Whether PLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) -
Page 5: Assembly
ATTACHING THE LEG LEVER TO THE LOW ASSEMBLY PULLEY STATION To use the Leg Lever (29), the seat must be attached Before beginning assembly, carefully read the • Tighten all parts as you assemble them, unless to the front upright (see ATTACHING AND REMOV- ING THE SEAT on page 15). -
Page 6: Adjustment
3. Press the 1 1/4” Inner Cap (57) into the Front Single Hole ADJUSTMENT Upright (42). Attach the 1” Plastic Stop (64) to the centre hole The instructions below describe how each part of the weight system can be adjusted. IMPORTANT: When in the Stop Bracket (63) with a 5/16”... -
Page 7: Each Pedal With A 1/2" Tap Screw (6
30. Attach a VKR Armrest (99) to the Right VKR Arm 5. Press two 1 1/2” Bushings (93) into the Left Pedal (101) with two 1/4” x 2” Screws (102) and 1/4” (90); press two 1 1/2” Bushings (93) into the Flat Washers (10). - Page 8 9. Press the Weight Tube Endcap (79) into the indi- 26. Press a 1 1/2” Inner Cap (32) into the Seat Frame cated end of the Weight Tube (80). (36). Upper Ends of Weight Guides Insert the Weight Tube (80) into the stack of Insert a 1/4”...
-
Page 9: In The Same Manner
23. Hold the indicated end of the Short Cable (23) 12. Press two 1 3/4” Inner Caps (44) into each of the under the 3 1/2” Pulley (15) on the Front Upright Arms (46). (42). Attach the 5/16” x 3 1/2” Bolt (87), two 5/16” Flat Washers (8), the 1”... - Page 10 15. Attach the Wide Swivel Bracket (71) to the indi- 19. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4” cated bracket on the Top Frame (67) with a 5/16” Bolt (48), and 4 1/2” Pulley (77) from one end of x 3 1/4”...
- Page 11 REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL! 3/4" Round Inner Cap (34)–4 1" Round Inner Cap (49)–8 1" Round Cover Cap (55)–4 This chart is provided to help you identify the small parts used in assembly. Important: Some parts may have been pre-assembled for shipping purposes;...
- Page 12 1/4" Nylon Locknut (7)–6 1/2" Tap Screw (6)–2 5/16" x 2 3/4" Carriage Bolt (14)–3 1/2" x 3/8" Spacer (51)—2 1/4" x 3/4" Screw (18)–8 5/16" Jam Nut (2)–2 5/16" x 2 3/4" Bolt (11)–10 1/2" x 1/2" Spacer (65)—2 1/4"...
- Page 13 PART LIST—Model No. WEEMSY60420 R0902A REMOVE THIS PART LIST/EXPLODED DRAWING Key No. Qty. Description Key No. Qty. Description FROM THE MANUAL. 5/16” x 2 1/2” Carriage Bolt 1” Retainer 5/16” Jam Nut 1” Round Cover Cap 5/16” Nylon Locknut Large “U” Bracket Base 1 1/4”...
- Page 14 EXPLODED DRAWING—Model No. WEEMSY60420 R0902A 68 77 15 3 21 20...