Toro 74253 Setup Instructions
Hide thumbs
Also See for 74253:
- Operator's manual (64 pages) ,
- Operator's manual (60 pages) ,
- Service manual (272 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Z589 Z Master® Mowers
Model No. 74253—Serial No. 270002001 and Up
Model No. 74253CP—Serial No. 270002001 and Up
Model No. 74254—Serial No. 270002001 and Up
Model No. 74254CP—Serial No. 270002001 and Up
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
1
No parts required
2
No parts required
3
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, (3/8 x 1 inch)
4
Curved washer
Flange nut, (3/8 inch)
Bolt, (1/2 x 3–1/4 inch)
Flange nut, (1/2 inch)
5
No parts required
6
No parts required
Number 2 general purpose lithium
7
base or molybdenum base grease.
(Purchase separately.)
8
No parts required
9
No parts required
10
No parts required
Operator's Manual
Parts Catalog
Engine Owner's Manual
11
Registration Card
Safety Video
Key
© 2007—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
Register at www.Toro.com.
Form No. 3358-322 Rev A
Setup Instructions
Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the drive wheels.
1
1
1
8
Install the Rollover Protection
System (ROPS).
8
8
2
2
–
Add fuel to the machine.
–
Charge the battery.
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
Check the machine before delivery
–
to the customer.
1
1
1
Delivering the machine to the
customer.
1
1
2
Original Instructions (EN)
Use
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 74253
Summary of Contents for Toro 74253
-
Page 1: Setup Instructions
Form No. 3358-322 Rev A Z589 Z Master® Mowers Model No. 74253—Serial No. 270002001 and Up Model No. 74253CP—Serial No. 270002001 and Up Model No. 74254—Serial No. 270002001 and Up Model No. 74254CP—Serial No. 270002001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. -
Page 2: Checking The Tire Pressure
Step Step Removing Parts from the Raising the Machine Up and Crate Installing the Drive Wheels No Parts Required Parts needed for this step: Rear wheels Procedure Procedure Remove the tires and the parts for the ROPS from the shipping crate. 1. -
Page 3: Installing The Roll Over Protection System
Note: The curve washer cone must be installed toward the bolt head. Figure 4 4. Mount the wheels with the valve stem to the outside and secure them with the wheel nuts previously removed. 5. Torque the wheel nuts to 95 ft-lb (128 N·m). 6. -
Page 4: Adding Fuel To The Machine
6. Torque all lower fasteners, attached to the machine frame, to 30 ft-lb (41 N⋅m). 7. Tighten the center roll bar bolts (1/2 x 3-1/4 inch) so it rotates freely with some resistance. Note: No more than one thread should be exposed outside the nut. -
Page 5: Charging The Battery
Step Step Charging the Battery Checking the Machine for Grease No Parts Required Parts needed for this step: Procedure Number 2 general purpose lithium base 1 tube or molybdenum base grease. (Purchase separately.) Charging the battery produces gasses that Procedure can explode and cause serious injury. - Page 6 6. Check the grease for the pump drive belt idler arm. Figure 13 Figure 15 3. Check the tensioning arm for grease. 7. Check the grease for the PTO drive belt idler arm. 4. Check the grease for the three spindle bearings. If needed, add grease until it comes out of the lower seals.
-
Page 7: Checking The Engine Oil Level
Important: The grass deflector must be Step free to rotate with downward tension. Lift the deflector up to the full open position and ensure that it rotates freely,without binding into the full down position. Checking the Engine Oil Level No Parts Required Procedure Before you start the engine and use the machine, check the oil level in the engine crankcase;... - Page 8 Step Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
- Page 9 Step Delivering the Machine to the Customer Parts needed for this step: Operator’s Manual Parts Catalog Engine Owner’s Manual Registration Card Safety Video Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished.
- Page 10 Describe the post sale service procedures for your store. Assist the customer in lling out and mailing the registration card or register online at www.Toro.com Make sure that the customer receives the Operator’s Manual, Parts Catalog, Engine Owner’s Manual, Set Up Instructions, and safety video.