Service NR1601 / N1SG/N1B/U1B Manual Integrated Amplifier • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
RETURN Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Official Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set (Refer to "JIG FOR SERVICING".) When you update the firmware, you can use the following JIG (RS232C to internal connector conversion adapter with 4P FFC cable kit ).
Page 7
(Ref. No. of EXPLODED VIEW : 41) About the photos used for descriptions in the "DISASSEMBLY" section. • T he direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at the left of the respective photographs. • Refer to the table below for a description of the direction in which the photos were taken. • Photographs for which no direction is indicated were taken from above the product. • The Photographs is NR1601 N1B model. The viewpoint of each photograph Direction of photograph: B (Photografy direction) Front side [View from above] Direction of photograph: C...
1. FRONT PANEL ASSY Proceeding : CABINET TOP FRONT PANEL ASSY → (1) Remove the screws. View from bottom (2) Cut the wire clamp bands, then remove the screws. Direction of Direction of photograph: C photograph: D...
(3) Disconnect the connector wires and FFC cable. Remove the screws. CP303 FFC cable Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in FRONT PANEL ASSY. 2. RADIATOR ASSY Proceeding : CABINET TOP FRONT PANEL ASSY RADIATOR ASSY → → (1) Remove the screws. View from bottom...
Page 10
(2) Remove the screws. Direction of Direction of photograph: C photograph: D (3) Disconnect the connector wires. CP401 CP402 STYLE PIN:Loose RADIATOR ASSY PCB 7CH AMP Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in RADIATOR ASSY.
Page 11
3. PCB REG CNT/PCB REG Proceeding : CABINET TOP FRONT PANEL ASSY RADIATOR ASSY → → PCB REG CNT/PCB REG → (1) Remove the screws. PCB REG PCB REG CNT (2) Disconnect the connector wires and connector board. CP102 CP104 PCB REG CNT CP10 Direction of photograph: C PCB REG Board to board CP13A...
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY → (1) Cut the wire clamp bands, then disconnect the connector wire and FFC cable. FFC cable N2706 N2301 N2501 HDMI UNIT ASSY (2) Remove the screws, then remove the BACK PANEL. Direction of photograph: A (3) Remove the PCB RC-5/M-X. Board to board PCB RC-5/M-X...
Page 13
(4) Disconnect the connector board. Board to board Board to board Board to board PCB HDMI (5) Remove the screws. PCB AUDIO_VIDEO (6) Disconnect the connector wires. CP13A CP401 CP10 PCB SIDE CNT PCB AUDIO VIDEO PCB FRONT CNT...
Page 14
(7) Disconnect the connector board. PCB SIDE CNT PCB FRONT CNT Board to board Board to board PCB AUDIO VIDEO Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HDMI UNIT ASSY.
Page 15
5. PCB SPK/PCB SMPS Proceeding : CABINET TOP HDMI UNIT ASSY PCB SPK/PCB SMPS → → (1) Remove the Sheet, then remove the screws and SUPPORTER P.C. SUPPORTER P.C. Sheet View from bottom (2) Disconnect the connector wire, then remove the screws. Direction of photograph: D CX102...
Page 16
(3) Disconnect the connector wire, then remove the screws. Remove the PCB SPK/PCB SMPS from the main unit. CP402 CP403 CP405 (4) Disconnect the connector board. PCB SPK PCB SMPS Board to board...
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Firmware versions such as Main, Sub, DSP are displayed in SURROUND µcom/DSP Version display mode ENTER...
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "ENTER" and "SURROUND MODE" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2.
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When started up, the error information is displayed. Starting up: ●All model commonness With the "SURROUND MODE" and "BAND" buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set.
Page 20
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds. : T H E R M A L T H E Press and hold in the "ENTER"...
Page 21
3. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (U3103) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Official Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 23
(4) Connect the four extension jig cables. PCB HDMI Insulation sheet PCB FRONT CNT PCB SIDE CNT Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N2709 HDMI 25 pin SIDE CNT N2708 HDMI 19 pin CP105 FRONT CNT N2701...
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confirm contents of the following. After PWB Name Ref. No. Description Remark replaced DIGITAL U3102 R5F64169DFD SOFTWARE: Main DIGITAL U3301 R5F3650KNFB SOFTWARE: Sub DIGITAL U1903 EN29LV160BB-70TIP SOFTWARE: DSP ROM...
4. Run the DFW Run the “DFW_0002_NR1601_(Rev.1.0.6)” on desktop of PC. 5. Communication check (1) Click the “Check Comm.” button. (2) When connection is good, then you can see the “Communication check OK.” message. (3) If connection is not good, then you can see the “Communication check NG” message. Please confi...
6. Download the firmware (1) Click the "Load" button. (2) Download the firmware from the specified download source to PC. 7. Complete the firmware updating (1) Click the “Update” button. (2) When writing of the firmware is completed, the power of this unit turns on automatically and you can see the “Update completed”...
(i) In case of laptop PC, Use the AC adaptor. Confi rming the fi rmware’s number after upgraded After completion of the updating operation, the new version number can confi rmed by starting up the NR1601 according to the following procedure.
ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting • POWER (Power source switch) STANDBY...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, Is the fuse blown? Refer to 1.2.Fuse is blown. does the FLD on the front panel light? Check for damage Is a DC 5V voltage output in the SMPS B'D Is a DC 5V voltage being when the cord supplying the...
2. Analog video MONITOR OUT (CVBS) output NG Input COMPONENT Input CVBS Function : SAT Function : SAT To A Not output MONITOR OUT (COMPONENT) output NG Input COMPONENT Input CVBS Function : SAT Function : SAT To B Not output HDMI OUT outpu NG Input COMPONENT Input CVBS...
Page 35
Input CVBS Check power supply voltage. FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. HDMI B'D L2706 : H(5V) L2707 : L(0V) HDMI B'D flaw. L2708 : L(0V) L2710 : H(5V) L2711 : H(5V) Extend HDMI B'D using a jig.
Page 36
Input COMPONENT Check power supply voltage. FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. HDMI B'D HDMI B'D flaw. L2701 : H(3.3V) L2702 : H(3.3V) Extend HDMI B'D using a jig. Check power supply voltage.
Page 37
Check HDMI output setting, referring to the (5) Is the BD/DVD player's HDMI output setting correct? BD/DVD player's operating instructions. (6) When using a marantz BD/DVD player's, is the fluorescent display tube's "HDMI" indicator lit? If using a non-marantz BD/ DVD player's, proceed to "YES".
Page 38
BD/DVD player, is the FL HDMI connector (K1001/K1002/K1003/ from the HDMI connector display's "HDMI" indicator lit? K1004)15pin(DDC_CLK)/16pin(DDC_DATA)? (K1001/K1002/K1003/ If using a non-marantz BD/ Is 1pin/3pin/4pin/6pin/7pin/9pin/10pin/12pin of K1004) to the U1001 is DVD player, proceed to HDMI connector (K1501) terminated by 3.3V and defective.
Page 39
Check operation of each device. (AMP source : BD / Video input of player : 480P / Connect the TV.) Check operation of U1001. (18) Check power supply. Is 1.8V supplied to C1019/C1053/C1037/L1003? The power supply circuitry is defective. Is 3.3V supplied to C1112/C9032/C1124/C1122? (19) Check xtal oscillator.
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3 Check via AD.
Page 43
4.2. Power AMP (AMP B'D) No sound is output. The protector operates. Is the power transistor open or short circuit? Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. AV B'D CP8? Is the audio signal transmitted to The power amplifier is repaired. AV B'D CN401? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to AV B'D CP11?
Page 45
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK Wave form U1001 HDMI Rx ADV7840 CH1: D-DATA U1707 AUDIO PLD EPM3032ATC DIR/DIT U1706 LC89058W-E INPUT CH1: DATA COAXIAL-1 (2)RX0 SDIN(24) OPTICAL-1 (4)RX2 SLRCK(23) (42)SLRCK RMCK(16) (37)256fsDIR (9)RX5 RBCK(17) (3)64fsDIR RLRCK(20) (2)fsDIR CH2: fs RDATA(21) (44)DATADIR1...
Page 48
VCC BLOCK DIAGRAM MAIN +B S1(AMP +B) MAIN -B A+8.0V (Pre) 7808 DA+5.0V 7805 S2(+8V,-8V) 7908 A-8.0V (Pre) 2388F09 A.TUNER+9.0V(E2/E1C/J) 2388F05 A.TUNER+5.0V(E3) MAIN TRANS 7805 A.V+5.0V S4(VIDEO) 7905 A.V-5.0V -VKK S5(-VKK) FL AC (F1) AC CORD S6(FILAMENT) FL AC (F2) DV5.0V DV POWER1 3.3V...
Page 49
LAEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15220FP ANALOG H/POUT SPEAKER LINE IN GAIN ADJ. AK4358VQ AK5358B +30dB 4.34Vrms/8Ω SPK OUT FULL SCALE LEVEL=3Vrms AK4358VQ Headroom:2dB Config2(L/S/S/N)DOLBY LIMIT LEVEL=2.43Vrms (5.1ch-3dBFS at 30Hz) +20dB +20dB AK5358B 0dBFS=1.77Vrms +5dB +29dB 0dBFS=1.06Vrms - 24dB +10dB +10dB -10dBFS...
Page 50
LEVEL DIAGRAM CENTER ch R2A15220FP SPEAKER GAIN ADJ. AK4358VQ +30dB 4.2Vrms/8Ω SP OUT MAX SIGNAL LEVEL +20dB +20dB 0dBFS=1.77Vrms +29dB +10dB +10dB -10dBFS L.P.F GAIN=+1.6dB 213mVrms EXT IN -3dB DD INPUT:-20dBFS CNT 1kHz 200mV 200mVrms -20dBFS=177mVrms +1.6dB 95mVrms +4dB +4dB ANA INPUT:200mVrms L+R 1kHz 79mVrms +1.6dB...
Page 51
LEVEL DIAGRAM SUBWOOFER ch R2A15220FP MUTE PRE OUT GAIN ADJ. AK4358VQ +30dB 4. 74Vr m s SW ch DAC MAX SIGNAL LEVEL PRE OUT Config1(S/S/S/Y)DOLBY LIMIT LEVEL=2.5Vrms (5.1ch-3dBFS at 30Hz) +11dB AK4358VQ +20dB +20dB 0dBFS=1.77Vrms 1.37mVrms +8dB +10dB DD INPUT:0dBFS LFE 30Hz +10dB -10dBFS 4.74Vrms...
Page 52
LEVEL DIAGRAM SURROUND ch R2A15220FP SPEAKER GAIN ADJ. AK4358VQ D D SP +30dB 4.2Vrms/8Ω SP OUT MAX SIGNAL LEVE AK4358VQ +5dB +20dB +20dB 0dBFS=1.77Vrms +29dB +10dB +10dB -10dBFS L.P.F GAIN=+5dB 218mV -3dB 200mV 200mVrms -20dBFS=177mVrms +5dB DD INPUT:-20dBFS SURR 1kHz 125mVrms 98mV +4dB...
Page 53
LEVEL DIAGRAM SURR.BACK ch R2A15220FP SPEAKER GAIN ADJ. AK4358VQ +30dB 4.2Vrms/8Ω SP OUT AK4358VQ MAX SIGNAL LEVE +20dB +20dB 0dBFS=1.77Vrms +1.6dB +29dB +10dB +10dB -10dBFS L.P.F GAIN=+1.6dB EXT IN 200mV 200mVrms -20dBFS=177mVrms 150mV 150mVrms PRE OUT DD INPUT:-20dBFS SL+SR 1kHz +1.6dB (SB:MTRX ON, DD EX MODE) 67mV...
Page 81
TO DIR/PLD TO SUB CPU C9151 1000P C9152 1000P C9153 DA+5V DA+7V DA-7V 1000P C9154 1000P R2135 R2136 C9155 C9059 C9074 C9068 C9088 1000P OPEN OPEN OPEN OPEN C9073 C9093 DA+5V OPEN OPEN DGND DAGND A+7V C9078 C9098 DA+7V 0.1/10 A-7V OPEN OPEN...
Page 82
TO MAIN CPU NET3.3V DIGITAL NET1.8V SUPPLY DGND R2311 R2348 4.7K R2312 4.7K U2305 C2356 C2359 1/10 AK4424ET 1/10 C2360 JTAG 4.7/6.3 N2301 L2303 OPEN VSS2 BLM21PG221 TCKUSB R2332 CVDD MCLKUSB GND_D1 MCLK TDOUSB BCKoUSB BICK VSS1 DATAoUSB SDTI R2334 TMSUSB LRCKoUSB LRCK...
Page 84
TO DIGITAL SUPPLY L2813 OPEN SWM5V L2814 OPEN L2815 REMOTE3.3V OPEN SWM3.3V L2816 OPEN L2817 OPEN M3.3V L2818 OPEN L2819 OPEN N2708 L2820 OPEN 25P-SOCKET(C125Z2) L2721 OPEN D5V(MX) SWM5V(MX) SWM3.3V M3.3V DA+5V D/MGND DA+7V SIR_MO5/RDSDA L2790 OPEN SIR_MO/RDS_DATA DA-7V SIR_MI5/RDSCK L2791 OPEN SIR_MI/RDS_CLK...
Page 85
TO DIGITAL CONNECT R2925 R2926 OPEN OPEN R2927 R2928 OPEN DIGITAL SUPPLY SWM3.3V REMOTE3.3V N2901 SWM5V 4P-FFCs R2937 4.7K M3.3V DGND 232MO 232I_MO COMP.SDET 232MI 232O_MI Z1VSIG.DET Z1SSIG.DET R2902 CEC_POWER R2903 SR5005 OPEN DV_POWER2 DA_POWER DV_POWER1 232IMO3 DV_POWER1 DA_POWER 232OMI3 DV_POWER2 REMOTEPOWE R CEC_POWER...
B : Black model SG : Silver gold model 963402011980M PANEL FRONT(L) N1SG 3067214571210S Ref.No. Part No. Part Name Remarks Q'ty 963421006200M BADGE(MARANTZ) SILVER/GRAY 5630210678000S PCB 7CH_AMP ASSY 7025HK0928040 963416011990M WINDOW DISPLAY(ACRYL RED WINE) 5077212733010S PCB 7CH_AMP ASSY N1SG 7025HK0928030 963402011640M FRONT PANEL...
PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES zParts for which "nsp" is indicated on this table cannot be supplied. zPart indicated with the mark " ★ " is not illustrated in the exploded view. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 94
Ref.No. Part No. Part Name Remarks Q'ty 541010595006M INSTRUCTION MANUAL -2 N1B,N1SG 5707000004680S WARRANTY CARD 5727000000111S WARRANTY CARD (Canada) 5727041650142S ★ 12 90M-ZC000600R CORD ASSY N1B,N1SG L068250160020S ★ 12 90M-ZC000470R CORD ASSY L068125130010S 963531012030M BOX GIFT 6007211420010S BOX PAD 6240210840000S SHIPPING LABEL 5507000007000S LABEL COLOR...
Page 95
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI :U3102) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6...
Page 96
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST(U) O/L Terminal for SIRIUS control(U) 2 P95/(CLK4) HDRADIO RST/TU RST/ST IND O/L HDRADIO/TUNER KST-MW/KST-MT control 3 P94/(CTS4)/TB4IN RC IN O/(I) /M3.3 RC-5 input terminal 4 P93/(CTS3)/TB3IN FLASHER IN O/(I)
Page 97
Terminal for EEPROM control 90 P120/(TXD6) 91 VCC 92 P30/(A8) MIC DET SW3VPu O/L Terminal for MIC detection 93 VSS SOURCE DIRECT LED(NR1601) 94 P27/(A7) DIRECT LED /PURE DIRECT LED(SR5005)Control terminal(ON="H") 95 P26/(A6) O/L NC 96 P25/(A5) O/L NC 97 P24/(A4) STANDBY(CEC) LED O/L POWER LED control terminal(ON="H")/STANDBY(CEC) LED)
Page 98
Pin Name Synbol I/O Type Pullup STBY stop Function 126 P154/(TXD6) BT LINK SW3VPu O/L Bluetooth detection terminal 127 P153 USB PDN NET3VPu O/L USB(TELECHIPS) control terminal 128 P152/RXD7 129 P151/CLK7 130 VSS 131 P150/TXD7 132 VCC 133 P107/(AN7)/(KI3) ZVOL STB O/L ZONE VOL(NJW1194) control 134 P106/AN6/KI2 KEY3...
Page 100
R5F3650KNFB Terminal Functions Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 1 P94 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu DIR control pin (LC89058W-VF4A) 5 P90/CLK3 DIR CLK DIR control pin (LC89058W-VF4A)
Page 101
Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
LC89058W-E (HDMI : U1706) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK DGND LC89058W-E DV DD DV DD DGND GPIO0 RBCK RMCK GPIO1 AGND GPIO2 GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 104
Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND Digital GND MOUT...
Page 105
ADSP21367KSWZ2A (HDMI : U1901) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3...
Page 107
W9864G2IH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 108
W9864G2IH-6 Pin description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, A0−A10 Address A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 113
Signal Name Pin# Type Description – TCC8600 VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDADC PWR Analog Power for ADC (3.3V) VDDPLL PWR Analog &...
Page 114
Pin# Signal Name Type Description – TCC8600 XA[16] / SD_nRAS / ND_ALE External Bus Address Bit [16] / SDRAM RAS signal / ALE for NAND Flash XA[17] / ND_CLE External Bus Address Bit [17] / CLE for NAND Flash XA[18] / DQM[0] External Bus Address Bit [18] / Data I/O Mask 0 XA[19] / DQM[1] External Bus Address Bit [19] / Data I/O Mask 1...
Page 115
Pin# Signal Name Type Description – TCC8600 GPIO_D[17] GPIO_D[17] / I2C SCL GPIO_D[18] / UART1TXD GPIO_D[18] / UART1 TX Data. Internal pull-up resistor enabled at reset. GPIO_D[19] / UART1RXD GPIO_D[19] / UART1 RX Data. Internal pull-up resistor enabled at reset. GND Digital Ground GPIO_D[20] / UART1 RTS Output (active low).
PARTS LIST OF P.C.B. UNIT zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. Note: The symbols in the column "Remarks"...
Page 132
Ref. No. Part No. Part Name Remarks ETRO Q'ty OTHERS PARTS GROUP BKT1,2 BRACKET t1.0+Sn plating /PCB MTG 4010214876000S BKT101 BRACKET SCREW 4010210196000S CLAMP3 CLAMP WIRE(SOLDER) 4330000120000S CN,WIRE 230MM/5P L000231052050S CN,WIRE 670MM/2P L000671020050S CN,WIRE 2MM 170MM/10P L002171100050S CX102 CN.WAFER 7.92MM L108353280290S CX105 CN,WIRE 370MM/5P...
Page 133
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks ETRO Q'ty SEMICONDUCTORS GROUP IC103 00D2630553006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630553006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108 963239010770S IC NJM2388F09 N1G,N1SG J126238800090S...
Page 134
Ref. No. Part No. Part Name Remarks ETRO Q'ty C426 C,CERAMIC 0.1UF-K/50V D011104577160S C428-431 00D9630234205 C,ELECT 10UF-M/50V D040100087070S C436 C,CERAMIC 0.1UF-K/50V D011104577160S C437,438 C,CERAMIC 470PF-J/50V D010471167160S C441,442 C,CERAMIC 0.1UF-K/50V D011104577160S C445,446 C,CERAMIC 0.1UF-K/50V D011104577160S C470 C,CERAMIC 4.7UF-K/6.3V D011475571160S OTHERS PARTS GROUP BKT100 BRACKET SCREW 4010210196000S...
Page 135
PCB FRONT ASS'Y Ref. No. Part No. Part Name Remarks ETRO Q'ty SEMICONDUCTORS GROUP IC301 963239001880S IC AZ4580M J121458000020S z IC304 00D9600195808 IC ICP-N15 J120001500030S IC305 963239001880S IC AZ4580M J121458000020S Q300 00D9600133103 TR KSA916Y J5000916Y0050S Q301 00D9630120801 TR 2SC KRC102S (NB) J522010200210S Q302 00D9600285006 TR KRC104S (ND)
Page 137
PCB AUDIO_VIDEOASS'Y Ref. No. Part No. Part Name Remarks ETRO Q'ty SEMICONDUCTORS GROUP IC801 235810045600S IC R2A15220FP J084152200010S IC804 00D2623446900 IC TC4052BFT J040405205510S IC805 232810005504S IC BD7628F-E2 J127762800010S IC807,808 232810005504S IC BD7628F-E2 J127762800010S IC809 00D2623445901 IC TC4051BFT J040405105510S IC810 00D9630116307 IC LC74781-9013-E J170747810010S IC811 963239003470S IC NJM2586AM...
PCB HDMI ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP NOTE : U1001 IC ADV7840 J040784005510S When update Firmware, please confi rm a last U1501 963239010410S IC ADV7511BSTZ-225 J040751100010S version in SDI. U1703 00D2623077900 IC TC74VHCU04FT J040740405580S Use the service board after updating it.