Advertisement
Performance/ Specifications
General Specifications
NS12/NS10/NS8/NS5-V2
Item
Specifications
Rated power supply voltage
24 VDC
Allowable voltage range
20.4 to 27.6 VDC (24 VDC 15%)
Power consumption
25 W max. (15 W max. for the NS5)
Ambient operating temperature
0 to 50 C (See notes 1 and 4.)
Storage temperature
– 20 to 60 C (See note 2.)
35% to 85% (0 to 40 C) with no condensation
Ambient operating humidity
35% to 60% (40 to 50 C) with no condensation
Operating environment
No corrosive gases.
Noise immunity
Conforms to IEC61000-4-4, 2 kV (power lines)
Conforms to JIS C0040.
Vibration resistance
10 to 57 Hz, 0.075 mm amplitude, 57 to 150 Hz,
(during operation)
9.8 m/s
2
30 min each in X, Y, and Z directions
Shock resistance
Conforms to JIS C0041.
(during operation)
147 m/s
2
3 times each in direction of X, Y, and Z.
NS12: 2.5 kg max.; NS10: 2.3 kg max.;
Weight
NS8: 2.0 kg max.; NS5: 1.0 kg max.
Front operating panel: IP65F and NEMA4 compliant
Enclosure rating
(See note 3.)
5 years (at 25 C) Replace battery within 5 days
Battery life
after the battery runs low (indicator lights orange).
Applicable standards
cULus and EC directives
Note 1: The operating temperature is subject to the following restrictions according to the mounting
angle.
Mounting angle of 0 to 30 to the horizontal: Operating temperature range of 0 to 45 C
When a Video Input Unit or a Controller Link Interface Unit is mounted, the ambient operating
temperature is 0 to 35 C.
Mounting angle of 30 to 90 to the horizontal: See note 4.
Note 2: Operate the PT within the temperature and humidity ranges shown in the following diagram.
Storage
Operation
90
50
Temperature ( C)
40
30
30
20
10
0
Horizontal
—20
0
10
20
30
40
50
(0 )
Temperature ( C)
Note 3: May not be applicable in locations with long-term exposure to oil.
Note 4: •NS12/NS10/NS5
Mounting angle of 30 to 90 or less to the horizontal: Operating temperature range of 0 to 50 C
•NS8
Mounting angle of 30 to less than 90 to the horizontal: Operating temperature range of 0 to 45 C
Mounting angle of 90 to the horizontal: Operating temperature range of 0 to 50 C
NSH5-SQROOB-V2
Item
Specification
Rated power supply voltage
24 VDC
Allowable voltage range
20.4 to 26.4 VDC (24 VDC –15%/+10%)
Power consumption
10 W max.
Ambient operating temperature
0 to 40 C
Storage temperature
–20 to 60 C
Ambient operating humidity
35% to 85% with no condensation
Operating environment
No corrosive gases.
Common mode: 1,000 Vp-p (between power
supply terminals and panel)
Noise immunity
Normal mode: 300 Vp-p
Pulse width: 100 ns to 1 s, Rise time: 1-ns pulse
Vibration resistance
Conforms to JIS C0911.
(during operation)
Shock resistance
Conforms to JIS C0912.
(during operation)
Weight
1 kg max.
Enclosure rating
IP65 compliant
Ground
Ground to 100
or less.
Applicable standards
UL508 and EC directives
20
Characteristics
Display Specifications
Item
NS12-V2
NS10-V2
Display device
High-definition TFT color LCD
800 dot horizontal x
Number of dots
640 dot horizontal x 480 dot vertical
600 dot vertical
Display color
256 colors
Width 246.0 mm x
Width 215.2 mm x
Width 170.9 mm x
Display
Effective
height 184.5 mm
height 162.4 mm
height 128.2 mm
panel
display area
(12.1 inches)
(10.4 inches)
Left/right 60 ,
Left/right 60 ,
Left/right 65 ,
Field of vision
Top 45 , bottom 75
Top 35 , bottom 65
Top 50 , bottom 60
(See note 1.)
Service life
50,000 hours min.
(See note 2.)
Backlight
(See note
5.)
Brightness
There are 3 levels that can be set with the touch panel.
adjustment
Backlight error
Error is detected automatically, and the RUN
indicator flashes green as notification.
detection
Note 1: The bottom angle is 55 for V1 models.
2: This is the estimated time before brightness is reduced by half at room temperature
and humidity. It is not a guaranteed value. The service life will be drastically shortened
if PT is used at low temperatures. For example, using the PT at temperatures of 0 C
will reduce the service life to approximately 10,000 hours (reference value).
3: The brightness cannot be adjusted much.
4: This function does not indicate that the service life has been reached. It detects when
the backlight is not lit due to a disconnection or other errors. Backlight error detection
indicates that all backlights (2) are OFF.
5: Contact your nearest OMRON representative to replace the backlight.
Humidity (%)
95%
80%
Operating Specifications
60%
60
Item
Specification
40%
Method
Resistive membrane
35%
NS12-V2
1,900 (50 horizontal x 38 vertical) 16 x 16 dots for each switch.
20%
Number
Touch
NS10-V2
1,200 (40 horizontal x 30 vertical) 16 x 16 dots for each switch.
10%
panel
of
NS8-V2
768 (32 horizontal x 24 vertical) 20 x 20 dots for each switch.
(Matrix
switches
60
70
80
type)
NS5-V2/NSH5
300 (20 horizontal x 15 vertical) 16 x 16 dots for each switch.
Input
Pressure-sensitive
Service life
1,000,000 touch operations.
Data Capacity Specification
Series
Display device model
V 1
MQ (monochrome)
NS5
TQ (TFT)
SQ (STN)
6 MB
NSH5
SQ (STN)
NS8
TV (TFT)
20 MB
NS10
TV (TFT)
20 MB
NS12
TS (TFT)
20 MB
External Interface Specifications
Item
Specifications
Memory card
One ATA-Compact Flash interface slot.
interface
Used to transfer and store screen data and to store history data.
Expansion
For Expansion Interface Units
interface
Communications Specifications
Serial Communications
NS8-V2
NS5-V2/NSH5-V2
Item
TFT color LCD
STN color LCD
Port A
Monochrome LCD
320 dot horizontal x
240 dot vertical
Port B
Width 117.2 mm x
height 88.4 mm
Note: The 5-V outputs of serial ports A and B cannot be used at the same time.
(8.4 inches)
(5.7 inches)
TFT: Left/right 70 ,
Top 70 , bottom 50
Controller Link (Wired-type) Specifications
STN: Left/right 50 ,
Top 45 , bottom 50
Item
Monochrome:
Baud rate
Left/right 45 ,
Top 20 , bottom 40
Transmission path
TFT, STN: 75,000
hours min. (See
note 2.)
Ethernet Specifications
Monochrome:
Item
50,000 hours min.
(See note 2.)
Conformance standards
(See note 3.)
Video Input Specifications
(See note 4.)
Item
Resolution
Input signal
Cameras
USB Specifications
Item
USB rating
Connector
Compatible OMRON PLCs
CPU Units (1:1 NT Link Connection)
CQM1-CPU41-V1/CPU42-V1/CPU43-V1/CPU44-V1
V 2
CQM1H-CPU21/CPU51/CPU61
20 MB
CPM1-10/20CDR-
20 MB
CPM1A-10/20/30/40CD
20 MB
CPM2A-30/40/60CD
20 MB
CPM2C-10/20
60 MB
C200HS-CPU21/CPU23/CPU31/CPU33
60 MB
C200HE-CPU32(-Z) (See note 2.) /CPU42(-Z)
60 MB
C200HG-CPU33(-Z) (See note 2.) /CPU43(-Z) /CPU53(-Z) (See note 2.) /CPU63(-Z)
C200HX-CPU34(-Z) (See note 2.) /CPU44(-Z) /CPU54(-Z) (See note 2.) /CPU64(-Z) /CPU65-Z/CPU85-Z
CV500/1000/2000-CPU01-V1
CVM1-CPU01-V2/CPU11-V2/CPU21-V2
Note 1: Use an Adapter Cable (CPM2C-CN111 or CS1W-CN114/118), CPM1-CIF01 RS-232C Adapter, or CPM1-CIF11 RS-422A Adapter to connect.
2: A C200HW-COM02(-V1), C200HW-COM04(-V1), C200HW-COM05(-V1), or C200HW-COM06(-V1) Communications Board is required.
CPU Units (1:N NT Link Connection)
CS1G-CPU42H/CPU43H/CPU44H/CPU45H
CS1H-CPU63H/CPU64H/CPU65H/CPU66H/CPU67H
CS1D-CPU65H/CPU67H
CJ1G-CPU42H/CPU43H/CPU44H/CPU45H (See note 1.)
CJ1G-CPU42P/CPU43P/CPU44P/CPU45P
CJ1H-CPU65H/CPU66H/CPU67H (See note 1.)
CJ1M-CPU11/CPU12/CPU13/CPU21/CPU22/CPU23 (See note 1.)
CQM1H-CPU61/51 with a CQM1H-SCB41 Serial Communications Board
C200HE-CPU32(-Z) (See note 2.) /CPU42(-Z)
C200HG-CPU33(-Z) (See note 2.) /CPU43(-Z) /CPU53(-Z) (See note 2.) /CPU63(-Z)
C200HX-CPU34(-Z) (See note 2.) /CPU44(-Z) /CPU54(-Z) (See note 2.) /CPU64(-Z) /CPU65-Z/CPU85-Z
Note 1: The CJ1W-SCU21/SCU41 Serial Communications Unit can also be connected.
2: A C200HW-COM02/COM04/COM05/COM06(-V1) Communications Board is required.
Display Element Specifications
Specification
Conforms to EIA RS-232C.
D-Sub female 9-pin connector
5-V output (250 mA max.) through pin 6 (See note.)
Conforms to EIA RS-232C.
Display
D-Sub female 9-pin connector
text
5-V output (250 mA max.) through pin 6 (See note.)
Specification
2M/1M/500K
Shielded twisted-pair cable (special cable)
Text
attributes
Specification
Conforms to IEEE 802.3/Ethernet (10Base-T/100Base-T).
Flicker
Numeral units and scale settings
NS-CA001
NS-CA002
Alarm/event settings
320 x 240, 640 x 480, or 800 x 600 dots
User-defined size
Display colors
NTSC composite
NTSC composite video or PAL
video or PAL
CX-One Operating Environment
Number of cameras: 4 max.
2 cameras + RGB
Compatible OS
Recommended CPU
Specifications
Recommended memory
USB1.1
Hard disk free space
Type A (Host), Type B (Slave)
CD-ROM drive
Display
Note 1: CX-One OS precaution
Model number
+ CPM1-CIF01
-
+ CPM1-CIF01
-
+ CPM1-CIF01
-
(See note 1.)
Model number
Item
Specification
Raster font
Displayable characters
Base size
Alphanumeric characters
1 x 1, 1 x 2, 2 x 1,
Rough
8 x 8
or Japanese katakana
2 x 2, 3 x 3, 4 x 4, 8 x 8
Alphanumeric characters
Font
Standard
or Japanese, Chinese
8 x 16
1 x 1, 1 x 2, 2 x 1,
name
(Simplified, Traditional)
16 x 16
2 x 2, 3 x 3, 4 x 4, 8 x 8
or Korean
Alphanumeric characters
16 x 32
1 x 1, 1 x 2, 2 x 1,
Fine
or Japanese katakana
32 x 32
2 x 2, 3 x 3, 4 x 4, 8 x 8
Japanese kanji
Vector font
Can be specified in CX-Designer.
(text objects only)
Font, style, and size can be specified.
Color
256 colors
Font style (only when
Bold or italic
vector font is specified)
Vertical alignment
Top, center, or bottom
Horizontal alignment
Left-justified, centered, or right-justified
Functional
Up to 10 types can be registered.
Objects
objects
The flicker speed and flicker range can be set.
that can
Fixed
Select from 3 types.
flicker
objects
The flicker speed and flicker range are fixed.
1,000 max.
5,000 max.
256 colors max. (32,768 colors for BMP)
Windows 98 SE, Me, NT 4.0 (Service Pack 6a), 2000 (Service
Pack 3 or higher), or XP (See note 1.)
Pentium II 333 MHz or faster processor (Pentium III 1 GHz or
faster recommended.)
256 Mbytes min. (See note 2.)
Approx. 1.8 GB or more available space is required to install
the complete CX-One package.
Required for installation
SVGA (800 x 600) or better high-resolution display with 256 colors min.
The CX-One will not run on Microsoft Windows 95 or any other OS not listed above.
If such an OS is being used on the client computer, the OS must be upgraded before installing the
CX-One. System requirements and hard disk space may vary with the system environment.
2: The amount of memory required varies the Support Software applications used in CX-One.
Refer to use documentation for Individual Support Software for details.
Specifications
PLC model name
C-series CQM1
With RS-232C connector (9-pin type)
C-series CQM1H
C-series CPM1
Connect to peripheral port.
C-series CPM1A
Connect to RS-232C or peripheral port.
C-series CPM2A
C-series CPM2C
C-series C200HS
With RS-232C connector (9-pin type)
C-series C200HE (-Z)
C-series C200HG (-Z)
C-series C200HX (-Z)
CVM1/CV-series
With RS-232C connector (switching/9-pin type)
CVM1 or CV500/
CV1000/CV2000
Specifications
PLC model name
CS-series CS1G
CS-series CS1H
CS-series CS1D
CJ-series CJ1G
CJ-series CJ1G
CJ-series CJ1H
With RS-232C connector (9-pin type)
CJ-series CJ1M
C-series CQM1H
C-series C200HE(-Z)
C-series C200HG(-Z)
C-series C200HX(-Z)
21
Advertisement
