Advertisement
h Setting Time and Date [TIME]
If you have set the time and date, information as to when a sound file was recorded is stored
automatically with that file.
When you install batteries for the first time or each time you replace the batteries, the
"Hour" indication will flash. In such a case, be sure to set the time and date by following
steps 4 through 7 described below.
1 Press and hold the DISP/MENU button for 1
second or longer.
2 Press the + or – button to
select [TIME].
3 Press the PLAY ( ` ) but-
ton.
• The "Hour" indicator flashes.
4 Press the + or – button to
set the "Hour".
5 Press the PL AY ( ` ) or
9 button to accept the
"Minute".
• The "Minute" indicator flashes.
• Pressing the 0 button enables
the "Hour" setting again.
6 Press the + or – button to
set the "Minute".
• Repeat steps 5 and 6 to con-
tinue to set the "Year", "Month"
and "Date" in the same way.
7 After setting the "Date",
press the PLAY (`) or 9
button.
• This completes the time and date
setup procedure.
Notes:
• You can switch the time indication between the 12-hour system and the 24-hour system by
pressing the DISP/MENU button while you are setting the hour or minute.
• You can change the order of the date indication by pressing the DISP/MENU button while you
are setting the year, month, or day.
Example: July 14, 2008
Recording
1 Press the FOLDER/INDEX
button to select the desired
folder.
a Current microphone sensitivity
b Current folder
2 Press the REC (s) button
to start recording.
• The record/play indicator light
turns red, and recording starts.
c Current recording mode
d Current file number
e Recording level meter
f Recording time
3 Press the STOP (4) button
to stop recording.
• New recordings are saved as the
last file in the folder.
g Remaining recording time
a
b
c
d
e
f
g
-
3
-
h To Pause Recording
To Pause:
While the recorder is during recording mode, press
the REC (s) button
• [PAUSE] appears on the display and the record/play indicator
light flashes.
To Resume Recording:
Press the REC (s) button again.
• Recording will resume at the point of interruption.
h Notes for Recording
• If [FULL] appears on the display, you cannot record in the selected folder. In such a case, erase
unnecessary files.
• If the recorder is placed directly on a table when recording a meeting, it tends to pick up table
vibrations. Put a notebook or other item between the table and the recorder so that the vibration
is not easily transmitted for clearer recording.
• Even if you press the DISP/MENU button, the display will not change to current recording time
if the remaining recording time is 5 minutes or less.
• When remaining recording time is less than 60 seconds, the record/play indicator light starts
flashing in red. When the recording time is decreased to 30 or 10 seconds, the light flashes
faster.
• The recorder will enter Stop mode if it has been left paused for 60 minutes or longer.
• In case of difficult acoustic conditions or low speaker's voice, recording in [HQ] is recommended.
Also, usage of an external microphone (sold separately) could improve the quality of
recordings.
h Recording from external Microphone or other Devices
The external microphone and other devices can be connected
and the sound can be recorded.
• When using an external microphone, select adequate
Converting
microphone, such as a Noise-Cancellation microphone or
plug adapter
of KA333
Electret condenser microphone (optional).
A audio input
• To connect the recorder to an external device, use the
terminal of
connecting cord KA333 (optional), and the stereo/monaural
other devices
converting plug adapter supplied with KA333.
• The input level cannot be adjusted on this recorder. When
you connect the recorder to an external device, execute a test
recording and adjust the output level of the external device.
h LCD Display Information
You can select an option for the display of the recorder. This will help review and confirm different
recorder settings and file information.
State of the recorder
Operation
While in stop mode
Press and hold the STOP
(4) button
While in record mode
Press the DISP/MENU
button
While in stop mode or
Press the DISP/MENU
playback mode
button
Playback
1 Press the FOLDER/INDEX
button to select the de-
sired folder.
a Current folder
2 Press the 9 or 0 button to select the file
to playback.
3 Press the PLAY (`) button
to start playback.
• The record/play indicator light
turns green, and the elapsed
playing time is indicated on the
display.
b Current file number
c Playing time
Display
The total number of files recorded in the
folder and remaining recording time appears
on the display.
The display switches between current
recording time and remaining recording
time.
Playing time
Remaining playing time
Recording date of the file
Recording
time of the file
Playing time ...
a
b
c
-
4
-
Hide quick links:
Advertisement
