JUKI SC-910N Engineer's Manual
  1. Manuals
  2. Brands
  3. JUKI Manuals
  4. Sewing Machine
  5. SC-910N
  6. Engineer's manual
JUKI SC-910N Engineer's Manual

JUKI SC-910N Engineer's Manual

Hide thumbs Also See for SC-910N:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
®
SC-910N
ENGINEER'S MANUAL
40063908
No.E381-00

Advertisement

Table of Contents
loading

Related Manuals for JUKI SC-910N

Summary of Contents for JUKI SC-910N

  • Page 1 ® SC-910N ENGINEER’S MANUAL 40063908 No.E381-00...
  • Page 2 Instruction Manual. It is advisable to use the Instruction Manuals for IP-110, CP-170 and SC-910N and the relevant Parts Lists with this Engineer’s Manual when carrying out the maintenance of this sewing machine.

  • Page 3: Table Of Contents

    (4) Automatic compensation of neutral point of the pedal sensor ......68 (5) Selection of the pedal specifications ................ 68 7. CONNECTING PROCEDURE OF JUKI OPTIONAL DEVICE..... 69 (1) Connection of the bobbin thread remaining amount detection device (AE) ..69 (2) Connection of the material end sensor (ED) ............
  • Page 4 (1) Error code list (SC-910N) ................... 82 15. BLOCK DIAGRAM ..................85 (1) SC-910N block diagram (Rev. 01) ................85 (2) SC-910N block diagram (Rev. 02 and thereafter) ............. 86 (3) IP-110 operation panel block diagram ..............87 16. DRAWING OF THE TABLE (For DDL-9000A)........... 88...

  • Page 5: Specification

    4) By using the flash ROM for CPU, the future version-up can be adapted. 5) The SC-910N control box can be used for the (belt) drive system machine head by connecting the DD (direct-drive) system machine head and the small-sized motor unit (M-91).

  • Page 6: Name Of Each Component

    Operation panel (CP-170 or IP-110) Oil filler port (except for DDL-9000A-DS) Pulley cover Feed lever Thread stand Minute adjustable presser lifting screw Control box (SC-910N) Hand wheel Operation pedal Take-up lever cover One-touch type reverse feed button Finger guard Wiper...
  • Page 7 This cover protects the machine head motor. Thread stand Control box (SC-910N) The box contains the circuit that controls the head unit and motor, the output circuit that operates each output (the thread trimming solenoid, back solenoid, wiper solenoid, etc.), the pedal sensor that detects the pedal operation, and the power circuit that performs each function.

  • Page 8: Explanation Of Operation Panel

    4. EXPLANATION OF OPERATION PANEL (1) List of operation panels of CP-170 Description Power indication LED : Lights up when the power switch is turned ON. Max. speed limit variable resister : Maximum speed is limited when this resister is moved in the left direction ( Pattern selector switch : Used for selecting a pattern from among the four different patterns.

  • Page 9: List Of Operation Panel Of Ip-110

    (2) List of operation panel of IP-110 IP-110 Re-sewing switch Information switch Power display lamp Needle up/down compensating switch Material edge sensor switch Media slot cover Screen changeover switch One-shot stitching switch Media slot With/without reverse feed stitch With/without automatic thread (Media inserting opening) at sewing start switch trimmer switch...
  • Page 10 Teaching switch This is the switch to set the setting of the number of stitches with the value of number of stitches which has been actually sewn. Information switch This is the switch to perform various function settings. Material edge sensor Rendered effective when the material edge sensor is installed on the machine.

  • Page 11: Operation Of The Connection Panel

    (3) Operation of the connection panel 1) Connecting procedure of CP-170 or IP-110 [Connection of the connector for CP panel] Exclusive connectors are prepared for connection of the connector for CP-170. Paying attention to the orientation of the connector, con- nect it to connector CN35 located on the circuit board.

  • Page 12: Explanation Of Operation Panel Cp-170

    (4) Explanation of operation panel CP-170 1) Reverse stitching pattern 1. Press reverse stitching pattern switch specify the reverse stitching pattern. 2. The reverse stitching pattern is selected, and the number of stitches and data on reverse stitching which have already been specified are shown on the panel.
  • Page 13 2) Constant-dimension stitching pattern 1. Press constant-dimension stitching pattern switch on the control panel to select the constant-dimension stitching pattern. 2. The constant-dimension stitching pattern is selected. Now, the predetermined number of stitches and the state of reverse stitching Sewing pattern function are shown on the control panel.
  • Page 14 3) Overlapped stitching pattern 1. Press overlapped stitching pattern switch specify the overlapped stitching pattern. 2. The overlapped stitching pattern is selected, and the number of stitches and data on overlapped stitching which have already been specified are shown on the panel. 3.
  • Page 15 4) Rectangular stitching pattern Sewing pattern 1. Press rectangular stitching pattern switch on the control panel to select the rectangular stitching pattern. 2. The rectangular stitching pattern is selected. Now, the predetermined number of stitches and other sewing data are shown on the control panel. 3.

  • Page 16: Example Of Application

    (5) Example of application 1) When the CP-170 is used together with the material end sensor (ED : optional), it can be used as a small edge-controller. (Method) Adjust the position to mark of the CP-170, turn ON material end sensor ON/OFF switch of the CP-160, and turn ON mark...
  • Page 17 2) Label attaching is performed by the automatic one-shot stitching with the CP-170 (Method) Select mark on the CP-170, and turn ON mark of the automatic one-shot stitching. (Explanation) Number of stitches at the section CD can be set up to 500 stitches. If the stitch length is 2 mm, it is possible to sew approximately 1,000 mm (1 m).
  • Page 18 Section of EBT the rotating speed at the section where the sewing machine is rotated at a low speed can be changed. Section of low speed SC-910N function setting No. 64 Time Example) Use for reference. Standard Condition Machine head of DDL-9000A-SH (for thick materials)

  • Page 19: Explanation Of Operation Panel Ip-110

    (6) Explanation of operation panel IP-110 1) Reverse stitching pattern Press to display the pattern list screen. Sewing pattern 1. Press switch to select the reverse stitching pattern, and the screen is automatically changed over to the number of stitches reverse stitching setting screen to display the number of stitches which has already been set. 2.
  • Page 20 2) Overlapped stitching pattern Press to display the pattern list screen. 1. Press switch to select the overlapped stitching pattern, and the screen is automatically changed over to the number of stitches of overlapped stitching setting screen to display the number of stitches which has already been set.

  • Page 21: Information

    1) Information Setting and checking of various data can be performed with the information. For the information, there are the operator level and the maintenance personnel level. [Operator level] 1. Turn ON the power. 2. Press switch to display the information screen. Information screen (operator level) : Sewing management information...
  • Page 22 [Maintenance personnel level] 1) Turn ON the power. When the needle bar is not in the UP position, turn the handwheel to bring the needle bar to its UP position. 2) Press switch for approximately three seconds to display the information screen. 3) Press switches corresponding to the various functions.
  • Page 23 3. Sewing management information For the sewing management information, there are the operator level and the maintenance personnel level. [Operator level] Press switch in the information screen. (Previous page) [Maintenance personnel level] Press switch for approximately three seconds in the information screen. (Previous page) Pictograph on the left end of the sewing management information is shown in reverse video.
  • Page 24 5. Error record display Press error record display switch in the sewing management information screen (maintenance personnel level). (Refer to the previous page.) Error record screen When switch is pressed, the error record scrolls up or down. Explanation of display Record No.
  • Page 25 Operating procedure [Maintenance personnel level] Press communication mode switch for approximately three seconds in the information screen. Refer to [Information screen (Maintenance personnel level) Pictograph on the left end of the communication screen is shown in reverse video. Communication screen (Maintenance personnel level) Kind of selected data Data selection Data...
  • Page 26 Select the method to perform communication and press set key switch Reference : Communication method cannot be selected by downloading of program. 3 Data communication source 4 Data communication destination Set data communication source and data communication destination in the ten key screen, or "+" or "– "...
  • Page 27 8. All sewing machine data 1. Data such as sewing setting data, adjustment data, etc. which are memorized in the sewing machine can be stored in one package. 2. It is possible to download the all sewing machine data to the other sewing machines to make the same setting.
  • Page 28 Download : • Downloading of SC-910N program data Downloading from the compact flash (TM) is read from the folder of "PROG¥SC-910N". Store the copy from other media the like in the folder of "PROG¥SC-910N". 1 Create folder "PROG" in the compact flash (TM).
  • Page 29 10. Compact flash (TM) format Perform formating of the compact flash (TM). The compact flash (TM) formated with the personal computer or the like may not be used. When using the media with IP-110, be sure to perform formating with IP-110. Press compact flash (TM) format switch in the information screen (maintenance personnel level) Compact flash (TM) format confirmation screen...

  • Page 33: Warning List

    3) Warning list Contents and display of warning Corrective measure Remarks A201 Replacement of oil warning • Press to close warning screen, and Refer to the relevant perform replacement of needle. Then clear screen in regard to the value in the clear screen. the maintenance •...

  • Page 34: Control Box (Sc-910N)

    5. CONTROL BOX (SC-910N) (1)Connecting the cords WARNING : • To prevent personal injury caused by abrupt start of the sewing machine, carry out the work after turning OFF the power switch and a lapse of 5 minutes or more.
  • Page 35 Following connectors are prepared on the front face of SC-910N. Connect the connectors coming from the machine head to the corresponding places so as to fit the devices mounted on the machine head. 1. Method of connector connections (Rev. 01)

  • Page 36: Operating Procedure

    (2) Operating procedure 1. Press ON button of the power switch to turn ON the power. (Caution) When the power display LED does not light up even when the power switch is turned ON, immediately cut OFF the power and check the voltage. In addition, re-turn ON the power switch in such a case when 5 minutes or more have passed after turning OFF the power switch.
  • Page 37 6. When operation panel is connected, various sewing patterns such as reverse feed stitching at sewing start, reverse feed stitching at sewing end, etc. can be set. Refer to the Instruction Manual (CP-170 or IP-110) for the operation panel for the details. 7.

  • Page 38: Explanation Of The Operation Panel

    (3) Explanation of the operation panel switch : Used for determining the contents of setting. When this switch is pressed, flashing stops and the contents of setting are determined. switch : Used for changing the contents of setting. When this switch is pressed, changeable positions flash on and off. By pressing the switch, flashing position shifts in the right direction.

  • Page 39: Operating Procedure Of The Sewing Pattern

    (4) Operating procedure of the sewing pattern 1) Reverse stitching pattern Reverse stitching patterns below can be set by using the operation panel. Reverse stitching patterns that can be set Reverse stitching at start display Sewing pattern Revers stitching at end display [Setting procedure of the reverse stitching] Reverse stitching pattern Overlapped stitching pattern...
  • Page 40 5. Press switch to make number of Flash stitches display flash on and off, and set the num- ber of stitches for the respective processes of the stitching. 6. Press switch switch to change the number of stitches. The number of stitches can be changed up to as many as 15 stitches for the A, B, C, and D processes respectively.
  • Page 41 3) Special setting In addition to the normal function setting procedure at the front panel, it is possible to change the set value by directly moving to the function setting mode while the power is turned ON. [ Moving procedure to the function setting mode ] 1.
  • Page 42 (3) Number of stitches to stop the sewing machine after detection of material end setting (Function setting No. 4) Press switch to advance to the function setting No. 4. It is possible to change the set value with switch switch Specified number of stitches : 0 to 19 stitches (Caution) When the specified number of stitches is insufficient, there is a case where the sew-...

  • Page 43: Setting For Functions

    (5) Setting for functions Functions can be selected and specified by means of the four setting switches and light emitting diode located inside the front cover of the SC-910N. Specified No. Specified value Switch for entering specified value changed and updating setting No.
  • Page 44 4) Modification of functional setup Specified No. When you want to advance the setting No., press switch to advance the setting No. When you want to return the setting No., press switch to return the setting No. (Caution) When switch switch ) is held pressing, the setting No.

  • Page 45: Setting Procedure Of The Machine Head

    (6) Setting procedure of the machine head WARNING : When the machine head to be used is of the DDL-9000A (DS excluded), operation to be described below is needed to select the machine head type. Automatic setting is performed for the machine heads other than those of the DDL-9000A-DS and the DDL-9000A. Manual setting cannot be carried out.

  • Page 46: Machine Head List

    (7) Machine head list Number of revolutions at Max. number of Machine head Contents of display the time of delivery (rpm) revolutions (rpm) DLM-5400 4000 4500 DLN-5410 4000 5000 DLN-5410H 3500 4000 DMN-5420 4000 5000 DLD-5430 4000 4500 DLU-5490 4000 4500 DDL-5600B 3700...

  • Page 47: Adjusting The Machine Head (Ddl-9000A Only)

    (8) Adjusting the machine head (DDL-9000A only) WARNING : Be sure to perform the angle adjustment of the machine head by the operation below before using the machine head. 1. Simultaneously pressing switch switch , turn ON the power switch. is displayed (A) in the indicator and the mode is changed over to the adjustment mode.

  • Page 48: Function Setting List

    (9) Function setting list (Start level ; U : User’s mode, S : Service mode) Indication of Ref. Item Description Start level Setting range function setting page Soft start The number of stitches to be sewn at a low speed when the 0 to 9 function soft-start function is used at the start of sewing.
  • Page 49 Indication of Ref. Item Description Start level Setting range function setting page Sewing Counting function of sewing (number of completion of process) counter 0 : Sewing counter function is not operative. 1 : Sewing counter function is operative. Number of times Number of times of detection of run-out of bobbin thread 0 to 19 of detection of remaining amount...
  • Page 50 Indication of Ref. Item Description Start level Setting range function setting page Effective condition Effective condition of reverse feed stitching on the way of reverse feed 0 : Function is not operative when the sewing machine stops. stitching on the 1 : Function is operative when the sewing machine stops.
  • Page 51 Indication of Ref. Item Description Start level Setting range function setting page Compensation Compensation of starting the solenoid for reverse feed -36 to 36 of solenoid-on stitching when reverse feed stitching at the start of (10°) timing of reverse sewing is performed. feed stitching at the start of sewing...
  • Page 52 Indication of Ref. Item Description Start level Setting range function setting page On-timing of Starting (compensation) timing of solenoid for condensation -36 to 0 solenoid for stitch : -2 (10°) condensation Compensation value of starting the solenoid when stitch (when condensation stitch is performed by 2 stitches.
  • Page 53 Indication of Ref. Item Description Start level Setting range function setting page Function added Operation of needle up/down compensating switch is to needle up/ changed after turning ON the power or thread trimming. down compen- 0 : Normal (needle up/down compensating stitching only) sating switch 1 : One stitch compensating stitching is performed only when aforementioned changeover is made.
  • Page 54 Indication of Ref. Item Description Start level Setting range function setting page In-corner presser When the IP-110 is connected and a corner pattern is selected, ifter function this function is used to perform automatic presser rising after the completion of in-corner sewing. 0: OFF Automatic presser rising disabled after the completion of in-corner sewing 1: ON Automatic presser rising enabled after the completion...
  • Page 55 Indication of Ref. Item Description Start level Setting range function setting page Selection of When the IP-110 is connected, switch selection is performed 0 to 6 corner teaching to start in-corner sewing in the case of corner pattern sewing. start switch 0: No function 1: Left needle selector switch 2: Right needle selector switch...

  • Page 56: Detailed Explanation Of Selection Of Functions

    (10) Detailed explanation of selection of functions 1 1 1 1 1 Selection of the soft-start function (Function setting No. 1) The needle thread may fail to interlace with the bobbin thread at the start of sewing when the stitching pitch (stitch length) is small or a thick needle is used.
  • Page 57 7 7 7 7 7 Sound of click of the key switch mounted on the PSC box (Function setting No. 11) This function selects whether the sound is effective or ineffective when operating the four key switches mounted on the PSC box. 0 : off The sound of click is ineffective.
  • Page 58 0 0 0 0 0 Bird’s nest prevention function (Function setting No. 18 to 20, 28, 65, 66, 89, 100) This function prevents the thread from being entangled at the sewing start. This function is used only when it is combined with the sewing machine head with bird’s nest prevention specifi- cations.
  • Page 59 @ @ @ @ @ Function of changeover of compensating switch on the operation panel function (Function setting No. 22) Function of compensation switch on the operation panel of CP-170 or IP-110 can be changed over to needle up / down compensating stitching or one stitch compensating stitching. 0 : Needle up / down compensating stitching 1 : One stitch compensating stitching # # # # #...
  • Page 60 Actions under each setting state Function setting Output function Application No. 30 No. 32 No. 33 0 or 1 0 or 1 It works as normal touch-back switch. When operating touch-back switch at the time of depressing front part of the pedal, reverse feed stitching as many as the number of stitches specified by the function setting No.
  • Page 61 ( ( ( ( ( Adjustment of the pedal stroke (Function setting Nos. 39 to 44 and 48) No. 43 No. 48 No. 41 No. 42 No. 39 No. 40 No. 44 Low speed Speed in compliance with depressing amount of pedal section 11 12 13 14 15 (mm)
  • Page 62 6. Pedal stroke for reaching the maximum number of rotations (Function setting No. 44) Stroke between the pedal in its neutral position and the position where the sewing machine reaches at its highest speed can be adjusted. Adjusting range 1.0 to 15.0 [mm] <0.1 / mm> 7.
  • Page 63 3. Compensation of off-timing of solenoid for reverse feed stitching at the end of sewing (Function setting No. 53) Off-timing of solenoid for reverse feed stitching at the start of sewing can be compensated by the unit of angle. Adjusting range -36 to 36 <1 / 10°>...
  • Page 64 i i i i i Function of stop immediately after the reverse feed stitching at the start of sewing (Function setting No. 60) This function temporarily stops the sewing machine even when keeping depressing the front part of the pedal at the time of completion of process of reverse feed stitching at the start of sewing.
  • Page 65 d d d d d Retry function (Function setting No. 73) When the retry function is used, if the sewing material is thick and not piereced with needle, this function makes the needle pierce in the material with ease. 0 : Normal 1 : Retry function is provided.
  • Page 66 z z z z z Sewing counter input function (Function setting No. 101) This function can change over the count of the sewing counter displayed on the panel, when connecting IP-110 panel, whether to the external sewing counter switch input or to the automatic updating by the internal thread trimming count.
  • Page 67 , , , , , Test display mode function (Function setting No. 102) The I/O status can be examined at the CP panel. This function is valid only at the time of maintenance. Never use it in regular operation. The sewing machine can work normally. However, normal display cannot be presented at the control box or the CP panel.
  • Page 68 £ £ £ £ £ Re-sewing function (Function setting No. 109) When the IP-100 is connected, this function is used to stop/use the re-sewing function (sewing retried in the middle of operation). 0: off Re-sewing function disabled 1: on Re-sewing function enabled * Setting is possible only if LH-4168 or LH-4188 is selected for the machine head.
  • Page 69 ¶ ¶ ¶ ¶ ¶ Number of stitches for teaching replay (Function setting No. 113) The number of stitches is selected for teaching replay when corner teaching is carried out (measuring the num- ber of stitches for unilateral needle sewing). 0: The number of replay stitches coincides with that of measured stitches.
  • Page 70 ⁄ ⁄ ⁄ ⁄ ⁄ Selection of presser lifter switch function (Function setting No. 117) In the condition when the knee switch is connected, this function is used to select [stop or use] of the automatic presser lifter function by means of the knee switch. 0: off The automatic presser lifter is stopped with the knee switch.

  • Page 71: Changing Procedure Of The Pedal Type

    6. CHANGING PROCEDURE OF THE PEDAL TYPE (1) Parts necessary for change Part No. Description Q’ty M4009351000A Spring shaft B M4011351000 Return spring B M4012351000 Return pressure adjusting screw M2010110000 Return pressure adjusting nut (2) Attaching parts 1. Loosen return pressure adjusting nut in the pedal sensor A asm.

  • Page 72: Automatic Compensation Of Neutral Point Of The Pedal Sensor

    (4) Automatic compensation of neutral point of the pedal sensor Whenever the pedal sensor, spring, etc. are replaced, be sure to perform following operation : 1. Pressing switch , turn ON the power switch. 2. Indication on the screen will be as illustrated in .

  • Page 73: Connecting Procedure Of Juki Optional Device

    7. CONNECTING PROCEDURE OF JUKI OPTIONAL DEVICE (1) Connection of the bobbin thread remaining amount detection device (AE) When using the AE device, the optional IO p.c.b. is necessary. Connect solenoid cord attached to the side of the AE device to 2P plug (red) attached to the IO p.c.b.

  • Page 74: Connection Of The Pedal Of Standing-Work Machine (Pk)

    (3) Connection of the pedal of standing-work machine (PK) 1) Connect the connector of PK70 to connector (CN32 : 12P) of SC-910N. 2) Tighten the cord of PK70 together with other cords with cable clip band attached to the side of the box after passing it through the cable clamp.

  • Page 75: External Input / Output Connector

    Rotation speed is limited to the soft-speed while “L” signal is being inputted. DC5V, -5mA SGND — JUKI genuine part No. Connector : Part No. HK016510130 Pin contact : Part No. HK016540000 * Rev. 01 for CN42 – 71 –...

  • Page 76: Initialization Of The Setting Data

    9. INITIALIZATION OF THE SETTING DATA All contents of function setting of SC-910N can be returned to the standard set values. 1) Pressing all switches inside the front cover, turn ON the power switch. 2) LED displays indication with the sound “peep”, and initialization starts.

  • Page 77: Connector Connection Diagram

    No change Not used (Caution) 1. For the SC-910N, the connector number (CN**) may change according to the version. 2. Check the functional revision of the board and then insert it in the corresponding connector. 3. The descriptions in the next page and thereafter are applicable to the connector numbers of Rev.

  • Page 78: Solenoid For Machine Head

    (2) Solenoid for machine head 8 9 10 11 12 13 14 1 2 3 4 5 6 7 DDL-9000A-DS DDL-9000A-SS/MA/MS CN46 CN46 TRMD TRMD TRM (Thread TRM (Thread trimming) trimming) Ω Approx. 7.5 Ω Approx. 7.5 TRM COM TRM COM BT (Touch back) BT (Touch back) Ω...

  • Page 79: Optional Cord

    11. OPTIONAL CORD (1) Relay cord A asm. for the standing sewing machine (Part No. M9701351AA0) Approx. 1.5m 1) Wiring diagram of variable pedal PK-70 and -71 CN39 Brown Ω VR (1k Variable resistor Orange Used by variable voltage for speed between 1 to 2V Yellow (Increasing / decreasing...

  • Page 80: Relay Cord A Asm. For Dc24V (Part No. M9703351Aa0)

    2) Wiring diagram of fixing max. speed CN39 Brown Orange Variable resistor for speed Yellow S GND Green Switch for lifting presser foot Blue S GND Perple Switch for thread trimming Gray S GND White Switch for high-speed Light blue S GND Pink Switch for low-speed...

  • Page 81: Maintenance

    12. MAINTENANCE (1) Replacing the fuse 1) Grasp the glass part of fuses and remove them. 2) Use the fuse of which capacity is specified. : 3.15A/250V time-lag fuse (Power circuit protective fuses) Part No. KF000000080 – 77 –...

  • Page 82: Method Of Voltage Changeover

    (Caution) If the method of changeover is confused, the control box may be destroyed. Therefore, changeover actions must be taken carefully. 1) Replacement of the power cord 100V Change to JUKI authentic part number (M90355800A0) and the specifications earth cord (M90345800A0). 2) Changeover connector exchange The voltage changeover connector is mounted on the FLT board.

  • Page 83: Expansibility

    13. Expansibility If the parts specified below are added, the following models can be used: Item name Item No. Model Remarks DDL-5556N-7 I/O board (asm.) 40006077 LH-4168-7 LH-4188-7 KT-01 (EPF )Board set 40022484 DLU-5494N-7 ∗ ∗ For the DLU-5494N-7, select S (Standard) and procure the IP-110C separately. –...

  • Page 84: Regarding Error Display (Sc-910N)

    14. REGARDING ERROR DISPLAY (SC-910N) In case of the following, check again before you judge the case as trouble. Phenomenon Cause Corrective measure When tilting the sewing machine, the When tilting the sewing machine Tilt the sewing machine after turning...
  • Page 85 Before asking us for servicing, please examine the error codes. Checking procedure of the error code 1) Pressing switch in the control box (SC-910N), turn ON the power switch. 2) LED becomes display with the sound of “peep”...

  • Page 86: Error Code List (Sc-910N)

    (1) Error code list (SC-910N) Description of error detected Cause of occurrence expected Items to be checked E000 Execution of data initialization • When the machine head is changed. (This is not the error.) • When the initialization operation is executed...
  • Page 87 Description of error detected Cause of occurrence expected Items to be checked E811 Overvoltage • When voltage higher than guaranteed • Check whether the applied power voltage one is inputted. is higher than the rated voltage + (plus) 10% or more. •...
  • Page 88 MEMO – 84 –...

  • Page 89: Block Diagram

    15. BLOCK DIAGRAM Part name, asm. name Part No., asm. No. Circuit diagram number (1) SC-910N block diagram (Rev. 01) PANEL_PCB 40054669 40059015 FLT_S PCB A ASS’ Y 40058351 40058359 FLT_T PCB A ASS’ Y 40058361 40058369 RELAY_CORD_A_ASS’ Y 40058785 —...

  • Page 90: Sc-910N Block Diagram (Rev. 02 And Thereafter)

    (2) SC-910N block diagram (Rev. 02 and thereafter) Part name, asm. name Part No., asm. No. Circuit diagram number PANEL_PCB 40054669 40059015 FLT_S PCB A ASS’ Y 40058351 40058359 FLT_T PCB A ASS’ Y 40058361 40058369 RELAY_CORD_A_ASS’ Y 40058785 —...

  • Page 91: Ip-110 Operation Panel Block Diagram

    (3) IP-110 operation panel block diagram (TM) – 87 –...

  • Page 92: Drawing Of The Table (For Ddl-9000A)

    Depth : 10 3-ø13, Depth : 13 2-ø3.5, Depth : 10 Logo type, designated by JUKI 2-ø3.4, Depth at the rear side : 10 (Drill a hole at the time of set-up). X-X Section Rubber Installation Reference Figure Dimension Drawing in Detail (2:1) C1.5 to C2.5 (only for hinged section)
  • Page 93 <REFERENCE> TABLE OF DIGITAL DISPLAY Table of digital display Numeral Digital display Numeral Digital display Numeral Digital display Numeral Digital display...
  • Page 94 Juki Corporation operates an environmental management system to promote and conduct the following as the company engages in the research, development, design, sales, distribution,and maintenance of industrial sewing machines, household sewing machines, industrial robots, etc., and in the provision of sales and maintenance services...

Table of Contents