Page 30
Main IC Specifications - M13S128168A (ESMT) 2M x 16 Bit x 4 Banks Double Data Rate SDRAW - MT5111CE Single-Chip HDTV/CATV Demodulator - MT5351 MT5351 is a DTV Backend Decoder SOC which support flexible transport demux, HD MPEG-2 video decoder, MPEG1,2, MP3, AC3 audio decoder, HDTV encoder. MT5351 is powered by ARM 926EJ with 16K I-Cache and 16K D-Cache.
Page 31
TFT LCD Preliminary Specification MODEL NO.: V270B1 - L01 LCD TV Head Division 郭振隆 TVHD / PDD QRA Dept. DDIII DDII Approval Approval Approval Approval 陳永一 李汪洋 藍文錦 林文聰 LCD TV Marketing and Product Management Division 陳立宜 謝芳宜 Product Manager Version 1.0...
1. GENERAL DESCRIPTION 1.1 OVERVIEW V270B1- L01 is a TFT Liquid Crystal Display module with 14-CCFL Backlight unit and 1ch-LVDS interface. The display diagonal is 27”. This module supports 1366 x 768 WXGA format and can display true 16.7M colors(8-bits colors). The inverter module for backlight is built-in. 1.2 FEATURES - Excellent brightness (550 nits) - Ultra high contrast ratio (1000:1)
2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT Value Item Symbol Unit Note Min. Max. Storage Temperature ºC Operating Ambient Temperature ºC (1), (2) Shock (Non-Operating) (3), (5) Vibration (Non-Operating) (4), (5) Note (1) Temperature and relative humidity range is shown in the figure below. (a) 90 %RH Max.
2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE Value Item Symbol Unit Note Min. Max. Power Supply Voltage -0.3 Input Signal Voltage -0.3 2.2.2 BACKLIGHT UNIT Test Item Symbol Min. Type Max. Unit Note Condition Ta = 25 ℃ - -...
3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE Ta = 25 ± 2 ºC Value Parameter Symbol Unit Note Min. Typ. Max. Power Supply Voltage Power Supply Ripple Voltage Rush Current RUSH White Power Supply Current Black Vertical Stripe 1.65 Differential Input High +100 LVTH Threshold Voltage...
Note (3) The specified power supply current is under the conditions at Vcc = 5 V, Ta = 25 ± 2 ºC, f = 60 Hz, whereas a power dissipation check pattern below is displayed. b. Black Pattern a. White Pattern Active Area Active Area c.
3.2.2 INVERTER CHARACTERISTICS ( Ta = 25 ± 2 ºC) Value Parameter Symbol Unit Note Min. Typ. Max. Power Consumption (5), I = 4.7mA 22.8 25.2 Power Supply Voltage Power Supply Current Non Dimming Input Ripple Noise =22.8V Backlight Turn on 1790 Ta = 0 ºC Voltage...
Note (4) The life time of a lamp is defined as when the brightness is larger than 50% of its original value and the effective discharge length is longer than 80% of its original length (Effective discharge length is defined as an area that has equal to or more than 70% brightness compared to the brightness at the center point.) as the time in which it continues to operate under the condition Ta = 25 ±2℃...
Page 41
Note (2) The power sequence and control signal timing are shown as the following figure. Toff 2.0V BLON 0.8V Backlight on duration 2.0V Int. Dimming Function 0.8V Ext. Dimming Function PWMF PWMR 2.0V EPWM 0.8V 3.0V IPWM External External PWM Duty Period Minimun 100%...
5. INTERFACE PIN CONNECTION 5.1 TFT LCD MODULE CNF1 Connector Pin Assignment Pin No. Symbol Description Note Ground Display Rotation SELLVDS Select LVDS data format No Connection No Connection ODSEL Overdrive Lookup Table Selection EN LCS Low Color Shift Ground RX0- Negative transmission data of pixel 0 RX0+...
Page 44
5.2 BACKLIGHT UNIT The pin configuration for the housing and leader wire is shown in the table below. CN3-CN9 (Housing): BHR-03VS-1 (JST) Pin No. Symbol Description Wire Color High Voltage Pink High Voltage White Note (1) The backlight interface housing for high voltage side is a model BHR-03VS-1, manufactured by JST. The mating header on inverter part number is SM02(8.0)B-BHS-1-TB(LF) or equivalent.
5.3 INVERTER UNIT CN1(Header):S10B-PH-SM3-TB(D)(LF)(JST) or equivalent. Name Description +24V Power input Ground CN2(Header): S12B-PH-SM3-TB(D)(LF)(JST) or equivalent. Name Description +24V Power input Ground Internal/external PWM selection High : external dimming Low : internal dimming External PWM control signal E_PWM E_PWM should be connected to low when internal PWM was selected (SEL = low).
5.6 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input.
6. INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency 1/Tc Input cycle to LVDS Receiver Clock Trcl cycle jitter Setup Time Tlvsu LVDS Receiver Data...
Page 50
LVDS RECEIVER INTERFACE TIMING DIAGRAM RXCLK+/- RXn+/- Tlvsu Tlvhd 11 T Version 1.0...
6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below. Power Supply 0.9 V 0.9 V 0.1Vcc 0.1V ≦10ms 0≦T ≦50ms 0≦T ≦50ms 0≦T 500ms ≦T VALID Signals Power Off...
7. OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS Item Symbol Value Unit Ambient Temperature 25±2 Ambient Humidity 50±10 Supply Voltage Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" 4.7 ± 0.5 Lamp Current 56 ± 3 Oscillating Frequency (Inverter) 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 7.2.
Page 53
Note (1) Definition of Viewing Angle (θx, θy): Viewing angles are measured by EZ-Contrast 160R (Eldim) Normal θx = θy = 0º θy- θ θ 12 o’clock direction = 90º θx− θ = 90º θx+ 6 o’clock θ = 90º θ...
Page 54
Note (4) Definition of Luminance of White (L Measure the luminance of gray level 255 at center point and 5 points = L (5) = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at the figure in Note (7). Note (5) Definition of Cross Talk (CT): ×...
Page 55
Note (7) Definition of White Variation (δW): Measure the luminance of gray level 255 at 5 points δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)] Horizontal Line 3D/4 : Test Point...
8. DEFINITION OF LABELS 8.1 CMO MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. E207943 CHI MEI V270B1 -L01 Rev. XX MADE IN TAIWAN OPTOELECTRONICS X X X X X X X Y M D L N N N N (a) Model Name: V270B1-L01 (b) Revision: Rev.
10. PRECAUTIONS 10.1 ASSEMBLY AND HANDLING PRECAUTIONS (1) Do not apply rough force such as bending or twisting to the module during assembly. (2) It is recommended to assemble or to install a module into the user’s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer.