Advertisement
Quick Links
Advertisement
Related Manuals for Panasonic WV-Q126
Summary of Contents for Panasonic WV-Q126
-
Page 1: Operating Instructions
Operating Instructions Ceiling Mount Bracket WV-Q126 Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. -
Page 2: Table Of Contents
CONTENTS Preface ............................2 Precautions ..........................2 Major Operating Controls ......................4 Installations ..........................5 Specifications ..........................12 Standard Accessories ........................ 12 Preface This ceiling mount bracket is exclusively designed to mount the camera on a ceiling. Refer to the catalog or the installation guide of the camera for supported cameras. - Page 3 • Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the dealer for the inspections. • Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury.
-
Page 4: Major Operating Controls
Major Operating Controls Mounting chassis Camera mounting stage Decorative cover <Installation sample> Roof space Safety wire angle (Accessory) Safety wire (Accessory) Ceiling mount bracket Ceiling board Decorative cover Camera... -
Page 5: Installations
Installations Be sure to read "Precautions" before installation. The Installation Guide of the camera shall be read as well. Put Template A (accessory) against the * 1 The hole shape is shown below. ceiling and make a hole. Make 4 holes of 12 mm {1/2"} in diameter. Remove the center part from the tem- plate. - Page 6 3. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safe- ty wire (accessory) to the angle. Disconnect the safety wire from the Upper side Anchor bolt safety wire angle. Mark 2 Engage the face marked 1 with the anchor bolt.
- Page 7 5. Connect the mounting chassis to another tip of the safety wire. Roof space Safety wire (Accessory) Insert the mounting chassis into the hole Mounting chassis 6. Insert the mounting chassis into the hole made in Step 1. * [For those concerned with the direction of the brand logo] The direction of the logo on the decora- tive cover you installed in procedure 14 is...
- Page 8 7. Secure the mounting chassis to the 1st anchor bolt ceiling board with the ceiling board fixing screws (4 positions). Insert the anchor bolt Engage the top of the mounting chas- sis with the 1st anchor bolt. Double nuts Secure the mounting chassis by turn- ing the ceiling board fixing screws Ceiling board clockwise.
- Page 9 9. Attach the base unit or the camera Base unit mounting bracket to the camera mounting stage. Insert and tighten the 4 screws (M4, acces- sory) (Recommended tightening torque: 1.57 N m {1.16 lbf ft}) • • Note: • Which component to attach depends on the camera model.
- Page 10 10. Mount the camera mounting stage on Slots for the camera mounting stage flanges * 1 position on the rear side the mounting chassis. Insert the camera mounting stage Turn stopper flanges (3 flanges) into the flange slots * 2 positions (3 slots) in the camera mounting chas- on the rear side...
- Page 11 Connect the cables to the base unit or the camera. See the camera installation guide for infor- mation on how to connect the camera wires. 12. Mount the camera. Rotate Attach the camera to the base unit or the camera mounting bracket you Base unit attached in Step 9.
-
Page 12: Specifications
Specifications Ambient temperature: -10 C- + 50 C {14 F - 122 F} Dimensions: 245 mm {9-29/64"} in diameter x 188.8 mm {7"} in height (including the decorative cover) Weight: Approx. 1.2 kg {2.65 lbs.} Finish: Main body: Surface treatment steel sheet Decorative cover: ABS resin with silver metallic coating Standard Accessories Operating Instructions (this book) .......