Specific Safety Rules; General Safety Rules - Craftsman 315.115033 Operator's Manual

 When servicing a tool, use only identical re place ment parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to follow Main te nance Instructions may create a risk of
electric shock or injury.
 Hold tool by insulated gripping surfaces when per form ing an operation where the tool may con tact hidden
wiring or its cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the
operator.
 Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other
accessories running over rated speed can fly apart and cause injury.
Additional Rules For Safe Operation
 Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
 Always wear safety glasses. Everyday eye glass es
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the
risk of serious personal injury.
 Protect your lungs. Wear a face or dust mask
if the operation is dusty. Following this rule will
reduce the risk of serious personal injury.
 Protect your hearing. Wear hearing protection dur-
ing extended periods of operation. Fol low ing this
rule will reduce the risk of serious personal injury.
 Inspect tool cords periodically and, if dam aged,
have repaired at your nearest authorized service
center. Constantly stay aware of cord location.
Following this rule will reduce the risk of electric
shock or fire.
 Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will oper-
ate properly and perform its in tend ed func tion.
Check for alignment of mov ing parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly re paired or replaced by an authorized
service center. Fol low ing this rule will reduce the
risk of shock, fire, or serious injury.
 Do not abuse cord. Never carry the tool by the
cord or yank it to disconnect it from the re cep -
ta cle. Keep cord away from heat, oil, and sharp
edges. Following this rule will reduce the risk of
electric shock or fire.
 Make sure your extension cord is in good con-
di tion. When using an extension cord, be sure to

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

 Inspect for and remove all nails from lumber
 Drugs, alcohol, medication. Do not operate tool
 Save these instructions. Refer to them fre quent ly
4
use one heavy enough to carry the current your
prod uct will draw. A wire gage size (A.W.G.) of at
least 16 is recommended for an extension cord
100 feet or less in length. A cord exceeding 100
feet is not recommended. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
before sanding. Fol low ing this rule will reduce the
risk of serious personal injury.
while under the influence of drugs, alcohol, or any
medication. Fol low ing this rule will reduce the risk
of electric shock, fire, or serious personal injury.
and use them to instruct others who may use
this tool. If you loan someone this tool, loan them
these instructions also.
WARNING:
Some dust created by pow er sand-
ing, sawing, grinding, drilling, and other con-
struc tion activities con tains chem i cals known to
cause cancer, birth defects or other re pro duc tive
harm. Some examples of these chem i cals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other ma son ry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a
well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.