Setting Of Functions - Wolf SR 200.R10/1 User Manual

When operated as pulsing thermostat:
Text Basic setting Min. value
ProPortional band 3.0K
Width of PuLSe 5min

6. Setting of functions

By pressing „PROG" for 6 seconds you
reach a menu which ou can set various
basic functions in. The function is indicated
in the left part of
and the pertening value respectively the position is indicated in
the right part of the display. The value can be changed with +
and - keys. You reach the next choice with „SET". If you confirm
the last function with „SET" the thermostat goes back to the
operating mode out of which the menu „Setting of functions" has
been polled. The individual functions have the following meaning:
Text
SEnS (Sensor alignment)
Please do not align sensors immediately after
installation of the thermostat. as you need
temperature values which do not change too
much any longer. Moreover a sensor
alignment should be done at normal ambient
temperatures (approx. 20 °C).
In order to proceed with a correct sensor
alignment, the actual temperature indicated
by the thermostat as well as the temperature
at the sensor should be known (temperature
at the sensor must be measured by an
appropriate appliance).
between these two values can be set within
limits of ± 3.0K in menu point SEnS.
Example:
The thermostat indicates 20.7°C.
The thermometer indicates 19.9 °C
at the sensor.
The unit reading must be adjusted
by –0.8.
Max. value
1.0K 10.0K
1min 15min
MO DI MI DO FR SA SO
the display
Basic
setting
0.0 K
The difference
H C (Heating / Cooling)
In the mode „heating" the controlled relay is
indicated by an arrow upwards in the left
part of the display. In mode „cooling" the
relay is indicated by an arrow downwards.
2PPu (On/Off /Pulse)
Changing the control function from On/Off
to pulsing always leads to the appropriate
parameters
settings. These basic settings are indicated
bold print in menu point „setting of
parameter". If necessary these values have
to be changed as described before.
I E (Internal- / Remote sensor)
Limits/
If the remote sensor has been selected but
Alternative
there is no temperature sensor connectedI
± 3.0K
the display
thermostat does not control the output.
Loc (Keyboard lock)
The keyboard lock also prevents from
changing
temperature setback value with the knobs.
However, if the keyboard lock is deleted a
value for
temperature setback, which has been
changed in the meantime, is taken over.
You deactivate the keyboard lock if you
press „PROG" for 6 seconds.. An active
keyboard lock is indicated by a key symbol.
2PPu (On/Off /Pulse)
Changing the control function from On/Off
to pulsing always leads to the appropriate
parameters
settings. These basic settings are indicated
bold print in menu point „setting of
parameter". If necessary these values have
to be changed as described before.
I E (Internal- / Remote sensor)
If the remote sensor has been selected but
there is no temperature sensor connectedI
the display
thermostat does not control the output.
Loc (Keyboard lock)
The keyboard lock also prevents from
changing
temperature setback value with the knobs.
However, if the keyboard lock is deleted a
value for
temperature setback, which has been
changed in the meantime, is taken over.
You deactivate the keyboard lock if you
press „PROG" for 6 seconds.. An active
keyboard lock is indicated by a key symbol.
computing with the
indicates 65.0°C.
comfort value respectively
comfort temperature
computing with the
indicates 65.0 C.
comfort value respectively
comfort temperature
HE Co
(heating) (cooling)
2-P PuL
(On/OFF) (Pulsing)
basic
I E
(intern) (extern)
The
oFF on
(inaktiv)
(aktiv)
resp.
2-P PuL
(On/OFF) (Pulsing)
basic
I E
(intern) (extern)
The
oFF on
(inaktiv) (aktiv)
resp.
- 7 -