Bosch Uneo Maxx Original Instructions Manual page 13

OBJ_BUCH-1190-004.book Page 13 Wednesday, June 11, 2014 10:03 AM
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-6.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
Hammer drilling into concrete: a
h
2
Drilling into metal: a =4 m/s , K=1.5 m/s
h
2
Screwdriving: a <2.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
cluding their amendments and complies with the following
standards: EN 60745-1, EN 60745-2-6.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 18.06.2014
Bosch Power Tools
Assembly
 Before any work on the machine (e. g., maintenance,
Battery Charging (see figure A)
 Use only the chargers listed in the technical data. Only
2 2
=13 m/s , K=3 m/s ,
2
,
2
.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
To remove the battery 10, press the battery unlocking button
18 and pull the battery out of the power tool toward the rear.
Do not exert any force.
For charging, the battery 10 can also remain in the power
tool. During the charging procedure, the power tool cannot be
switched on. Press the On/Off switch 8 to check the charge
condition of the battery, see Section "Battery Charge-control
Indication".
Observe the notes for disposal.
Selecting Tools
For hammer drilling, SDS-Quick tools are required.
For drilling without impact in wood, metal, ceramic and plas-
tic, a suitable SDS-Quick tool or an application tool with hexa-
gon shank can be used.
For screwdriving, use only screwdriver bits with ball catch 14
(DIN 3126-E6.3). Other screwdriver bits 13 can be inserted
via a universal bit holder with ball catch 12.
A selection of suitable application tools can be found in the
Accessories Overview at the end of these instructions.
Changing the Tool
out at no-load. However, this has no effect on the accuracy of
the drill hole, as the drill bit centres itself during drilling.
The SDS-Quick tool holder can also accommodate different
drill-bit types with hexagon shank. For more information, see
the accessories page at the end of these operating instruc-
tions.
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
these chargers are matched to the lithium-ion battery of
your power tool.
machine has been automatically switched off. The bat-
tery can be damaged.
The SDS-Quick tool holder allows for simple
and convenient changing of drilling tools with-
out the use of additional tools.
Due to their working principle, SDS-Quick drill-
ing tools move freely. This results in radial run-
English | 13
1 609 92A 0R0 | (11.6.14)