Specifications - Shure BETA 87C User Manual

Proximity Effect
Unidirectional microphones such as the BETA 87C progres-
sively boost bass frequencies by 10 to 15 dB at 100 Hz when
the microphone is at a distance of about 6 mm (1/4 in.) from the
sound source. This phenomenon, known as proximity effect,
can be used to create a warmer, more powerful sound. To pre-
vent excessive or "boomy" low frequency sound during close-
up use, the BETA 87C bass response gradually rolls off. This
provides greater control and helps the user take advantage of
proximity effect.
Wind Noise
The BETA 87C has an integral wind and pop filter which pro-
vides excellent protection against most wind and breath noise.
Under adverse conditions, such as high winds or close proximity
to a "problem" vocalist, the optional foam windscreen can be used.
Impedance
A minimum load impedance of 800 ohms should be used for
maximum signal handling and minimum distortion. The load
may be as low as 150 ohms, but a reduction in output level and
output clipping level will result.

SPECIFICATIONS

Transducer Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz (see Figure 2)
TYPICAL FREQUENCY RESPONSE
FIGURE 2
Polar Pattern
cardioid (see Figure 3)
TYPICAL POLAR PATTERN
FIGURE 3
Output Impedance
Rated at 150 ohms (100 Ohms actual ±20%)
Recommended minimum load impedance: 800 ohms
Sensitivity (at 1,000 Hz)
Open Circuit Voltage
Output Clipping Level
1000 Ohm Load
at 1,000 Hz
Maximum SPL
139 dB at 1,000 Hz (0.25% THD, 1000 Ohm load)
Self-Noise
22 dB typical, A-weighted
24 dB typical, weighted per DIN 45 405
(equivalent sound pressure level; measured with true rms volt-
meter)
Dynamic Range
117 dB (maximum SPL to A-weighted noise level)
Hum Sensitivity
–5 dB equivalent SPL, maximum, in a 1 mOe field (60 Hz)
Signal-to-Noise Ratio
72 dB at 94 dB SPL (IEC 651)*
*S/N ratio is difference between 94 dB SPL and equivalent SPL of self–
noise A-weighted.
Polarity
Positive pressure on diaphragm produces positive voltage on
pin 2 relative to pin 3 of the output connector. See Figure 4.
BETA 87C BLOCK DIAGRAM
Power
Phantom Supply Requirement
Current Drain . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector
Three–pin (XLR) professional audio
Case
Aluminum construction with painted blue metallic finish, and
hardened steel grille with nickel satin chrome plating
Dimensions
See Figure 5
21 mm
53
( / in.)
64
OVERALL DIMENSIONS
Net Weight
Net: 207 grams (7.6 oz)
Packaged: 565 grams (1.24 lbs)
Environmental Conditions
° °
Operating: –18 to 60
° °
Storage: –29 to 74 C (–20
2
. . . . . . . . . . . . . . . –51 dBV/Pa (2 mV)
(1 Pa = 94 dB SPL)
. . . . . . . . . . . . . –6 dBV (0.5 V)
FIGURE 4
. . . . . 11 to 52 Vdc, positive
at both pins 2 and 3
1.0 to 1.2 mA
192 mm
9
(7– / in.)
16
FIGURE 5
° °
C (0 to 135 F)(relative humidity <90%)
° °
to 165 F) (relative humidity <80%)
51 mm
(2 in.)