Nordictrack user's manual grt 490 weight system 831.159760 (33 pages)
Summary of Contents for NordicTrack Revitalize 30792.0
Page 1
Model No. 30792.0 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or if parts are...
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the inversion table. 1. Read all instructions in this manual before using the inversion table. Use the inversion table only as described in this manual. 2.
To help us assist you, note the product model number and serial number before contacting us. The model number is 30792.0. The serial number can be found on a decal attached to the inversion table (see the front cover of this manual).
PART IDENTIFICATION CHART See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST on page 18. Note: Some small parts may have been pre- assembled.
ASSEMBLY Make Assembly Easier This manual is designed to ensure that the inversion table can be assembled successfully by almost anyone. However, the inversion table has many parts, and the assembly process will take time. Most people find that if they set aside plenty of time, assembly goes smoothly.
Page 7
2. Attach the Left Base (1) to the Right Base (2) with two M10 x 80mm Button Bolts (52), four M10 Curved Washers (50), and two M10 Nylon Locknuts (65). Attach another Foot (42) to the Right Base (2) with an M4 x 20mm Screw (71). 3.
Page 8
5. Attach the Center Base (3) to the Left and Right Bases (1, 2) with four M10 x 80mm Button Bolts (52), four M10 Curved Washers (50), and four M10 Nylon Locknuts (65). 6. See the inset drawing. Identify the Center Frame (7).
Page 9
8. Attach the Top Cover (23) and the Bottom Cover (24) to the Center Frame (7) with two M4 x 15mm Screws (58) and an M4 x 30mm Screw (63). Attach the Center Frame Extension (6) to the Center Frame (7) with two M10 x 53mm Button Bolts (49) and two M10 Nylon Locknuts (65).
Page 10
11. See the left inset drawing. Identify the Top Tube (16), the Bottom Tube (17), and the Ankle Brace Tube (18); the Tubes have differ- ent lengths and holes in different positions. Orient the Top Tube (16) and the Bottom Tube (17) so that the largest holes are on top (see the right inset drawing), and insert them into the indicated holes in the Leg...
Page 11
14. Identify the two Rear Ankle Braces (34), which have holes in the indicated locations. Slide a Rear Ankle Brace (34) onto the Ankle Brace Tube (18). Attach the Rear Ankle Brace with two M4 x 15mm Screws (58). Make sure that the Screws are tightened into the indi- cated holes in the Ankle Brace Tube.
Page 12
17. Attach the Headrest (20) to the Headrest Frame (9) with two M6 x 18mm Button Screws (55), an M6 x 55mm Button Screw (56), and three M6 Washers (62). Attach the Backrest (21) to the Backrest Frame (8) in the same way. 18.
ADJUSTMENT This section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 16 for impor- tant information about how to get the most benefit from the inversion table. Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts immediately.
Page 14
USING THE ANKLE LOCK To secure your ankles in the inversion table, pull the Lock Handle (33) out as far as it will go, and move the Lock Frame (11) away from the Leg Frame (10). Stand on the Foot Plate (19), with the backs of your legs against the Rear Ankle Braces (34).
ROTATING ON THE INVERSION TABLE This section explains how to rotate back on the inversion table, and then return to the starting position. Before using the inversion table, see the ADJUSTMENT section starting on page 13 to correctly set up the inversion table.
DEVELOPING A PROGRAM This section contains information and suggestions about using the inversion table. Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts immediately. See the ADJUST- MENT section starting on page 13 to identify parts referred to in this section. BENEFITING FROM USING THE INVERSION TABLE If you feel nauseated while using the inversion table, return to the starting position.
PART LIST—Model No. 30792.0 Key No. Qty. Description Left Base Right Base Center Base Left Frame Right Frame Center Frame Extension Center Frame Backrest Frame Headrest Frame Leg Frame Lock Frame Handle Support Leg Base Support Bracket Top Tube Bottom Tube...
• the MODEL NUMBER of the product (30792.0) • the NAME of the product (NordicTrack REVITALIZE INVERSION SYSTEM inversion table) • the SERIAL NUMBER of the product (see the front cover of this manual) •...