Table of Contents
Advertisement
Main Menu
(continued)
VIDEO CONFIG
Sub menu
Settings
GAMMA
<NORMAL>
*2
SELECT
<FILM>
*2
<VARICAM>
FILM GAMMA
<OTHER>
COLOR TEMP.
<USER0–63>
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
SHARPNESS
<HIGH>
*2
<LOW>
MODE
*2
<0–30>
SHARPNESS H
*2
<0–30>
SHARPNESS V
*2*6
<MODE2>
I-P MODE
<MODE1>
*2
<OFF>
MONO
<ON>
*2
<OFF>
ANAMO
<ON>
*2
<4:3>
SD ASPECT
<16:9>
*2
<NORMAL>
SCAN
<UNDER>
*2
<OFF>
NOISE WIPE
<ON>
*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not
reflected in the sub window.
*2 When "RGB-COMP." is selected in "YP
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
2) any other input line's HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line's SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When "VAR1", "VAR2" or "VAR3" is selected, the monitor switches to WB adjustment mode (
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue).
*6 By selecting "MODE1", you can convert IP through Frame Interpolation.
This unit has reduced the Frame Interpolation delay to 1 field or less, compared to our old models having caused 1
frame delay or more.
Factory preset setting value is "MODE1" recommended for normal use.
By selecting "MODE2", you can convert IP through Field Interpolation.
Since MODE2 interpolates only within each Field, it is suitable to confirm interlace condition.
Depending on still images, etc., flickers may occur on the screen. In such a case, "MODE1" is recommended.
Explanation
Used to select the gamma curve.
*1
When FILM is selected,
Used to select the type of FILM gamma mode.
<VARICAM> VARICAM use
<OTHER>
*5
Used to select the color temperature.
<USER0–63> Adjustable settings 0–63 (color temperature around 3000K–9300K)
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
*3
Used to select the width of the sharpness edge.
<HIGH>
*3
Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the screen.
*3
Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the screen.
Used to set the mode for IP change.
<MODE2> Field Interpolation
Used to switch between color and monochrome (MONO).
<OFF> Color
* When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.
If an Anamo lens has been used on the camera, and input through SDI
720/60P, 59.94P, the picture is resized to Anamo size magnification. (a
vertically compressed signal can be amplified vertically and corrected
when it is displayed.)
Used for setting the aspect ratio settings when using SD signal input.
<4:3>
4:3 display
Used to set under-scan and normal display.
<NORMAL>Normal display
<OFF> This makes a fluid and smooth contrast obtainable.
This is especially effective for continuously changing the contrast of
the source signal or CG signal when the S/N is very high.
<ON>
Noise reduction mode. Depending on the camera, this mode can
be especially effective for dark scenes. We recommend leaving
this setting "ON" under normal conditions.
P
/RGB" in the "INPUT SELECT" menu (
B
R
The underlined values are factory preset setting values.
mark is displayed in the top left of the screen.
When using other types than VARICAM
Color temperature around 9300K
Color temperature around 6500K
Color temperature around 5600K
*4
WB adjustment mode
*4
WB adjustment mode
*4
WB adjustment mode
Thin edge
<LOW>
<MODE1> Frame Interpolation
<ON>
<16:9>
<UNDER>Under-scan
2) Select 0–63 with [
Thick edge
Monochrome
16:9 display
page 22), this does not operate.
page 18).
,
], and push [ENTER].
17
Advertisement
Table of Contents
