1. Manuals
  2. Brands
  3. Polaris Manuals
  4. Offroad Vehicle
  5. Frontier Classic
  6. Owner's manual

Polaris Frontier Classic Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

2004
2004
Frontier Classic
Frontier Classic
Frontier Touring
Frontier Touring
Owner's Manual
Owner's Manual
for Vehicle Maintenance
for Vehicle Maintenance
and Safety
and Safety

Advertisement

Table of Contents
loading

Related Manuals for Polaris Frontier Classic

Summary of Contents for Polaris Frontier Classic

  • Page 1 2004 2004 Frontier Classic Frontier Classic Frontier Touring Frontier Touring Owner's Manual Owner's Manual for Vehicle Maintenance for Vehicle Maintenance and Safety and Safety...
  • Page 2 Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels. Failure to follow the safety precautions could result in serious injury or death. PROPOSITION 65 WARNING Snowmobile engines discharge fuel and exhaust, which contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm, onto the snow on...
  • Page 3 What’s the hottest thing on snow? Our new web site. And it’s designed just for YOU! Technical tips New product introductions Event schedules Parts and Service Manual information Exciting details about The Way Out Check it out... www.polarisindustries.com/owner...
  • Page 4 Copyright 2003 Polaris Sales Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication.
  • Page 5 Utility Task Vehiclest (UTVs) Personal Task Vehiclest (PTVs) All-Surface Loaders (ASLs) We believe Polaris sets a standard of excellence for all utility and recreational vehicles manufactured in the world today. Many years of experience have gone into the engineering, design, and development of your Polaris vehicle, making it the finest machine we’ve ever...

  • Page 6: Table Of Contents

    ......This section is a quick reference guide to solving problems. Polaris Products ......

  • Page 7: Introduction

    INTRODUCTION Important Notes for Owners and Drivers n After reading this manual, store it in the snowmobile for convenient reference. It should remain with the snowmobile when sold. n The illustrations and photos used in this manual may be general representations.

  • Page 8: Preservation Of The Environment

    Polaris snowmobiles are engineered to conform to these SAE standards. Our muffler systems are designed to reduce noise levels and must not be altered or removed. The sound of your snowmobile may not be welcome to non-snowmobilers, so you have a responsibility to operate your snowmobile with concern for others.

  • Page 9: Vehicle Identification Numbers

    Remove the spare key and store it in a safe place. Your key can be duplicated only by mating a Polaris key blank with one of your existing keys. If both keys are lost, the ignition switch must be replaced.

  • Page 10: Safety

    SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the manual. The safety alert symbol, on your vehicle or in this manual, alerts you to the potential for personal injury.

  • Page 11: Operator Safety

    We strongly recommend that the operator check major and vital safety components before every ride. All Polaris snowmobiles are designed and tested to provide safe operation when used as directed. Failure of critical machine components may result from operation with any modifications, especially those that increase speed or power.
  • Page 12 SAFETY Operator Safety Stay Away From Moving Parts WARNING Never hold the snowmobile up or stand behind it while warming up the track. A loose track or flying debris could cause serious personal injury or death. We recommend having your dealer perform track service and alignment procedures.

  • Page 13: Riding Position

    SAFETY Operator Safety Riding Position WARNING Improper riding position may seriously reduce your ability to control the machine and may result in serious injury or death. Always be properly seated and in position to control your vehicle. Operating a snowmobile requires skill and balance for proper control. Rider positions may vary from person to person as each becomes more skilled;...

  • Page 14: Cargo Overload

    SAFETY Operator Safety Cargo Overload Too much weight on the rear of the machine may reduce your ability to steer. Do not exceed carrier and rack weight limits, and do not allow a passenger to sit on the seat back or the cargo carrier. WARNING Control becomes more difficult with two people on board.

  • Page 15: Excessive Speed

    SAFETY Operator Safety Excessive Speed WARNING High speed driving, especially at night, could result in serious personal injury or death. Obey local traffic laws pertaining to snowmobile use and avoid using excessive speed. Observe all state and local laws governing snowmobile operation. They’ve been established for your protection.

  • Page 16: Driver Awareness

    SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you’re snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts.

  • Page 17: Driving On Slippery Surfaces

    SAFETY Operator Safety Ice and Snow Build-up WARNING Ice and snow build-up may interfere with the steering of your machine, resulting in serious injury or death. Keep the underhood area free of snow and ice. Before driving, manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering.

  • Page 18: Driving In Hilly Terrain

    SAFETY Operator Safety Driving in Hilly Terrain WARNING Climbing a hill or crossing the face of a slope may result in loss of balance and machine roll-over, causing serious injury or death. Use caution and good judgement when driving in hilly terrain. Operating in hilly terrain requires extreme caution to maintain balance and avoid roll-over.

  • Page 19: Driving Downhill

    SAFETY Operator Safety Driving Downhill When riding downhill, shift your weight to the rear of the machine and reduce your speed to a minimum. Apply just enough throttle to keep the clutch engaged, allowing the engine’s compression to help slow the machine and keep it from rolling freely downhill.

  • Page 20: Intake Silencer

    SAFETY Operator Safety Intake Silencer Damage to the engine may occur if the intake silencer or filter are removed. Clutches Do not attempt to service the clutches. All clutch service must be performed by your dealer. The clutch is a complex mechanism that rotates at high speeds.

  • Page 21: Powder Snow Operation

    SAFETY Operator Safety Powder Snow Operation WARNING Do not drive for prolonged periods on blacktop, gravel, or ice. Doing so could cause irreversible track damage and lead to serious personal injury. Since snow provides the only lubrication for the power slide suspension and cooling for the engine, adequate snow cover is a requirement for operation of your machine.

  • Page 22: Rider Capacities

    Rider Capacities Some Polaris snowmobiles are designed for a single rider only. Machines designed for two riders should never be operated with more than two people on board. When traveling with a passenger, it’s the driver’s responsibility to operate the machine safely.

  • Page 23: Driving Responsibly

    SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently, and even the most docile conditions may become dangerous if operators drive improperly. If you’re new to snowmobiling, acquaint yourself with the machine and with what it will and won’t do under various conditions. Even seasoned drivers should spend some time getting the feel for a machine before attempting ambitious maneuvers.
  • Page 24 SAFETY Operator Safety Windchill/Temperature Charts The following charts will help you determine when temperatures become dangerous for riding. WIND CHILL CHART (°F) Estimated Wind Speed Actual Thermometer Reading (°F) in MPH in MPH Equivalent Temperature (°F) Calm -112 -110 -124 -104 -118 -133...

  • Page 25: Safety Decals And Locations

    If any decal becomes illegible or comes off, contact your Polaris dealer to purchase a replacement. Replacement safety decals are provided by Polaris at no charge.

  • Page 26: Track Warning

    SAFETY Safety Decals And Locations Track Warning The track warning decal is located on the rear of the tunnel: Passenger Warning Some snowmobiles are designed for the operator only, while others are designed for the operator and one passenger. The passenger warning decal is located on the right side of the console next to the steering post.
  • Page 27 SAFETY Safety Decals and Locations Electronic Reverse Warning Polaris snowmobiles equipped with electronic reverse will have the electronic reverse warning decal. WARNING AVERTISSEMENT...

  • Page 28: Operation Warning

    SAFETY Safety Decals and Locations Operation Warning Operation warning decals are present on WARNING the console of all Polaris snowmobiles, in both French and English.
  • Page 29 SAFETY Safety Decals and Locations Operation Warning AVERTISSEMENT...

  • Page 30: Features And Controls

    FEATURES AND CONTROLS 1. Fuel Filler Cap 2. Ignition Switch 3. Brake Lever 4. Electronic Fuel Gauge 5. Speedometer 6. Headlight High Beam Light 7. Low Oil Pressure Light 8. Brake Light 9. Check Engine Light 10. Reverse Indicator Light 11.

  • Page 31: Features

    FEATURES AND CONTROLS Touring Model Shown 1. Hood 9. Snow Flap 2. Headlight 10. Suspension 3. Windshield 11. Track 4. Handlebar 12. Trailing Arm 5. Seat 13. Block Heater (under hood) 6. Passenger Seat (Touring) 14. Nosepan 7. Cargo Box (Touring) 15.

  • Page 32: Features

    Malfunction Indicator Lamp (MIL) The Frontier is equipped with a malfunction indicator lamp (CHECK ENGINE light) to assist your Polaris dealer in diagnosing problems. The MIL codes are for reference only. Full diagnostics must be performed by a Polaris dealer trained to service EFI systems.

  • Page 33: Features

    124 for the part numbers of Polaris products. CAUTION Mixing brands or using a non-recommended oil may cause serious engine damage. We recommend the use of Polaris Premium 4 Synthetic 0W-40 engine oil for your snowmobile. Never mix brands.

  • Page 34: Features

    FEATURES AND CONTROLS Block Heater To improve cold-weather starting, a block heater has been installed on the engine of your snowmobile. When connected to a 110V electrical outlet, the block heater warms the engine, making it easier to start in subzero temperatures.

  • Page 35: The Perfect Fit

    THE PERFECT FIT Front Suspension Adjustments Break in the suspension for approximately 150 miles (240 km) and re-grease all suspension parts before making any fine-tuning adjustments. Settings will vary from rider to rider, depending on rider weight, vehicle speed, riding style, and trail conditions. We recommend starting with factory settings and then customizing each adjustment individually to suit rider preference.

  • Page 36: Front Suspension Adjustments

    THE PERFECT FIT Front Suspension Adjustments WARNING Always verify ski alignment before making adjustments to the IFS. See page 107 to check alignment. If the skis are misaligned, see your dealer, as the camber adjustment may also be affected. For the best ride, the suspension should be adjusted to use the full travel of the shocks with occasional light bottoming.

  • Page 37: Front Springs

    Front Springs For models without externally adjustable or revalvable shocks, the front springs can be changed if spring preload alone isn’t sufficient and further adjustment is desired to control suspension stiffness. See your Polaris dealer for more information.

  • Page 38: Rear Suspension Adjustments

    Bogie wheel kits are available from your dealer. Polaris offers track kits for improved flotation in deep snow. See your dealer for assistance. NOTE: Keep the suspension pivot points lubricated. This will reduce moisture and rust build-up and ensure proper function of the suspension components.
  • Page 39 THE PERFECT FIT FAST M-10 Rear Suspension Adjustments The M-10 suspension has been designed to be very sensitive to rider weight. Changes in rider weight of 25 lbs. or more might require appropriate changes in settings. The following information has been compiled to assist you in tuning your M-10 suspension to its maximum potential and achieve the best possible ride.

  • Page 40: Fra Position

    THE PERFECT FIT FAST M-10 Rear Suspension Adjustments Static Sag and Ride Height Settings FRA Position The FRA setting is the primary rear suspension adjustment. It will have the MOST effect on the rear suspension performance. To adjust the FRA: 1.
  • Page 41 THE PERFECT FIT FAST M-10 Rear Suspension Adjustments Static Sag and Ride Height Settings Rear Spring Preload The top section of the crossover tube (the tube at the top of the rear shock) has a threaded collar on it. The rear spring has a lock tab that fits into the collar to allow easy spring preload adjustment.
  • Page 42 The available springs for M-10 suspension are listed below. Location Spring Rate Polaris PN Front Arm Standard 160 lbs./in. 7041671-216 Front Arm Soft 140 lbs./in.
  • Page 43 THE PERFECT FIT FAST M-10 Rear Suspension Adjustments Other Ride and Performance Settings Ski Pressure Your M-10 rear suspension ski pressure is set at the factory to deliver the optimum balance between ride and handling. If a rider prefers more ski pressure for improved steering performance, adjustments can be made to the front limiter strap and front arm mount.
  • Page 44 THE PERFECT FIT FAST M-10 Rear Suspension Adjustments Other Ride and Performance Settings Track Tension Track adjustment is critical for proper handling. Always maintain correct tension and alignment. Tension adjustments should be made only after the track is warmed up and limber. 1.
  • Page 45 THE PERFECT FIT FAST M-10 Rear Suspension Adjustments Initial M-10 Suspension Setup Chart NOTE: These positions are only preliminary. Experimentation should follow initial setup to obtain optimum results. Refer to the suspension troubleshooting decal for additional setup tips. INITIAL SETUP REFERENCE CHART This chart is a guideline to be used for initial suspension setups.
  • Page 46 THE PERFECT FIT FAST M-10 ACE Suspension Adjustments The FAST M-10 ACE (Adjustable Control Electronics) is a new feature available for some FAST M-10 rear suspensions. It enables a rider to easily adjust the suspension for weight and riding style. The M-10 ACE is an electronically controlled module that replaces the standard M-10 FRA.

  • Page 47: Important Notes

    THE PERFECT FIT FAST M-10 ACE Suspension Adjustments M-10 ACE Settings IMPORTANT NOTES: The time to move one position can take up to 12 seconds depending on the rear shock loads. Due to alternator limitations, the ACE module will operate only at engine speeds above 3500 RPM.
  • Page 48 THE PERFECT FIT FAST M-10 ACE Suspension Adjustments Initial M-10 ACE Setup Chart NOTE: These positions are only preliminary. Experimentation should follow initial setup to obtain optimum results. Refer to the suspension troubleshooting decal for additional setup tips. INITIAL SETUP REFERENCE CHART This chart is a guideline to be used for initial suspension setup.
  • Page 49 THE PERFECT FIT Edge Touring Suspension (ETS) Adjustments Torsion Springs Two torsion springs are used on the rear arm of the ETS. Preload adjustments can be made by turning the rectangular adjusters with a spark plug wrench. The firm torsion spring should be used if frequent bottoming is encountered during two up riding on rough trails.
  • Page 50 THE PERFECT FIT Edge Touring Suspension (ETS) Adjustments Initial Setup and Calibration The following information has been compiled to assist you in tuning your ETS to its maximum potential. The Ride Control Adjuster (RCA) 1. Refer to the initial setup reference chart (located under the hood of your snowmobile and on page 47) to determine the desired RCA position.

  • Page 51: Handlebar Adjustments

    Follow the adjustment procedures exactly, or see your Polaris dealer for service. Follow these steps to adjust the handlebars for a personal fit. 1. Remove the handlebar cover to expose the handlebar and the four adjuster block bolts (A).

  • Page 52: Traction Products

    Accessories Polaris offers a wide range of accessories for your snowmobile. From map light to saddlebags, Polaris has the accessories that will help make each ride more enjoyable. See your dealer for a list of accessories. NOTE: The accessory tether switch is available for all models. Order PN 2870668.
  • Page 53 THE PERFECT FIT Accessories Traction Products Track studding will enhance braking control on hard-packed snow or ice, but extreme caution is still required on such surfaces. Steering ability may be reduced on hard-packed snow or ice. A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmobile and to prevent ski wear caused by contact with roads and other bare terrain.

  • Page 54: Wear Strips

    THE PERFECT FIT Accessories Wear Strips To avoid excessive tunnel wear, tunnel wear strips must be installed whenever track studding is used. Several wear strips are available. See your dealer for more information. Some models are manufactured with tunnel wear strips or wear strip coolers installed.

  • Page 55: Pre-Ride Inspections

    PRE-RIDE INSPECTION Before starting the engine, always check all of the items outlined on the following pages. WARNING Worn, damaged, or malfunctioning components may cause serious injury or death. Before starting the engine, check all Pre-Ride Inspection components to be sure of proper operation. Read and Understand Your Owner’s Manual Read the Owner’s Manual completely and refer to it often.

  • Page 56: Hydraulic Brakes

    Also check for the presence of air in the fluid system. Refer to page 92 for more information, or see your dealer for service. Replace brake fluid at least every two years with Polaris DOT 3 high temperature brake fluid. All DOT 3 brake fluid is not alike. We recommend that you use only Polaris brake fluid.

  • Page 57: Park Brake Lever Lock

    PRE-RIDE INSPECTION Park Brake Lever Lock Your snowmobile has a park brake lever lock located over the brake lever. Use the brake lever lock when you want the machine to remain stationary; for example, when parked on an incline for a period of five minutes or less.
  • Page 58 PRE-RIDE INSPECTION Steering System Manually turn the skis completely to the right and to the left. If any difficulty is encountered, check for ice and snow build-up that may be obstructing the steering linkage. Make sure all greasable components are properly lubricated. Track Condition Driving at high speeds for extended periods of time in marginal lubrication could severely damage track rods, break track edges, and...
  • Page 59 PRE-RIDE INSPECTION The following items must be checked before each use of the vehicle. Check these items after starting the engine (see page 58), but before putting the machine into motion. Transmission Make sure the reverse is not engaged before squeezing the throttle. Engine Stop Switch Check the auxiliary shut-off switch for proper operation.

  • Page 60: Operation

    OPERATION Starting the Engine WARNING Before starting the engine, always refer to all safety warnings pertaining to snowmobile operation. Never start your snowmobile without checking all components to be sure of proper operation. See Pre-Ride Inspection section beginning on page 53. Do not depress the throttle until the engine starts.
  • Page 61 OPERATION Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. During the first three hours of operation, operate the snowmobile as outlined in this Engine Break-In section. CAUTION Failure to follow the procedures outlined in the Engine Break-In section of the owner’s manual could result in serious damage to...
  • Page 62 We recommend the use of Polaris Premium 4 Synthetic 0W-40 engine oil for your snowmobile. Never mix brands. We highly recommend the use of only Polaris products for your snowmobile. We’re continuously testing lubricants and provide the highest performance products available for your snowmobile’s engine.
  • Page 63 OPERATION CAUTION Inadequate cooling and lubrication will lead to overheating of the slide rail and track, resulting in premature wear and failure. Reduce speeds and frequently drive into fresh snow to allow adequate cooling and polishing of the slide rail and track surfaces. Avoid operating on ice, hard-packed surfaces or roads.
  • Page 64 OPERATION Fuel WARNING Gasoline is highly flammable and explosive under certain conditions. Always exercise extreme caution whenever handling gasoline. Always refuel with the engine stopped, and outdoors or in a well ventilated area. Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored.

  • Page 65: Fuel System Deicers

    OPERATION Fuel The fuel used in your Polaris engine is as important to engine life and performance as the lubricant. Your Polaris engine is designed to run on a minimum of 87 octane non-oxygenated or 89 octane oxygenated pump gasoline. There’s a great deal of variability in the quality of the 87 octane gasoline available across the country, so we encourage the use of premium fuel when possible.
  • Page 66 WILL result in deteriorated engine performance and could result in SEVERE engine damage. NEVER attempt to adjust the TPS. Always have your Polaris dealer perform any service on the TPS. All throttle bodies have been preset at the factory for adequate fuel supply at all altitudes.
  • Page 67 OPERATION Engine Stop Switch Push down on the engine stop switch (A) to stop the engine in an emergency. This will ground out the ignition and bring the engine to a quick stop. To restart the engine, the switch must be pulled up to the ON position.

  • Page 68: Throttle Lever

    When these switches are disconnected, the ignition key switch must be used to shut off the engine. DO NOT continue to operate the machine with the throttle safety switch disconnected. See your authorized Polaris dealer for service as soon as possible.

  • Page 69: Emergency Stopping

    OPERATION Emergency Stopping The following chart lists methods for stopping the snowmobile in the event of an emergency. Refer to page 65 for more information about the engine stop switch and throttle safety switch. SYSTEM WHAT IT DOES THROTTLE CONDITION Ignition Switch Interrupts ignition circuit Brake...

  • Page 70: Reverse Operation

    OPERATION Reverse Operation WARNING Improper reverse operation, even at low speeds, may cause loss of control, resulting in serious injury or death. Always look behind the vehicle before and while backing. Always avoid sharp turns. Shift to or from reverse only when stopped. Always apply throttle slowly.

  • Page 71: Daily Storage

    The track should be suspended approximately 4″ (10 cm) off the ground. Remove the key and cover the machine. NOTE: Polaris has accessory covers and track stands available to fit all mod- els. See your dealer for more information.
  • Page 72 OPERATION Towing For your safety, do not attempt to use the tow hitch until you’ve read the following warnings and understand the proper hitch functions. WARNING Objects towed with a rope have no braking power and can easily collide with the rear of the snowmobile or other objects, resulting in serious injury or death.

  • Page 73: Maintenance

    Personal safety is critical when attempting to service or adjust your snowmobile. If you’re not familiar with safe service or adjustment procedures and the use of tools, or if you don’t feel comfortable performing these tasks yourself, contact an authorized Polaris dealer for service. EFI System There are no maintenance adjustments required for the EFI system.

  • Page 74: Maintenance Chart

    The following chart is a guide based on average riding conditions. You may need to increase frequency based on riding conditions. When inspection reveals the need for replacement parts, always use genuine Polaris parts, available from your Polaris dealer. Item Weekly or...
  • Page 75 MAINTENANCE Maintenance Chart Item Weekly or 1000 before miles miles miles Page long trip (240 km) (800 km) (1600 km) Check Hi-fax thickness, have dealer replace when worn Tighten rear idler wheel bolts Tighten idler adjust bolt jam nuts Check spark plug condition, re- place annually Inspect coolant filter, replace if necessary...

  • Page 76: Maintenance Log

    This will provide you and future owners with an accurate log of maintenance and services performed on the snowmobile. 150 Mile (240 km) Initial Maintenance Inspection Authorized Polaris Servicing Dealer Servicing Technician Date Mileage 500 Mile (800 km) Maintenance Inspection...
  • Page 77 MAINTENANCE Maintenance Log Additional Services Performed Authorized Polaris Servicing Dealer Servicing Technician Date Mileage Type of Service Additional Services Performed Authorized Polaris Servicing Dealer Servicing Technician Date Mileage Type of Service...
  • Page 78 Grease the center steering arms. Grease the steering post lower pivot. Grease the rear suspension pivot shafts (raise the rear of unit). A grease gun kit, complete with grease and adaptors, is available to lubricate all fittings on Polaris snowmobiles. See page 124.
  • Page 79 MAINTENANCE Lubrication The suspension pivot shafts should be lubricated with Polaris Premium All Season Grease at 500 miles (800 km) initially, every 1000 miles (1600 km) after that, and before off-season storage each year. Lack of lubrication will adversely affect your ride and the life of the suspension.

  • Page 80: Jackshaft Bearing

    MAINTENANCE Lubrication Jackshaft Bearing Loosen the driven clutch retaining bolt and pull the clutch outward to expose the bearing and grease fitting. Inject grease into the grease fitting in the flangette until grease purges from inside or outside the bearing seal (may take only two pumps).

  • Page 81: Chaincase Oil

    Place the machine on a level surface. Remove the dipstick (A) and read the oil level. The oil level should be between the SAFE marks on the dipstick. Add Polaris chaincase oil through the dipstick opening if needed. Do not overfill. See page 124 for the part numbers of Polaris products.
  • Page 82 General Maintenance Spark Plugs CAUTION Using non-recommended spark plugs can result in serious engine damage. Always use Polaris-recommended spark plugs. Use Champion RC7YC spark plugs. Proper electrode gap is .035” (.9 mm) Spark plug torque is 18-22 ft. lbs. (24-30 Nm).
  • Page 83 MAINTENANCE General Maintenance Spark Plugs Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine has been warmed up and the vehicle has been driven at higher speeds. Immediately check the spark plug for correct color. WARNING A hot exhaust system and engine can cause serious burns.

  • Page 84: Intake Filter

    MAINTENANCE General Maintenance Intake Filter The intake foam filters limit snow ingestion into the intake system. When operating in loose powder snow, check the filters periodically to remove any accumulation of snow. 1. Airbox foam filter 2. Air intake box 3.

  • Page 85: Oil And Filter Change

    6. Install the new filter and turn by hand until the filter gasket contacts the sealing surface, then turn an additional half turn. 7. Add 2 quarts (1.9 ltr) of Polaris Premium 4 synthetic oil through the dipstick hole. Reinstall the dipstick.

  • Page 86: Exhaust System

    MAINTENANCE General Maintenance Exhaust System Check the exhaust system for wear or damage at approximately 1000 miles (1600 km). To inspect, allow the engine and exhaust system to cool completely. Open the hood and inspect the muffler and pipes for cracks or damage.
  • Page 87 Use Premium 60/40 anti-freeze coolant, which is already premixed and ready to use. Do not dilute with water. See page 124 for the part numbers of Polaris products. Never exceed a 60% antifreeze/40% water mixture. Contact you dealer if greater protection is required.

  • Page 88: Coolant Level

    50/50 or 60/40 mixture of antifreeze and distilled water should be added. This service must be done when the engine is cold. Ask your Polaris dealer to check the coolant when he performs the fall tune-up on your snowmobile.

  • Page 89: Bleeding The Cooling System

    MAINTENANCE General Maintenance Bleeding the Cooling System WARNING Steam and hot liquids will cause serious burns to your skin. Never bleed the cooling system or remove the pressure cap when the engine is warm or hot. If the pressure cap needs replacement, contact your dealer for the correct part.

  • Page 90: Drive Chain Tension

    MAINTENANCE General Maintenance Drive Chain Tension To obtain correct chain tension: 1. Rotate the driven clutch counterclockwise to move all chain slack to the tensioner side. Lock the brake lever lock, or have an assistant hold the brake lever firmly. 2.

  • Page 91: Hydraulic Brake Inspection

    MAINTENANCE General Maintenance Hydraulic Brake Inspection Frequently inspect the brake lever reserve. Firmly depress the brake lever and measure the clearance between the lever and handlebar grip. This distance, called brake lever reserve (A), should be no less than 1/2″ (1.3 cm). Brake pads must be replaced when the brake pad material becomes thinner than the backing plate (approximately 1/16″).

  • Page 92: Brake Components

    5. Brake Pad Material (Replace when thickness is less than 1/16″). Excessive Brake Lever Travel Hydraulic brakes are self-adjusting, but if excessive brake pad clearance develops, as described on page 89, the machine should be returned to an authorized Polaris dealer for inspection and adjustment.

  • Page 93: Brake Fluid

    All DOT 3 brake fluid is not the same. We recommend the use of only Polaris DOT 3 high temperature brake fluid. See page 124 for the part numbers of Polaris products. The brake fluid level can be seen through a plastic sight glass in the brake reservoir.

  • Page 94: Bleeding The Hydraulic Brake System

    MAINTENANCE General Maintenance Bleeding the Hydraulic Brake System Air in the hydraulic brake system will cause spongy brake lever action. Bleed the system before operating the snowmobile. WARNING Operating the vehicle with a spongy brake lever can result in loss of brakes, which could cause an accident and lead to serious injury or death.

  • Page 95: Headlight Adjustment

    MAINTENANCE General Maintenance Headlight Adjustment The headlight may be adjusted for 25’ (7.6 m) vertical aim using the following procedure: 1. Place the snowmobile on a level Lamp Center surface with the headlight Height approximately 25 feet (7.6m) from a wall. 2″...
  • Page 96 MAINTENANCE General Maintenance NOTE: Do not touch a halogen bulb with bare fingers. Oil from skin leaves a residue, causing a hot spot that will shorten the life of the lamp. Headlights Removing Halogen Bulbs - High/Low Beam 1. Pinch the ends of the spring (1) together and lift until it releases from the spring retainer.

  • Page 97: Clutch System

    CAUTION The bushings in the weights and rollers of Polaris clutches are made of a material that may be damaged if lubricated. Do not lubricate clutch bushings. Periodically inspect the clutch sheaves for damage, wear, or belt residue.
  • Page 98 The drive belt is a very important part of the drive system. Belt width and length must match the center distance of the clutches and sheave width of the drive clutch. For this reason, Polaris recommends that only O.E.M. belts be used. Other belts may match the dimensions, but can drastically change the shift pattern, resulting in poor performance.
  • Page 99 MAINTENANCE Frontier Classic Clutching Chart Altitude Shift Drive Driven Driven Chaincase Weight Clutch Clutch Helix Gearing Meters (Feet) Spring Spring 0-900 10-62 Yellow Silver R-11 19:39 72P (0-3000) HYVO 900-1800 10-62 Yellow Silver R-11 19:39 72P (3000-6000) HYVO 1800-2700 10-58...

  • Page 100: Drive Belt Removal

    MAINTENANCE General Maintenance Periodically check the condition and tension of the drive belt, and always carry a spare belt. For improved drive-away during extremely cold temperatures, remove the belt and warm it to room temperature. Reinstall it before starting the snowmobile. Drive Belt Removal 1.

  • Page 101: Drive Belt Installation

    MAINTENANCE General Maintenance Drive Belt Installation 1. Drop the drive belt over the drive clutch and pull back the slack (A). NOTE: To ensure satisfactory belt life, install belts so they operate in the same direction of rotation by positioning the identification numbers so that you can read them.

  • Page 102: Drive Belt Adjustment

    MAINTENANCE General Maintenance Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position. Place a straight edge on the belt (A) and apply downward pressure while measuring at point B. This measurement should be 1 1/4”. Drive Belt Adjustment Belt deflection can be adjusted without removing the clutch from the jackshaft.

  • Page 103: Reverse Kit Maintenance

    MAINTENANCE General Maintenance Reverse Kit Maintenance Always maintain track tension as specified on page 42 when a snowmobile is equipped with reverse. WARNING Improper track tension can cause serious damage to the snowmobile, which can result in loss of vehicle control and serious injury or death.

  • Page 104: Tool Kit

    7. Box End Wrench NOTE: Always keep the tool kit with the snowmobile. If necessary, a replacement tool kit may be purchased from your Polaris dealer. Tool Pouch The Frontier Classic has a seat compartment bag for tool storage. Touring models have a tool pouch clip (A), which is located under the hood.

  • Page 105: Emergency Supplies

    SFirst Aid Kit Fall Tune-Up For maximum performance, arrange for a fall service tune-up with your Polaris dealer. His experienced and trained service technicians will keep your machine in peak operating condition. Maintenance Tools The tools and maintenance items mentioned in this book, as well as...

  • Page 106: Track Alignment

    MAINTENANCE Track Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment will cause excessive wear to the track and slide rail. 1. Safely support the rear of the machine with the track off the ground.

  • Page 107: Track Inspection

    MAINTENANCE Track Maintenance Track Inspection WARNING Broken track rods can cause a rotating track to come off the machine, which could result in serious injury or death. Never operate with a damaged track. Never rotate a damaged track under power. Using a hoist, safely lift and support the rear of the snowmobile off the ground.

  • Page 108: Steering Inspection And Adjustment

    MAINTENANCE Steering System Steering Inspection and Adjustment Each week, or before a long ride, check fasteners and tighten if needed. Specific fasteners that should be checked are marked with a...

  • Page 109: Ski Alignment

    Do not attempt to change the ski alignment or camber adjustment. See your Polaris dealer. With the handlebars in a straight ahead position, and with vehicle weight compressing the suspension, measure from the straight edge of the skis at the center of the ski mounting bolt.

  • Page 110: Ski Skags

    MAINTENANCE Steering System Ski Skags WARNING Worn skis and/or skags will adversely affect handling. Loss of vehicle control may result, causing serious injury or death. See your dealer’s studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle control while turning on hard-packed snow or ice.

  • Page 111: Suspension Maintenance

    MAINTENANCE Suspension Maintenance Hi-Fax Wear Replace Hi-fax when a thickness of 7/16″ (1.1 cm) is reached. Check 7/16″ (1.1 cm) Hi-fax wear by measuring the thickness at several points along the rail (A). Take the machine to your dealer for Hi-fax replacement.

  • Page 112: Controls And Linkage

    MAINTENANCE Suspension Maintenance Loose nuts and bolts can reduce your snowmobile’s reliability and cause needless repairs and down time. Before beginning any snowmobile trip, a visual inspection will uncover potential problems. Check the following items on a weekly basis or before any long trip: n Check rear idler wheel bolts for tightness.

  • Page 113: Clutch And Drive System

    MAINTENANCE Extended Storage Bearings Grease the jackshaft and drive shaft clutch side bearings with Polaris Premium All-Season Grease or a similar high quality grease to prevent corrosion. See page 124 for part numbers. Clutch and Drive System Remove the drive belt and store in a cool dry location. Lubricate the sheave faces of the drive and driven clutches with a light coat of oil or Polaris Cable Lubricant.

  • Page 114: Engine Protection

    MAINTENANCE Extended Storage Engine Protection Proper preparation of the engine and fuel system is vital to the prevention of rust and corrosion on precision engine parts during storage. Whenever the machine is stored for a period of more than 60 days, the engine must be fogged with fogging oil.

  • Page 115: Track And Suspension

    MAINTENANCE Extended Storage Track and Suspension Moderate track tension should be maintained during summer storage. The machine should be supported off the ground to allow the track to hang freely. See illustration. Battery WARNING Battery electrolyte is poisonous. It contains acid! Serious burns can result from contact with the skin, eyes, or clothing.

  • Page 116: Battery Connections

    MAINTENANCE Battery Battery Connections Keep battery terminals and connections free of corrosion. When cleaning is necessary, remove the corrosion with a stiff wire brush. Wash terminals and connections with a solution of one tablespoon baking soda and one cup water. Rinse well with tap water and dry with clean shop towels.

  • Page 117: Battery Installation

    MAINTENANCE Battery When your snowmobile is placed in storage for one month or more: Remove the battery. Charge it to the proper level. Store it in a cool dry place. Check and/or charge monthly. Before using the battery, take it to your dealer for testing and recharging.

  • Page 118: Specifications

    SPECIFICATIONS Frontier Classic Body Style Edge Riders Coolant 5.9 qts./5.6 l Chaincase Oil 12 oz./.35 l Engine Oil 2.12 qts./2 l Dry Weight (est.) 562 lbs./255 kg Fuel Tank 11.8 gal./44.7 l Height 49 in./124.5 cm Length 113 in./287 cm Ski Center Distance 42.5 in./108 cm...
  • Page 119 SPECIFICATIONS Frontier Touring Body Style Edge Riders Coolant 6 qts./5.7 l Chaincase Oil 13 oz./.38 l Engine Oil 2 qts./1.9 l Dry Weight (est.) 645 lbs./292.6 kg Fuel Tank 12.25 gal./46.4 l Height 49.5 in./125.7 cm Length 125 in./317.5 cm Ski Center Distance 42.5 in./108 cm Width...

  • Page 120: Troubleshooting

    TROUBLESHOOTING M10 Suspension Troubleshooting Problem Solution (perform only one change at a time) Rear suspension - Increase FRA position (see setup decal under hood for initial bottoms too easily position - Increase X-over tube length (see setup decal under hood) - Increase rear track shock coil spring preload - Increase front track shock coil spring preload - Change to optional stiff rear track shock compression spring...
  • Page 121 TROUBLESHOOTING ETS Suspension Troubleshooting Problem Solution (perform only one change at a time) Rear suspension - Adjust RCA forward (see setup decal under hood). bottoms too easily - Adjust coil over spring on front track shock to increase preload - 1” maximum preload. - Adjust torsion spring blocks to highest position.

  • Page 122: Belt Troubleshooting

    TROUBLESHOOTING Belt Troubleshooting Belt Wear/Burn Belt Wear/Burn Diagnosis Causes Solutions Driving at low RPM Drive at higher RPMs. Gear the machine down. Check belt deflection. Insufficient warm-up Warm the engine at least five minutes. Take the drive belt off the machine in extremely cold weather and warm it up. Break machine loose from the snow.
  • Page 123 TROUBLESHOOTING Engine Troubleshooting CAUTION: All engine service and repair should be performed by a qualified Polaris dealer with training in EFI engines. Problem Probable Cause Solution Erratic engine Drive clutch bind- -Disassemble drive clutch to inspect shift operating RPM weights for wear and free operation.
  • Page 124 TROUBLESHOOTING Engine Troubleshooting Problem Probable Cause Solution Noise in drive Broken drive clutch -SEE YOUR DEALER. system components Bearing failure/ -SEE YOUR DEALER. chaincase, jack- shaft, or front drive shaft Drive belt surface -Inspect and replace if necessary. flat spots Drive chain loose -Inspect and adjust or replace.
  • Page 125 TROUBLESHOOTING Engine Troubleshooting Problem Probable Cause Solution Engine turns Faulty ignition -Check for spark; if no spark SEE DEALER. but fails to start No fuel to engine -Check tank level and fill with correct fuel. -Ice in fuel line, filter, or pump. Air in fuel line -SEE DEALER for fuel line bleeding.

  • Page 126: Polaris Products

    POLARIS PRODUCTS Part No. Description Engine Lubricants 2870791 Fogging Oil (12 oz. Aerosol) 2871281 Premium 4 Synthetic 0W-40 Engine Oil (4-Cycle)(qt.) Chaincase Lubricants 2873105 Synthetic Chaincase Lubricant (qt.) 2872951 Synthetic Chaincase Lubricant (12 oz.) Grease / Specialized Lubricants 2871312 Grease Gun Kit, Premium All Season (3 oz.) 2871322 Premium All Season Grease (3 oz.

  • Page 127: Warranty

    2. Polaris warranty will provide all dealerships with a monthly updated list of all stolen units to further monitor thefts. 3. Polaris warranty will aid in notifying the proper owner when a unit is recovered.

  • Page 128: Limited Warranty

    WARRANTY Limited Warranty Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, provides a ONE YEAR LIM- ITED WARRANTY on all components of the Polaris snowmobile against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective parts that are covered by this warranty.

  • Page 129: Engine Oil

    How to Obtain Warranty Service If your snowmobile requires warranty service, you must take it to a Polaris dealer autho- rized to repair Polaris snowmobiles. When requesting warranty service you must present your copy of the Warranty Registration form to the dealer. (The cost of transportation to and from the dealer is YOUR responsibility).
  • Page 130 In order to qualify for warranty, the product must have been properly set up and tested by a Polaris Dealer (if applicable). Failure of any dealer to perform the required vehicle Pre- Delivery Inspection, perform all applicable service bulletins and have the consumer sign the PDI form prior to delivery may void the warranty.
  • Page 131 S Failures caused due to improper adjustments. S Failure due to unauthorized service. S Failures due to lack of service as required in the owner’s manual or Polaris updates. This includes off-season storage as listed in the owner’s manual. S Failure due to use of unauthorized parts or modifications.
  • Page 132 If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied.

  • Page 133: Index

    INDEX Accessories ....50-52 Disabled Operators ... . . Air Box ..... Drive Belt .
  • Page 134 ..Passenger ....POLARIS PRODUCTS ..Handlebar Adjustments .
  • Page 135 INDEX Suspension Performance Tips ......Suspension Setup Chart, ETS ..Track .
  • Page 136 For your nearest Polaris dealer, call 1-800-POLARIS or visit www.polarisindustries.com Polaris Sales Inc., 2100 Hwy. 55, Medina, MN 55340 Phone (763) 417-8650 Fax (763) 542-0599 Part No. 9918289 Rev 02 Printed in USA...

This manual is also suitable for:

Frontier touring

Table of Contents