Clock; Timer - Philips FW545 Manual

CLOCK

Viewing the Clock
You can view the clock (if it is set) while
the system is in standby mode or any
source mode. It will be displayed for about
7 seconds.
• Press CLOCK/TIMER briefly (on the
system only) .
™ "10:38" (the current time) will be
™ "--:--" will be displayed if the
22
Untitled-13
Downloaded From Disc-Player.com Philips Manuals
MINI HIFI SYSTEM
PROGRAM SHUFFLE STEREO
REPEAT

TIMER

REC BACK
LW FRONT HSD
NEWS T.A. AM MW FM
60Hz 250Hz 500Hz 1KHz 2KHz 4KHz 8KHz
STANDBY
ON
CLOCK/
TIMER CD1 • 2 • 3 BAND TAPE 1 • 2 CDR
CD TUNER TAPE AUX
PROG
SIDE A•B PRESET
SEARCH • TUNING STOP•CLEAR PLAY PAUSE PREV NEXT
SOUND NAVIGATION
INCREDIBLE DYNAMIC BASS
SURROUND BOOST
DIGITAL
SOUND CONTROL
Setting the Clock
The clock is set in 24-hour mode, e.g.
"00:00" or "23:59". Before setting
the clock, you must be in the View Clock
mode.
1 Press CLOCK/TIMER to select clock
mode.
™ "00:00" or the current time starts
displayed. flashing.
2 Set the hour with à or á.
3 Set the minute with í or ë.
clock is not set.
4 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
22
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
RDS
– When a power interruption occurs, the
NEWS/TA
clock setting is erased.
VOLUME
– To set the time with RDS clock, see
A. REV
"Receiving RDS Radio Station" under
TUNER section.
MIC
LEVEL
MIC
Setting the Timer
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will start to
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than 2 seconds to select timer mode.
™ "00:00" or the last set timer starts
flashing. The
TIMER
™ The last selected source is lit while
other available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press à or á to set the hour for the
timer to start.
4 Press í or ë to set the minute for
the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The flag remains on the display.
TIMER
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the last
selected disc. If the CD trays are empty,
the TUNER will be selected instead.
– If the source selected is TAPE, and if the
preset time is reached during high
speed dubbing, the TUNER will be
selected instead.
flag flashes.
3139 116 18533
6/15/00, 1:16 PM
TIMER