Minolta dynax 7 Repair Manual page 64

64 (2181)
Adjustment (Common)
0x**00**** At the time of a successful adjustment
0x**f0****
Arguments are not good. (Not camera errors）
0x**f1**** USB port initialization is not good.
0x**f2**** Diaphragm control is not good.
0x**f3**** Reset of ANIT-SHAKE is not good.
0x**f4**** Reset of FOCUS is not good.
0x**f5****
Reset of SHUTTER control is not good.
0x**f6****
Camera-charging time has been exceeded.
0x**f7**** Readout of ZOOM data is not good.
0x**f8****
Readout of Temprature data is not good.
0x**f9**** Zoom drive is not good.
0x**fa**** Adjustment sequence is not good.
0x**fb**** Setting of Camera mode is not good.
0x**fc**** Initialization
0x**fd****
Adjustment data is not good. (Out of the standard)
0x**fe**** Access of Flash ROM is not good.
0x**ff**** Setting of various kinds is not good.
Adjustment (Image taking system)
0x70****** NG for Black level Adjustment
0x**01**** Value is Greater than standard.
0x71****** NG for Sesitivity Adjustment
0x**01**** Retry over
0x**02**** Value is too small
0x**03**** Value is too large
0x73******
NG for Missing Pixel Comp. Adjustment (Blk)
0x**00**** There are many black dead pixels.
0x**01**** Both adjoining pixels are dead pixels.
0x74******
NG for Missing Pixel Comp. Adjustment (W ht)
0x**00**** There are many white defective pixels.
0x**01**** Both adjoining pixels are defective pixels.
0x75****** NG for Missing Pixel Comp Adj. (Long Exp.)
0x**00**** There are many white defective pixels.
0x**01**** Both adjoining pixels are defective pixels.
0x77****** NG for WB Adjustment
0x**00****
Setting of Camera or USB communication err.
0x**01**** Too low exposure
0x**02**** Too high exposure
0x**03**** Too low R-Gain on Light source-A
0x**04**** Too high R-Gain on Light source-A
0x**05**** Too low B-Gain on Light source-A
0x**06**** Too high B-Gain on Light source-A
0x**07**** Too low R-Gain on Light source-C
0x**08**** Too high R-Gain on Light source-C
0x**09**** Too low B-Gain on Light source-C
0x**0a**** Too high B-Gain on Light source-C
0x78****** NG for AORI Adjustment
0x**00****
Setting of Camera or USB communication err.
Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system)
0x90******
NG for CCD CENTER Adjustment
0x**01****
Setting of Camera
0x**02****
Communication for SHAKE compensation
0x**03****
Communication for SHAKE compensation
0x**04****
Communication for Image taking system
0x**05****
Setting of Driving-direction
0x**06****
Shading-data has not been detected.
0x**07****
Shading-data has not been detected.
0x**08****
Adjustment value (Pitch)
0x**09****
Adjustment value (Yaw)
0x**0a****
Writing of Adjustment value
0x91******
NG for ACT DRV FREQ Adjustment
0x**00****
USB communication
0x**01****
Setting of Camera
0x**02****
Communication for SHAKE compensation
0x**03****
Adjustment value
0x**04****
Writing of Adjustment value
0x**05****
Speed error of Pitch or Yaw
0x**08****
0x92******
NG for SERVO Adjustment
0x**01****
Setting of Camera
0x**02****
Communication for SHAKE compensation
0x**03****
Received data of CPU
0x**04****
Electric current mode
0x**10****
0x**20****
Check Sum error
0x**21****
Frequency error
0x**22****
Final distributed data error
0x**23****
Final distributed data error
0x93******
NG for GYRO Adjustment
0x**01****
Setting of Camera
0x**02****
Communication for SHAKE compensation
0x**03****
Voltage of IC Vref
0x**04****
Value of GYRO offset
0x**05****
Value of GYRO offset
0x**06****
Initial value of DAC
0x**07****
Initial value of DAC
0x**08****
Vibration was detected during adj. (Pitch)
0x**09****
Vibration was detected during adj. (Yaw)
0x**0a****
Temperature of Lens
0x**0b****
Writing of Adjustment value
0x94******
NG for SHAKE GAIN Adjustment
0x**01****
Detect white line
0x**02****
P to P error
0x**0a****
0x**0ｂ****
White line is too wide. (Pitch)
0x**0c****
White line is too wide. (Yaw)
0x**0d****
No detection of minimum gain.
0x**10****
0x**11****
Rest of SHAKE Comp. Greater than standard. (pitch)
0x**12****
Rest of SHAKE Comp. Greater than standard. (Yaw)
Other Adjustment
0xe2******
NG for Vsub Adjustment
0x**01****
Adjustment initialization error
0x**02****
Vsub data 1 is out of range.
0x**03****
Vsub data 2 is out of range.