Minolta dynax 7 Repair Manual
  1. Manuals
  2. Brands
  3. Minolta Manuals
  4. Film Camera
  5. DYNAX 7
  6. Repair manual

Minolta dynax 7 Repair Manual

Hide thumbs Also See for dynax 7:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual , User Manual
This repair guide section contains the disassembly and adjustment procedures.
For the assembly procedure, follow the reverse procedure.
SYMBOLS
■:Cautions and keypoints
: Grease
: Adhesive
: Tool
CONTENTS
■Precautions --------------------------------------------- 2
■Discharge ------------------------------------------------ 2
■To inhibit flash charge ------------------------------- 3
■ Wires arrangement ----------------------------------- 5
SHUTTER ASSY ----------------------------------- 7
BATTERY HOLDER ----------------------------- 10
MAIN BOARD ASSY ----------------------------- 11
DC JACK HOLDER ------------------------------ 26
required setting items ---------------------------- 32
■Using HIT System ----------------------------------- 33
with 2181 ROM Pack ---------------------------- 34
■Viewfinder Back Adjustment ---------------------- 35
■Manual Set SS Adjustment ------------------------ 37
■SPC Position Adjustment --------------------------- 38
■PI-PR Adjustment ------------------------------------ 40
REPAIR GUIDE
Page
CONTENTS
①AF Area Adjustment --------------------------------- 43
② Pitch Yaw Adjustment ------------------------------ 44
③ EZ Check ----------------------------------------------- 45
④EZ Adjustment ---------------------------------------- 46
■Assist MODE ------------------------------------------ 47
■LCD Displays Check --------------------------------- 47
(in the adjustment mode). ----------------------- 49
adjustment of CCD position --------------------- 52
camera shaking (SERVO) ----------------------- 55
camera shaking (GYRO) ------------------------- 55
■Adjustment of the AE (AE) ------------------------- 56
■Sensitivity adjustment (GAIN) -------------------- 57
(DEFECT PIXEL) --------------------------------- 58
compensation (SHAKE GAIN) ----------------- 60
■Light Source-A Maintenance ----------------------- 62
■Measuring instrument ------------------------------ 65
■Subsidiary Materials --------------------------------- 66
(2181) 1
Page

Advertisement

Table of Contents
loading

Related Manuals for Minolta dynax 7

Summary of Contents for Minolta dynax 7

  • Page 1: Table Of Contents

    (2181) 1 REPAIR GUIDE This repair guide section contains the disassembly and adjustment procedures. For the assembly procedure, follow the reverse procedure. SYMBOLS ■:Cautions and keypoints : Grease : Adhesive : Tool CONTENTS Page CONTENTS Page ■Preparation before AF adjustment --------------- 42 ■Precautions --------------------------------------------- 2 ①AF Area Adjustment --------------------------------- 43 ■Discharge ------------------------------------------------ 2...

  • Page 2: Precautions

    2 (2181) ■ ■ ■ ■ ■ Precautions Chemicals Handle chemicals of high volatility with care, use of which will affect to your health and environment. 1. Store them sealed in a specific place to prevent exposure to high temperature or direct sunlight. 2.

  • Page 3: To Inhibit Flash Charge

    (2181) 3 To inhibit flash charge Be sure to make flash charge available after repair. 1. Set up the camera as Fig. 2. 2. Select “ASSIST MODE” from main menu and press SELECT Button. 3. Select “FLASH CHARGE ON/OFF” from assist mode menu and press SELECT Button. 4.

  • Page 4: Disassembly Of The Exterior Parts

    4 (2181) 1. Disassembly of the exterior parts Disassemble it in order of step 1to 10. 9747-1740-07(2) 9747-1740-07(2) 9747-1740-07(2) 9747-1740-07(2) 9747-1740-07(2) TOP COVER ASSY TOP COVER ASSY TOP COVER ASSY TOP COVER ASSY TOP COVER ASSY Fig. 3 Fig. 3 Fig.

  • Page 5: Wires Arrangement

    (2181) 5 Fig. 1 Fig. 1 Removal the BACK COVER ASSY Removal the BACK COVER ASSY Fig. 2 Fig. 2 Removal the FRONT COVER ASSY Removal the FRONT COVER ASSY ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Removal the BACK COVER ASSY Removal the BACK COVER ASSY Removal the BACK COVER ASSY...
  • Page 6 6 (2181)

  • Page 7: Disassembly Of The Tebure Assy, Shutter Assy

    (2181) 7 2. Disassembly of the TEBURE ASSY, SHUTTER ASSY Disassemble it in order of step 1to 6. When CCD is out of position after replacing CCD ASSY, tighten 9761-2055-07(2) 9761-2055-07(2) 9761-2055-07(2) 9761-2055-07(2) 9761-2055-07(2) three AORI ADJ SCREW #2706 until they stop, then evenly loosen 1171 1171 1171...
  • Page 8 8 (2181) ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Removal Removal Removal Removal Removal the I/OFLEXIBLE ASSY the I/OFLEXIBLE ASSY the I/OFLEXIBLE ASSY the I/OFLEXIBLE ASSY the I/OFLEXIBLE ASSY I/O FLEXIBLE ASSY I/O FLEXIBLE ASSY I/O FLEXIBLE ASSY I/O FLEXIBLE ASSY...
  • Page 9 (2181) 9 Fig. 4 Fig. 4 Fig. 4 ■ ■ ■ ■ ■ Fig. 4 Fig. 4 SHUTTER SPACER SHUTTER SPACER SHUTTER SPACER SHUTTER SPACER SHUTTER SPACER ■ ■ ■ ■ ■ Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig.

  • Page 10: Disassembly Of The Mirror Box Assy, Battery Holder

    10 (2181) 3. Disassembly of the MIRROR BOX ASSY, BATTERY HOLDER Disassemble it in order of step 1 to 3. 9384-2190-50(2) 9384-2190-50(2) 9384-2190-50(2) 9384-2190-50(2) 9384-2190-50(2) (5x5mm) (5x5mm) (5x5mm) (5x5mm) (5x5mm) Fig. 1 Fig. 1 Fig. 1 ■ ■ ■ ■ ■ Fig. 1 Fig.

  • Page 11: Disassembly Of The Image Board Assy, Main Board Assy

    (2181) 11 4. Disassembly of the IMAGE BOARD ASSY, MAIN BOARD ASSY Disassemble it in order of step 1 to 11. 4908 4908 4908 4908 4908 ③ ③ ③ ③ ③ 9747-1745-07(4) 9747-1745-07(4) 9747-1745-07(4) 9747-1745-07(4) 9747-1745-07(4) 4901 4901 4901 4901 4901 9747-1745-01(3) 9747-1745-01(3)
  • Page 12 12 (2181) ■ ■ ■ ■ ■ Fig. 2 Fig. 2 Fig. 2 Fig. 2 Fig. 2 ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 4518 4518 4518 4518 4518 4520 4520 4520 4520 4520 4907...

  • Page 13: Disassembly-1 Of The Mirror Box Assy

    (2181) 13 5. Disassembly-1 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 9. 5022 5022 5022 5022 5022 See pg 7. See pg 7. See pg 7. See pg 7. See pg 7. 9747-1750-07(3) 9747-1750-07(3) 9747-1750-07(3) 9747-1750-07(3) 9747-1750-07(3)
  • Page 14 14 (2181) ■ ■ ■ ■ ■ Fig. 2 Fig. 2 Fig. 2 Fig. 2 Fig. 2 Fig. 1 Fig. 1 ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 DIOPTER SPRING DIOPTER SPRING DIOPTER SPRING DIOPTER SPRING DIOPTER SPRING DIOPTER CAM DIOPTER CAM...

  • Page 15: Disassembly-2 Of The Mirror Box Assy

    (2181) 15 6. Disassembly-2 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 7. 9749-2045-07 9749-2045-07 9749-2045-07 9749-2045-07 9749-2045-07 1171 1171 1171 1171 1171 See pg 13. See pg 13. See pg 13. See pg 13. See pg 13.
  • Page 16 16 (2181) APERTURE RING ASSY Removal/Installation Removal Turn APERTURE RING ASSY clockwise until it stops (Fig. 1). Now the ring can be removed. Be careful not to turn the aperture coupling gear in APERTURE BASEPLATE ASSY. Installation 1. Set APERTURE BASEPLATE ASSY to the default charge position referring to Charge Position Setting procedure (pg 18.), then install to FRONT FRAME ASSY.

  • Page 17: Disassembly-3 Of The Mirror Box Assy

    (2181) 17 7. Disassembly-3 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 8. 9747-1730-07(2) 9747-1730-07(2) 9747-1730-07(2) 9747-1730-07(2) 9747-1730-07(2) 2162-5111 2162-5111 2162-5111 2162-5111 2162-5111 2162-5110 2162-5110 2162-5110 2162-5110 2162-5110 2162-2517 2162-2517 2162-2517 2162-2517 2162-2517 2162-2519 2162-2519 2162-2519 2162-2519 2162-2519...
  • Page 18 18 (2181) ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 AF CHARGE ASSY Installation AF CHARGE ASSY Installation AF CHARGE ASSY Installation AF CHARGE ASSY Installation AF CHARGE ASSY Installation 1. Rotate the designated cam-gear in arrow direction while keep pushing the lever against it 1.
  • Page 19 (2181) 19 ■ ■ ■ ■ ■ Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 6 Fig. 6 ■ ■ ■ ■ ■ Fig. 6 Fig. 6 Fig. 6 MAIN MIRROR HOLDER ASSY MAIN MIRROR HOLDER ASSY MAIN MIRROR HOLDER ASSY 0513 0513...

  • Page 20: Disassembly Of The Top Cover Assy

    20 (2181) 8. Disassembly of the TOP COVER ASSY Disassemble it in order of step 1 to 26. (Continued to the next page) 1499 1499 1499 1499 1499 Fig. 4 Fig. 4 Fig. 4 ■ ■ ■ ■ ■ Fig. 4 Fig.
  • Page 21 (2181) 21 9749-1745-07 9749-1745-07 9749-1745-07 9749-1745-07 9749-1745-07 9762-2055-01(2) 9762-2055-01(2) 9762-2055-01(2) 9762-2055-01(2) 9762-2055-01(2) ② ② ② ② ② 9747-1735-07(2) 9747-1735-07(2) 9747-1735-07(2) 9747-1735-07(2) 9747-1735-07(2) 2162-0148 2162-0148 2162-0148 2162-0148 2162-0148 1141 1141 1141 1141 1141 9747-1730-07 9747-1730-07 9747-1730-07 9747-1730-07 9747-1730-07 1616 1616 1616 1616 1616 ⑭...
  • Page 22 22 (2181) Fig. 2 Fig. 2 Fig. 2 ■ ■ ■ ■ ■ Fig. 2 Fig. 2 Fig. 1 Fig. 1 Fig. 1 ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fit part-a of #2162-1474 between the longest Fit part-a of #2162-1474 between the longest Fit part-a of #2162-1474 between the longest Fit part-a of #2162-1474 between the longest Fit part-a of #2162-1474 between the longest...
  • Page 23 (2181) 23 ■ ■ ■ ■ ■ Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5 ■ ■ ■ ■ ■ Fig. 6 Fig. 6 Fig. 6 Fig. 6 Fig. 6 1. Install #2162-1475 to #2162-1470 fitting its 1. Install #2162-1475 to #2162-1470 fitting its 1.

  • Page 24: Disassembly Of The Back Cover Assy

    24 (2181) 9. Disassembly of the BACK COVER ASSY Disassemble it in order of step 1 to 11. 9384-2190-50 9384-2190-50 9384-2190-50 9384-2190-50 9384-2190-50 4903(2) 4903(2) 4903(2) 4903(2) 4903(2) (5x5mm) (5x5mm) (5x5mm) (5x5mm) (5x5mm) 4902(2) 4902(2) 4902(2) 4902(2) 4902(2) 9384-2290-90 9384-2290-90 9384-2290-90 9384-2290-90 9384-2290-90...
  • Page 25 (2181) 25 ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Stick #9384-2290-90 to the designated position. Stick #9384-2290-90 to the designated position. Stick #9384-2290-90 to the designated position. Stick #9384-2290-90 to the designated position. Stick #9384-2290-90 to the designated position.

  • Page 26: Disassembly Of The Ccd Assy, Dc Jack Holder

    26 (2181) 10. Disassembly of the CCD ASSY, DC JACK HOLDER If CCD ASSY (2181-1001) is exchanged for new one, exchange the bar code on the BACK SUS PLATE (2181-1001) for the bar code put on the new CCD ASSY. 4906 4906 4906...

  • Page 27: Disassembly Of The Card Cover Holder, Side Cover, Front Cover Assy

    (2181) 27 11. Disassembly of the CARD COVER HOLDER, SIDE COVER, FRONT COVER ASSY 1154 1154 1154 1154 1154 USB CARD COVER ASSY USB CARD COVER ASSY USB CARD COVER ASSY USB CARD COVER ASSY USB CARD COVER ASSY 9384-2290-90 9384-2290-90 9384-2290-90 9384-2290-90...

  • Page 28: How To Replace "Shutter Assy

    28 (2181) ■ ■ ■ ■ ■ How to replace "SHUTTER ASSY" By using this method for exchanging "SHUTTER ASSY", you do not have to perform adjustment of CCD perspective and adjustment of center part of CCD. 9611-1620-07 9611-1620-07 9611-1620-07 9611-1620-07 9611-1620-07 9761-2055-07(2)
  • Page 29 (2181) 29 ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 ■ ■ ■ ■ ■ Fig. 2 Fig. 2 Fig. 2 Fig. 2 Fig. 2 Solder Solder Solder Solder Solder Lead wires Lead wires Lead wires Lead wires Lead wires...

  • Page 30: Required Adjustment, Setting And Confirmation Items After Repairing (Exchanging Parts)

    30 (2181) Required adjustment, setting and confirmation items after repairing (exchanging parts) Adjust, set and confirm as the following table when the following parts are removed (exchanged). Follow the steps from the upper line to adjust. Parts REFLECTOR ASSY SHUTTER ASSY APERTURE ASSY CCD MODULE CCD ASSY...
  • Page 31 (2181) 31 Parts PENTA ASSY SPC HOLDER ASSY TEBURE ASSY AF CHARGE ASSY (0521) (0580) (0587) (0901) Adjustment/ Removed Replaced Removed Replaced Removed Replaced Removed Replaced Viewfinder Back ○ ○ ○ ○ ○ ○ ○ ○ SPC Position ○ ○ Manual Set SS ○...

  • Page 32: Related Adjustment And Required Setting Items

    32 (2181) Related adjustment and required setting items When each adjustment or setting is operated, be sure to follow the related adjustment and setting items listed blow. Number : Related adjustment items. Adjust and set in order of the number. : Related adjustment items.

  • Page 33: Using Hit System

    (2181) 33 Using HIT System Basic operation Before attaching the contact jig-* to or detaching from the camera, be sure to remove the power supply from the camera and turn off the HIT controller. In case of making a Data Copy of adjustment data, keep the controller activated. 1.

  • Page 34: Adjustment/Check Items Available With 2181 Rom Pack

    34 (2181) Adjustment/Check items available with 2181 ROM Pack <Main MENU> <MENU> <SUB MENU> ■ROM PACK FOR 2181 SS ADJ. (P.37) SPC ADJ. (P.38) PRETRIGGER ADJ. (P.39) PI- PR ADJ. PI-PR ADJ.(P.40) RESET MODE (P.41) RESET MODE 1 RESET MODE 2 AF ADJ.

  • Page 35: Viewfinder Back Adjustment

    (2181) 35 Viewfinder Back Adjustment Equipment Required 1000mm Collimator AE Master Lens Magnifier Adjustment 1. Set up the camera as in Fig. 1, so that the chart is at the center of viewfinder. 2. Set Master Lens to infinity. 3. Check that the chart is in focus. If not, Select one or two VB Washers, and install Washer(s) as in Fig.

  • Page 36: Manual Set Ss & X-Sync. Time-Lag Check

    36 (2181) Manual Set SS & X-Sync. Time-lag Check Equipment Required Shutter Tester Sync. Cable Manual SS Check 1. Set up the equipment as in Fig. 1. 2. Release the shutter at each shutter speed, and check that reading meets the table-1 below. X Sync.

  • Page 37: Manual Set Ss Adjustment

    (2181) 37 Manual Set SS Adjustment Equipment Required Shutter Tester HIT Controller ROM Pack for 2181 Contact Jig for 2181 I/F Box for HIT Contact Jig Cable Adjustment 1. Set up the equipment as in Fig. 1. 2. Set the shutter speed to 1/4000 sec and release the shutter several times, then calculate an average of readings at B-Range.

  • Page 38: Spc Position Adjustment

    38 (2181) SPC Position Adjustment Peform this adjustment without TOP COVER ASSY, after disassembling from step 1 to step 9 in P.4, by using Remote cord. Equipment Required Master Lens HIT Controller ROM Pack for 2181 Contact Jig for 2181 Contact Jig Cable I/F Box for HIT SPC Chart for 2181...

  • Page 39: Aperture Preset Check/Adjustment

    (2181) 39 Aperture Preset Check Equipment Required HIT Controller ROM Pack for 2181 Contact Jig for 2181 Contact Jig Cable I/F Box for HIT HIT I/O Tester Preset Signal Adapter Check 1. Set up the equipment as in Fig. 1, and set camera to "M" mode and "Bulb". 2.

  • Page 40: Pi-Pr Adjustment

    40 (2181) PI-PR Adjustment To read output level of sensor devices for aperture (F PI), AF/MF (AFM PR) and focus (AF PI). Equipment Required HIT Controller ROM Pack for 2181 Contact Jig for 2181 I/F Box for HIT Contact Jig Cable AC adpter AC-11 Adjustment 1.
  • Page 41 (2181) 41 How to Handle RESET MODE Caution: This MODE must be used only when PI-PR adjustment fails and camera is not functional at all. If camera is not functional at all, you can not do switch on or off camera power or you can not release at all by the communication failure.

  • Page 42: Preparation Before Af Adjustment

    42 (2181) Preparation before AF adjustment Note: After replacing CCD MODULE ASSY and/or MIRROR BOX ASSY or its relative parts, always perform adjustment 1 to 4 (pg. 43-46). If customer says focus fucntion is not normal, perform this adjustment too. Preparations The following items should have been completed before starting AF adjustment.

  • Page 43: ①Af Area Adjustment

    (2181) 43 ① ① ① ① ① AF Area Adjustment Adjustment 1. Set up the equipment as in Fig. 1. 2. Select "AREA ADJ." from the main menu and press SELECT Button. 3. Press and hold Shutter-release Button partway down after Naviagation Display goes out, so that lines with two dents and a value appear in the display and remain for 3 sec.

  • Page 44: ② Pitch Yaw Adjustment

    44 (2181) ② ② ② ② ② Pitch Yaw Adjustment Turn a flood lamp toward camera during Pitch Yaw Adjustment. How to Peform Adjustment Pitch Adjustment 1. Attach AF-Y/P Adjuster to the camera, and set Pitch Adjusting Plate as in Fig. 1. 2.

  • Page 45: ③ Ez Check

    (2181) 45 ③ ③ ③ ③ ③ EZ Check Check 1. Set up the equipment as in Fig. 1. 2. Select "EZ CHECK" from the main menu and press SELECT Button. 3. Select the desired island group from the menu, then press SELECT Button. Use the appropriate chart according to the desired island group.

  • Page 46: ④Ez Adjustment

    46 (2181) ④ ④ ④ ④ ④ EZ Adjustment Be sure to perform the adjustment for all island groups in series according to the display after replacing CCD MODULE ASSY. If ERROR (communication failure with HIT) occurs during adjustment, start over from the item that has been interrupted.

  • Page 47: Assist Mode

    (2181) 47 Assist MODE Equipment Required HIT Controller ROM Pack for 2181 Contact Jig for 2181 I/F Box for HIT Contact jig Cable The following 2 assistant items are available. TROUBLE CODE FLASH CHARGE ON/OFF Preparation 1. Set up the equipment as in Fig. 1. 2.

  • Page 48: Preparing The 2181 Adjustment Program

    48 (2181) Preparing the 2181 adjustment program PC for use The PC loaded on either Windows 98/98SE, 2000 Professional or XP and USB terminal originally 40MB or more of available memory and 15MB or more of available hard-disk space VGA or more monitor capable of displaying at least 32,000 colors Details of the 2181 adjustment program CD 2 1 8 1 a d ju s tm e n t p ro gra m C D U S B 2 .0...

  • Page 49: Starting Up The 2181 Adjustment Program (In The Adjustment Mode)

    (2181) 49 Starting up the 2181 adjustment program (in the adjustment mode). Outline Connect the camera and PC with USB-2 and start up the camera in the "adjustment mode." "Adjustment mode" means the condition of that the camera can contact with the 2181 adjustment program in the PC.

  • Page 50: Back Up Flash Rom Data Of Master Body

    50 (2181) Back up Flash ROM data of Master Body Save flash ROM data of master body (Mass production camera body of #2181), which is used for adjustment of CCD ceter position and adjustment of white balance, to PC. If flash ROM data of master body is over written by mistake, load flash ROM data from PC and re-write flash ROM data of master body.

  • Page 51: Adjustment Of Ccd Vsub Voltage

    (2181) 51 Adjustment of CCD Vsub voltage Memorize the number printed on the bar code put on the CCD ASSY, when CCD ASSY (2181-0271) or MAIN BOARD ASSY (2181-0455) is replaced. If CCD ASSY (2181-1001) is exchanged for new one, exchange the bar code on the BACK SUS PLATE (2181-1001) for the bar code put on the new CCD ASSY.

  • Page 52: Setting Of Master Body And Chart For The Adjustment Of Ccd Position

    52 (2181) Setting of Master body and chart for the adjustment of CCD position Required equipment AF Master Lens Master body (Production body of #2181) 2181 AORI-Chart Grip Ring Tripod USB-2 (USB cable) AC Adapter AC-11 Setting the Master body and the chart 1.

  • Page 53: Adjustment Of Ccd Position And Perspective

    (2181) 53 Adjustment of CCD position and perspective Outline Peform adjustment of CCD position and perspective. *See Setting the camera and the chart when adjusting the CCD perspective (P. 52). Required equipment Fluorescent light stand SQ967W PC with preinstalled the 2181 adjustment program CF card for Adjustment Master body USB-2 (USB cable)
  • Page 54 54 (2181) ■ ■ ■ ■ ■ Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 ■ ■ ■ ■ ■ Fig. 2 Fig. 2 Fig. 2 Fig. 2 Fig. 2 AORI adjusting screws AORI adjusting screws AORI adjusting screws AORI adjusting screws AORI adjusting screws Numbers mean the degrees of rotating adjusting screw...

  • Page 55: Adjustment Of The Frequency For Camera Shaking (Act Drv Freq)

    (2181) 55 Adjustment of the frequency for camera shaking (ACT DRV FREQ) Required equipment PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-2 (USB cable) AC Adapter AC-11 Preparation of the adjustment Set camera to adjustment mode. Refer to “Starting up the 2181 adjustment program (in the adjustment mode)”...

  • Page 56: Adjustment Of The Ae (Ae)

    56 (2181) Adjustment of the AE (AE) Required equipment Luminance box L-2101/L-2111 or multi camera tester: EF-8301 Master Lens PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-2 (USB cable) AC Adapter AC-11 Preparation of the adjustment 1.

  • Page 57: Sensitivity Adjustment (Gain)

    (2181) 57 Sensitivity adjustment (GAIN) Required equipment Luminance box L-2101/L-2111 or multi camera tester: EF-8301 Master Lens PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-2 (USB cable) AC Adapter AC-11 Preparation of the adjustment 1. Set camera to adjustment mode. Refer to “Starting up the 2181 adjustment program (in the adjustment mode)”...

  • Page 58: Adjustment Of The Defective Pixel (Defect Pixel)

    58 (2181) Adjustment of the defective pixel (DEFECT PIXEL) Required equipment Luminance box L-2101/L-2111 or multi camera tester: EF-8301 Master Lens PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-2 (USB cable) AC Adapter AC-11 Preparation of the adjustment 1.

  • Page 59: Adjustment Of White Balance (Wb)

    (2181) 59 Adjustment of white balance (WB) Required equipment Light Source-A. Refer to Light source-A maintenance, P. 62. Light balancing filter LB200 Master body (Mass Production camera) Master Lens PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-2 (USB cable) AC Adapter AC-11 White chart...

  • Page 60: Adjustment Of The Camera Shaking Compensation (Shake Gain)

    60 (2181) Adjustment of the camera shaking compensation (SHAKE GAIN) Required equipment Vibration tester Shake Offset Chart 2 PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-200 (USB cable) AC Adapter AC-11 Master Lens for SHAKE Preparation of the adjustment 1.

  • Page 61: Distination Seting(Distination)

    (2181) 61 Setting of Destination (DESTINATION) *Always perform the setting and confirming the destination. Required equipment PC with preinstalled the 2181 adjustment program CF card for Adjustment USB-200 (USB cable) AC Adapter AC-11 Preparation of the adjustment Set camera to adjustment mode. Refer to “Starting up the 2181 adjustment program (in the adjustment mode)”...

  • Page 62: Light Source-A Maintenance

    62 (2181) Light Source-A Maintenance OutLine Because high accuracy of required light source-A is required when adjusting and confirming. Measuring instrument Chroma meter (CL-200) Liminance meter (LS-100) Light source-A (tungsten light) Procedure *Managements of the chromaticity and the luminance 1. Light the light source-A on. 2.

  • Page 63: Error Code On Adjustment Program

    (2181) 63 Error code on adjustment program Error Code list of 2181 ROM PACK Item Err Code Discription Reason Manual Set SS Input illegal value SHUTTER ASSY trouble Aperture Preset No change on Aperture Pulse APERTURE ASSY trouble Error Code List of PC Adjustment program Discription about adjustment NG Code ０ｘ００００００００...
  • Page 64 64 (2181) Adjustment (Common) Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system) Adjustment (ANTI-SHAKE system) 0x90****** 0x**00**** At the time of a successful adjustment NG for CCD CENTER Adjustment   0x**01**** Setting of Camera 0x**f0**** Arguments are not good. (Not camera errors）   0x**02**** Communication for SHAKE compensation 0x**f1****...

  • Page 65: Measuring Instrument

    (2181) 65 Measuring instrument PC (AT convertible) with preinstalled Windows 98, 98SE, 2000 or XP. (USB port should be guaranteed its performance by the maker. Also, Adobe Photoshop 6.0 or later should be installed if Windows 2000 or XP is installed on PC.) * It is possible to confirm the performance on PC with Windows 95 (AT convertible).

  • Page 66: Subsidiary Materials

    66 (2181) 2181 adjustment program CD (Ver. 1.0) 2181 adjustment program CD (Ver. 1.0) 2181 adjustment program CD (Ver. 1.0) Master Lens for Shaking Master Lens for Shaking 2181 adjustment program CD (Ver. 1.0) 2181 adjustment program CD (Ver. 1.0) Master Lens for Shaking Master Lens for Shaking Master Lens for Shaking...

Table of Contents