Page 1
American Operator's Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
Assembly Parts List #2 ... 23 Assembly Drawing #3 ... 24 Assembly Parts List #3 ... 25 Accessories Drawing & Parts List ... 26 Chatter-Wave Prevention ... 27 Page 2 Contents of this Book AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Keep all fasteners tight. Keep adjustments according to machine specifications. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual AVERTISSEMENT ADVERTENCIA...
Page 4
DANGER: Electrocution or injury could occur if the power cord is run over or damaged by the sander. Keep the cord free from under the machine to avoid contact with the sandpaper. Always lift the power cord over the machine.
Always consult with the flooring manufacturer on the proper installation, preparation, and finishing of their product. Determine suitability of your equipment in preparing the product. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Operating Controls Operating Controls Leveling Adjustment...
If motor appears to labor or takes a considerable longer time to come up to speed reduce sanding pressure. Page 6 Feet/Wire Guage (Stranded Copper) 0 - 100' 100 - 250' Use Voltage Booster AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
3. Resecure the motor to the chassis. 4. Install the fan belt. 5. Install the belt cover. 6. Reconnect the handle plug. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Figure 1 Figure 2 Page 7...
5. Fold the other end of the abrasive over the end of the template and crease. 6. Repeat steps 4 and 5 for remaining notch. 7. Lift the drum cover. Page 8 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Page 9
NOTE: When using #4 or 4½ grit abrasive, remove the large grains from the folded ends. To remove the grains, rub the folded ends together. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Figure 3 Figure 4 Page 9...
Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to counter- sink all nails before sanding floors. Page 10 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Page 11
Stagger the termination points for a better blend when edging. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Figure 5 8. Empty dust bag whenever it is 1/3 full. Never leave a dust bag unattended with sanding dust in it.
Page 12
C. Second pass forward, overlap ½ the drum width. Second pass reverse, retrace second path forward, etc...for the entire room E. Work the remaining unsanded floor in the same fashion, right to left. Figure 6 Page 12 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
150 grit For final sanding of certain conifers where a smooth surface is desired. 180 grit For surface roughing between coats of finish. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Abrasive Bulk Roll Part No. 945516 945517 945518...
6. Tighten belt and secure motor to chassis. 7. Install the fan belt. 8. Install the belt guard. Page 14 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Page 15
1. Loosen the locknut on the control rod. See figure 9. 2. Screw the control rod adjuster out until desired reach is found. 3. Tighten the locknut. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Figure 7 Figure 8 Figure 9 Page 15...
Idler pulley after 1st 1500 hrs. Fan shaft after 1st 2500 hrs. Arbor shaft after 1st 5000 hrs. Motor shaft after 1st 5000 hrs. Page 16 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Ref No. Part No AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual AMERICAN SANDERS TECHNOLOGY Model American 12 Floor Sander Parts List #1 Handle Asembly 10/00 Description Ref. Cord Assembly 41706A Connector (NEMA) 962065 Screw - 8-32 x ¼ Pn St Mach...
Page 22 AMERICAN SANDERS TECHNOLOGY Model American 12 Floor Sander Drawing #2 10/00 AMERICAN SANDERS TECHNOLOGY - American 12 Floor Sander Owner's Manual...
Part # Description 50563A End Bell 52768A Front Cover 53998A 52769A Fan Cover AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual Model American 12 Floor Sander Parts List #2 10/00 Ref # Part No. 962288 67816A 20401B 67815A 68101A...
55 u NOTE: u indicates a change has been made since the last publication of this manual. AMERICAN SANDERS TECHNOLOGY -American 12 Floor Sander Operator's Manual AMERICAN SANDERS TECHNOLOGY American 12 Floor Sander Assembly Parts List #3 6/01 Description 88502A...
American Sanders Technology’s Sander 16. To minimize chatter when using a belt or drum sander the following steps should be taken: 1) DRUM PAPER...insure the paper is secured in the slot, but not too tight. Paper that is too tight will force the drum slot wider, leaving a “slot mark chatter”...
Page 28
Take a heavier cut and increase the pace. 5) DEBRIS... lodged between the paper and the drum will leave chatter. On a belt sander, debris may be adhered to the drum. Insure the drum is clean and free of debris before placing the paper on.
Page 29
ALTO U. S. A. Locations HEAD OFFICE ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S.
Page 30
AMERICAN SANDERS TECHNOLOGY U.S. WARRANTY This American Sanders Technology Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with American Sanders Technology's Maintenance and Op- erations Instructions.