Page 1
The Wanderer™ Cordless Key Telephone RI NG IN G U s e r G u i d e...
Page 3
The Wanderer™ Cordless Key Telephone Unit U s e r G u i d e Issue 1 - August, 2002 P/N: 9018-10...
Page 4
Copyright Laws of the United States (17 U.S.C. Section 101 et. seq.). VODAVI reserves the right to make changes in specifications at any time and without notice. The information furnished by VODAVI in this material is believed to be accurate and reliable, but is not warranted to be true in all cases.
Cordless Capabilities … and … Digital Quality For maximum clarity and range, the Wanderer’s Digital Spread Spectrum Technology spreads the signal over one of 40 independent frequency ranges. A pre-assigned digital code is shared by the charging base and handset to prevent other radiated frequencies from interfering with system sound quality.
Product Overview About the Wanderer Product Overview The Handset is a lightweight design with an easy-to-read display and comfortable soft keypad buttons. Handset features also include: 10 Interactive Feature Buttons: C O N F O F F F L A S H...
1. Plug the power adaptor into a wall outlet. Plug the other end into the charging base where it is labeled DC IN 12V. 2. Turn the switch on the bottom of the Wanderer to the ON position and place the handset in the charging base.
Register Station Number to Handset Although station number registration is automatic … use this procedure to prevent a “previously saved number” from appearing on the Wanderer display (e.g., new ext. number). From your Wanderer, perform the following steps: 1. Press [HOLD].
Using Your New Wanderer Review this section for step-by-step operating instructions. When to Recharge Handset The Wanderer will send an audible alert to indicate recharging. Talk Time You can talk for approximately 4 hours on your Wanderer before recharging is necessary.
Both the telephone and the Wanderer audibly ring if the handset is not in the charging base and is turned ON. » Only 1 call may be put on hold at a time on the Wanderer . » Calls may not be placed from your cordless handset while the telephone is active.
Button Features Using Your New Wanderer Button Features This section describes how to use each of the Wanderer’s ten feature buttons. CONFERENCE Button A conference call supporting up to eight parties can be originated from the Wanderer. To initiate a conference call: 1.
FLEXIBLE Button The Flexible Button (FLEX) on the Wanderer may be assigned to function as one of the 24 flexible buttons on your telephone. The desired feature must be programmed as a button on the telephone prior to activating the FLEX button on the Wanderer.
2. Press [ON/OFF] on the Wanderer. 3. Press [HOLD] to pick up the call on the Wanderer. To process multiple calls from your Wanderer: 1. Press [HOLD] to place your call on hold. An intercom dial tone is heard.
The handset must be turned ON and removed from the charger base. To activate handset, press [ON/OFF]. LCD will display Search. Once the base is located, the display will indicate Talk. If the Wanderer is unable to find the base … three short beeps will sound.
SPEED Button Using Your New Wanderer SPEED Button You may assign Speed Dial numbers on your Wanderer to provide speedy access to frequently-used telephone numbers. To program a speed dial number: 1. Press [ON/OFF]. 2. Press [SPEED] + [SPEED], then enter the Bin Number. 3.
TRANSFER Button Using Your New Wanderer TRANSFER Button External and internal calls may be transferred to idle or busy stations by performing the following steps: S CR E E N E D T R A NS F E R While on a call: 1.
For added security, only the [#] sign appears on the LCD display. Ringing Signal The audible ring signal on the Wanderer can identify the type of incoming call as internal or external. Internal Ring Signal … a single ring is repeated.
LED Indicators Using Your New Wanderer LED Indicators The LED indicators on the charging base function as follows: Power … lights when the base is properly plugged in Talk … lights during an active call Call … pulses when the Pager Call button is activated Charger …...
Page 21
LCD Displays Using Your New Wanderer CALL FWD (ALL) TO ACD/UCD GRP CALL FWD (BUSY) TO HUNT GRP F O R W A R D E D B U S Y F W D U C D X X X X H U N T X X X X CALL FWD (ALL) TO HUNT GRP...
Page 22
LCD Displays Using Your New Wanderer CO LINE NUMBER IS RECALLING OFF-HOOK VOICE OVER ANNOUNCEMENT FROM A STA L I N E X X X A N N O U N C E R E C A L L I N G F R O M X X X X DO NOT DISTURB - You are in DND...
Page 23
LCD Displays Using Your New Wanderer Wanderer Displays … while using Keyset ACD/UCD CIQ - Keyset on CO Line Call ACD/UCD CIQ - Keyset on Internal Call (with incoming calls) CONFERENCE CALL X X X X C I Q : C C C O N F E R E N C E A L : a a O C : o o o...
Page 24
LCD Displays Using Your New Wanderer OFF-HOOK VOICE OVER ANNOUNCE TO ANOTHER STA RECORDING MODE A N N O U N C E R E C O R D I N G S T A X X X X OUT OF SERVICE (called Sta is OOS) RECORDING SETUP S T A X X X X...
Why can’t I make a call from my The Wanderer cannot locate its charging base for one of the following reasons: Wanderer? When I press the ON/OFF button to make a call, the LCD...
Page 26
CKTU mode, why Version 1.11 or greater for XTS systems, doesn’t the Wanderer display update or version 4.11 or higher for other Vodavi with digital keyset information? key systems, must be installed to enable CKTU mode and use the Wanderer.
Page 28
WE’RE TALKING TECHNOLOGY www.vodavi.com Part Number: 9018-10...