Advanced Remote Operations; Operating One Component While Using Another (Background Operation); Changing The Factory Setting Of A Function Button - Sony STR-DA80ES Operating Instructions Manual

Advanced Remote Operations

Advanced Remote Operations
Operating One Component
While Using Another
(background operation)
You can temporarily operate other components while
listening to or watching a program.
BACKGROUND
1
Hold down BACKGROUND.
2
Press both the corresponding button of the
component you're going to use (see the table
below) and one of the following buttons at the
same time; VISUAL POWER, TV/VIDEO, CH/
PRESET +/–, ANT TV/VTR, D.SKIP, (, 9, p,
0/), =/+, P, r.
Example: To start recording on a tape deck
while listening to a CD
While holding down BACKGROUND,
press 4 (or 5) and press r + ( at the
same time.
The following buttons correspond to the
components.
The button
1
2
3
4
5
6
7
8
9
>10
ENTER
*
Sony VCRs are operated with a VTR 1, 2 or 3 setting
that corresponds to Beta, 8mm, and VHS,
28
respectively.
SYSTEM OFF
VISUAL
SLEEP LEARN POWER
SYSTEM CONTROL / FUNCTION
VIDEO 1 VIDEO 2 VIDEO 3 LD TV
(AUTO CATEGORIZE SYSTEM)
TAPE DAT/MD CD TUNER PHONO
TV 5.1
CONTROL INPUT
1 2 3
ON
TV/VIDEO
4 5 6
Numeric and
D.TUNING
DISC
7 8 9 +
ENTER buttons
BACK CH/
GROUND SHIFT ENTER PRESET
> 0 –
10
RMS/START
ANT
– +
SUB CH POSITION SWAP TV/VTR
0 ) = +
D. SKIP
— RMS —
DIRECTION CLEAR P IN P JUMP
9 ( p P r
— SOUND FIELD — TEST
ON/OFF GENRE MODE TONE
EQ/
TONE BAND SLOPE — LEVEL —
+ +
REAR CENTER
DIGTAL DIRECT
PROCESSING
– –
CONTROL
MASTER
BASS
VOL
BOOST
DPC
MODE
MUTING
PROGRAMMABLE
Corresponds to
CD player
DAT deck
MD deck
Tape deck A
Tape deck B
LD player
VCR (remote control mode VTR 1
VCR (remote control mode VTR 2
VCR (remote control mode VTR 3
DBS tuner
DVD player
Changing the Factory Setting
of a FUNCTION Button
If the factory settings of the FUNCTION buttons (page
14) don't match your system components, you can
change them. For example, if you connect a Sony LD
player to the VIDEO 2 jacks, you can assign the VIDEO
2 button to set the remote to control the LD player.
Note that the settings of the TUNER and PHONO
buttons cannot be changed.
Numeric
and ENTER
buttons
1
Hold down the SYSTEM CONTROL/FUNCTION
button whose function you want to change
(VIDEO 2, for example).
2
Press the corresponding numeric button of the
component you want to assign to the SYSTEM
CONTROL/FUNCTION button (6 - LD player,
for example).
For the numeric buttons, see the table in
"Operating One Component While Using
Another" on this page.
Now you can use the VIDEO 2 button to control
your Sony LD player.
To reset the setting to the factory setting
Repeat the above procedure.
*
)
*
)
*
)
SYSTEM OFF
VISUAL
SLEEP LEARN POWER
SYSTEM CONTROL / FUNCTION
SYSTEM
VIDEO 1 VIDEO 2 VIDEO 3 LD TV
(AUTO CATEGORIZE SYSTEM)
TAPE DAT/MD CD TUNER PHONO
CONTROL/
TV 5.1
CONTROL INPUT
1 2 3
ON
FUNCTION
TV/VIDEO
4 5 6
D.TUNING
DISC
7 8 9 +
BACK CH/
GROUND SHIFT ENTER PRESET
0
> –
10
RMS/START
ANT
– +
SUB CH POSITION SWAP TV/VTR
0 ) = +
D. SKIP
— RMS —
DIRECTION CLEAR P IN P JUMP
9 ( p P r
— SOUND FIELD — TEST
ON/OFF GENRE MODE TONE
EQ/
TONE BAND SLOPE — LEVEL —
+ +
REAR CENTER
DIGTAL
DIRECT
PROCESSING
– –
CONTROL
MASTER
BASS
VOL
BOOST
DPC
MODE
MUTING
PROGRAMMABLE