Step 4: Connecting The Audio Cords; Step 6: Preparing The Remote - Sony RDR-HX715 Service Manual

QQ
3 7 63 1515 0

Step 4: Connecting the Audio Cords

Select one of the following patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver). This will enable you to listen to sound.
A Connecting to audio L/R (left/right) input jacks
This connection will use your TV's or stereo amplifier's (receiver's) two speakers for sound. You can
enjoy the following surround effects (page 61).
• TV: Dynamic, Wide, Night
• Stereo amplifier (receiver): Standard, Night
B Connecting to a digital audio input jack
If your AV amplifier (receiver) has a Dolby
connection. You can enjoy Dolby Digital (5.1ch) and DTS (5.1ch) surround effects.
LINE OUT
R-AUDIO-L
1
2
VHF/UHF
IN
DIGITAL OUT
PCM/DTS/
SET TOP DOLBY DIGITAL
BOX
OUT CONTROL
HDMI cord
(not supplied)
HDMI OUT
DIGITAL OUT
COAXIAL
PCM/DTS/
DOLBY DIGITAL
OPTICAL
Optical digital cord (not supplied)
[Speakers]
Rear (L)
Front (L)
Center
: Signal flow
TE
L 13942296513 * The yellow plug is used for video signals (page 18).
20
Step 6: Preparing the
Remote
You can control the recorder using the supplied
remote. Insert two size AA (R6) batteries by
matching the 3 and # ends on the batteries to the
markings inside the battery compartment. When
using the remote, point it at the remote sensor
on the recorder.
b
Notes
• If the supplied remote interferes your other Sony DVD
recorder or player, change the command mode number
for this recorder (page 24).
• Use the batteries correctly to avoid possible leakage
and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an extended
period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid inside
the battery compartment, and insert new batteries.
• Do not expose the remote sensor (marked
front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.
www
.
22
http://www.xiaoyu163.com
*1 *2
Digital or DTS decoder and a digital input jack, use this
(red) (yellow)
INPUT
Audio/video cord
(supplied)
(white)
(white)
(red)
(yellow)* AUDIO
to LINE OUT (R-AUDIO-L) 1 or 2
VIDEO S VIDEO
TV, projector, or AV
amplifier (receiver)
DVD recorder
HDMI OUT G-LINK COMPONENT
VIDEO OUT
COMPONENT
VIDEO IN
Y Y
LINE IN LINE OUT
VIDEO S VIDEO VIDEO S VIDEO
R-AUDIO-L R-AUDIO-L
COAXIAL
1 P 1 P
B B
3 P R 2 P R
OPTICAL
~ AC IN
to DIGITAL OUT (COAXIAL or OPTICAL)
Coaxial digital cord (not supplied)
or or
to coaxial or
[Speakers]
optical/HDMI
digital input
Rear (R)
Front (R)
AV amplifier (receiver)
with a decoder
Subwoofer
Controlling TVs with the remote
You can adjust the remote's signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier's (receiver's) volume.
b
Notes
• Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
1 2 3
Number
4 5 6
buttons, SET
7 8 9
0
WIDE MODE
on the
1
Slide the TV/DVD switch to TV.
2
Hold down [/1.
3
Enter your TV's manufacturer code (see
"Code numbers of controllable TVs"
below) using the number buttons.
x ao
y
i
http://www.xiaoyu163.com
8
z Hint
For correct speaker location, see the operating
instructions supplied with the connected components.
b
Notes
• Do not connect your TV's audio output jacks to the
LINE IN (R-AUDIO-L) jacks at the same time. This
will cause unwanted noise to come from your TV's
speakers.
• In the connection A, do not connect the LINE IN (R-
AUDIO-L) and LINE OUT (R-AUDIO-L) jacks to
your TV's audio output jacks at the same time. This
will cause unwanted noise to come from your TV's
speakers.
• In the connection B, after you have completed the
connection, make the appropriate settings under
"Audio Connection" in "Easy Setup" (page 25).
Otherwise, no sound or a loud noise will come from
your speakers.
A
• With the connection B, the surround sound effects of
this recorder cannot be used.
VIDEO
• When you connect the recorder to an AV amplifer
(receiver) using an HDMI cord, you will need to do one
L
of the following:
– Connect the AV amplifier (receiver) to the TV with
the HDMI cord.
R
– Connect the recorder to the TV with a video cord
other than HDMI cord (component video cord,
S VIDEO cord, or audio/video cord).
*1
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
*2
"DTS" and "DTS Digital Out" are trademarks of
Digital Theater Systems, Inc.
B
Q Q
3 6 7 1 3
4
Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
Buttons
[/1
VOL +/–
CH +/–
WIDE MODE
TV/VIDEO
Number buttons
TV/DVD switch
and SET
[/1
Code numbers of controllable TVs
CH +/–
If more than one code number is listed, try
VOL +/– entering them one at a time until you find the one
that works with your TV.
TV/VIDEO
Manufacturer
Sony
Akai
AOC
Centurion
Coronado
Curtis-Mathes
Daewoo
Daytron
Fisher
General Electric
Gold Star/LG
Hitachi
J.C.Penney
JVC
KMC
u163
Magnavox
Marantz
MGA/Mitsubishi
.
NEC
Panasonic
1-5
2 9 9 4 2 8
Step 5: Connecting the
Power Cord
Connect the supplied power cord to the AC IN
terminal of the recorder. Then plug the recorder
and TV power cords into an AC outlet. After you
connect the power cord, you must wait for a
short while before operating the recorder.
You can operate the recorder once the front panel
display lights up and the recorder enters standby
mode.
If you connect additional equipment to this
recorder (page 28), be sure to connect the power
cord only after all connections are complete.
~
1
1 5 0 5 8 2 9 9 4
Manufacturer
Philco
Philips
Operations
Pioneer
Turns your TV on or off
Portland
Adjusts the volume of
your TV Proscan
Selects the channel on
Quasar
your TV
Radio Shack
Switches to or from the
RCA
wide mode of a Sony
wide-screen TV
Sampo
Switches your TV's
Samsung
input source
Sanyo
Selects the channel on
Scott
your TV
Sears
Sharp
Sylvania
Teknika
Toshiba
Code number
Wards
01 (default)
Yorx
04
Zenith
04
12
03
12, 14
04, 22
03, 12
11
04, 06, 10
03, 04, 17
02, 03, 04
m
04, 10, 12
09
03
co
03, 04, 08, 12, 21
04, 13
04, 12, 13, 17
04, 12
06, 19
9 9
AC IN
to AC IN
2
to AC outlet
2 8 9 9
21
Code number
02, 03, 04, 08
08, 21
06, 16
03
10
06, 18
05, 10, 14
04, 10
12
03, 04, 12, 20
11, 14
12
07, 10, 11
03, 05, 18
08, 12
03, 08, 14
07, 18
03, 04, 12
12
14, 15
,continued
23