Understanding The Control Panel - Indesit W 104 T Instructions For Installation And Use Manual

Here I'm in command
Making the right choice is important. And it's easy.
Programme selector knob
and programmed start
Use this knob to select the wash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Now press on/off button G
(position I), pilot lamp H will start
flashing.
After 5", the setting will be
accepted, pilot lamp H will stop
flashing (staying lit) and the wash
cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset) and wait
5" : when the cancellation has
been accepted, pilot lamp H
flashes, and you can then turn the
appliance off.
You can use this knob to delay
the appliance's operation.
Select one of the four delay time
positions, press the on/off button
G (position I) and wait 5". The
setting has now been accepted
(pilot lamp H stays lit) and you
can select the programme you
desire.
Pilot lamp H has a particular
flashing motion (2" on and 4" off)
to indicate that a delayed start
has been set.
During this phase, you can open
the appliance door and change
the washing load, should you
wish to do so.
After the wash cycle has been set
and accepted by the washing
machine, turning the knob will
have no effect (except for when
it is on position Stop/Reset).
The detergent dispenser with the
additional bleach compartment
is here.
Instructions for installation and use
15
C
Temperature control knob
It is used to set the wash tempe-
rature in the recommended
programme table on pag. 16. It
also allows you to reduce the tem-
perature recommended for the
selected programme, and even to
set a cold wash cycle ( ).
Detergent dispenser
It is divided into three
compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle
wash;
3. Fabric conditioner.
The washing machine is
equipped with an extra
compartment 4 (provided as an
accessory) for the bleach, to be
inserted in compartment 1.
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
You can use it with programmes
3-4 (Cotton), 5-6 (Synthetics)
and 8-9 (Delicates).
Press this button
programmes 5-6-8-9 and the
wash cycle will come to a stop
on symbol .
4
3
2
1

Understanding the control panel

D F
E
You can complete it by pressing
button D again.
Important: this function should
not be used when button F (Stain
removal) has been pressed.
Slow spin
Use this button to reduce the
spinning speed from 1000 to
500 rpm for the cotton
programmes and from 850 to
500 rpm for the synthetic
fabrics programmes.
Stain removal (see page 19)
Thanks to this command, the
washing machine will carry out
a more intensive wash that
optimises the effectiveness of the
liquid additives, thus allowing
more resistant stains to be
removed. When you press the
stain removal button, you cannot
activate the pre-wash.
On-off
When button G is pressed, the
washing machine is switched
on, when it is not the machine
is switched off.
Turning the appliance off
in
does not cancel the selected
programme.
The on-off lamp
Lamp H flashes when the
appliance is switched on and
awaiting a programme to be set.
A steady light means the
appliance has accepted the
selected programme.
H I
B
G
The door block lamp
The safety lamp indicates that the
washing machine door is locked
to prevent it from being opened
accidentally. To avoid any
damages to lock mechanism,
you must wait for the lamp to
extinguish, before attempting to
open the door which takes around
three minutes.
A