Pioneer DJM-500 Service Manual page 42

DJM-500
CI Monitor Monaural/Stereo Selecor Switch
(MONO/STEREO)
Qg Monitor Equalizer Knob (MONITOREQ)
Used to obtain the beat easily with the headphone moni-
tor sound.
Increases/decreases low tone.
Flat at center click,
Increases when rotated to the right. (To + 12 dB at 100 Hz)
Decreases when rotated to the left. (To -12 dB at 100 Hz)
Qj Monitor Level Knob (MONITOR LEVEL)
Used for adjusting the headphone monitor volume.
Not affected by the master volume and master balance.
~ Headphone Terminal (PHONES)
ó) Channel Fader Volume
Used for adjusting the volume of CHl to CH4.
Q3 Assign Switch (ASSIGN Ai B)
When performing cross fader using two sources (A, B),
select the channels (CH1 to CH4) to be assigned to A
and B.
Effective when the cross fader switch (Qì) is on (cross
fader mix).
Q§ Fader Start Switch (FADER START) (Refer to
Page 17.)
When the optional CD player (CDJ-500G or CDJ-500lI)
is connected to the unit using the control cord, this
ON/OFF switch is used to start automatic playing of
the CD player using the channel fader or cross fader.
Q§ Cross Fader Volume (CROSS FADER)
Adjusts the mix volume of the sources set to A and B
using the assign switch (~).
Ql Cros Fader Swich (CROSS FADER ON/OFF
OFF:
Selec when mixing sounds using the channel fader volume.
(Direc mix.)
ON:
Select when mixing sounds using the cross fader. (Cross
fader mix.)
Ql Master Volume Level Adjustment
Used to adjust the level of the master output volume.
When the cross fader is ON, the sounds of assigns A, B
and main microphone will be output.
When the cross fader is OFF, the sounds of each channel
and main microphone wil be output.
58
~ Master Balance Knob (MASTER BALANCE)
Used to adjust the left and right balance of the master
output.
~ Booth Monitor Level Knob (BOOTH MONITOR
LEVEL)
Used to adjust the output level of the BOOTH MONITOR
terminaL.
Not affected by the master volume and master balance.
~ Effec Selecor Switch (EFFECT SELECTOR)
AUTO BPM (Beat/minute):
Select when performing BPM detection.
DELAY:
Delays the time and repeats once.
ECHO:
Delays the time and repeats several times to produce
echo effects.
AUTO PAN:
Shifts the left and right channels periodically.
FLANGER:
Produces periodië sound change effects by mixing the
short delay sound and original sound.
REVERB:
Produces the reverb effects.
PITCH SHIFTR:
Changes the pitch of the song.
SEND/RETURN:
Select when connecting and using the external effector.
~ Effect Channel Selector (CH. SELECTOR)
Use to select the source to be effected.
~ Parameter Knob (PARAMETER)
Used to adjust the parameter ofthe effector selected with
the effect selector switch.
DELAY:
o to 680 mSec (2 mSec step to 100,5 mSec step from 100
to 680)
ECHO:
o to 680 mSec (2 mSec step to 100,5 mSec step from 100
to 680)
AUTO
PAN:
o to 3500 mSec (5 mSec to 100, 10 mSec from 100 to 900,
20 mSec step from 900 to 3500)
FLANGER:
100 to 9000 mSec (10 mSec to 900, 50 mSec from 900
to 9000)
REVERB:
o to 100% (1% step)
PITCH SHIFTR:
o to :1100% (1% from 0 to 10,2% step from 10 to 100)
~ Effect Switch (EFFECT ON/OFF)
Use to switch the effect on/off.
When turned on according to the beat, the, effects will
also correspond to the beat.
When the effect is on, it goes on and off.