Pioneer DJM-500 Service Manual page 41

CD Main Microphone Terminal and Microphone
Contol Knob
MIC Level:
Used for adjusting t.he volume of the main microphone.
(Attenuated level-. to 0 dB)
HI:
Used for adjusting the high tone of the microphone
sound.
Flat at center click.
Increases when rotated to the right. (To + 12 dB at 10 kHz)
Decreases when rotated to the left. (To -12 dB at 10 kHz)
MID:
Used for adjusting the middle tone of the microphone
sound.
Flat at center click.
Increases when rotated to the right. (To + 12 dB at 1 kHz)
Decreases when rotated to the left. (To -12 dB at 1 kHz)
w:
Used for adjusting the low tone ofthe microphone sound.
Flat at center click.
Increases when rotated to the right. (To + 12 dB at 100 Hz)
Decreases when rotated to the left. (To -12 dB at 100 Hz)
(1 CH1 to CH4 Input Selecon Swich and Contol
Knob/Peak level meter
Input selecion switch:
Selects which sound of the two units connected to each
CH to use.
CHl : Switches between COl/LINE and LINE
CH2 : Switches between CD2/L1NE and PHONO 1
CH3 : Switches between LINE and PHONO 2
CH4: Switches between SUB MIC and PHONO 3
TRIM:
Used for adjusting the level of the input signaL.
The level increases when rotated to the right. (To +6 dB)
The level decreases when rotated to the left. (To-o)
)t~
lJJsed for adjusting the high tone.
"~JFlat at center click.
Increases when rotated to the right. (To + 12 dB at 10 kHz)
Decreases when rotated to the left. (To -20 dB at 10 kHz)
MID:
Used for adjusting the middle tone.
Flat at center click.
Increases when rotated tothe right. (To + 12 dB at 1 kHz)
Decreases when rotated to the left. (To -20 dB at 1 kHz)
LOW:
Used for adjusting the low tone,
Flat at center click.
Increases when rotated to the right. (To + 12 dB at 100 Hz)
Decreases when rotated to the left. (To -20 dB at 100 Hz)
Peak level meter:
Displays the peak level holding it for two seconds.
Displays the level before channel fader,
The display range is -24 dB to + 14 dB,
When BPM is selected using the effect selector and the
effect switch is turned on, the beat monitor function will
be turned on,
o Master Output Monaural/Stereo Selection
Switch (MONO/STEREO)
D.JM-500
o Master level meter (MASTER LEVEL)
Displays the output level after master volume adjusment
while holding it for 2 seconds.
The display range is -24 dB to + 14 dB.
cI Power Supply Switch (POWER)
(§ BPM Display
. When BPM is selected using the effect selector, the BPM
of the source selected with the monitor selector (CH1 to
CH4) will be displayed.
i to 4:
Displays the channel measuring the BPM.
Counter:
Displays the BPM value.
Real-time/average selecion buton and indicator:
(When REAL is seleced.)
The counter displays the measured BPM value.
It will be displayed blinking. If it could not be measured
for more than 5 seconds, U - - -" is displayed.
(When AVERAGE is seleced.)
The display changes when it could be measured.
While measuring, the previous value will remain dis-
played.
. When other than BPM is selected using the effect selec-
tor (DELAY, ECHO, AUTO PAN, FLANGER), the source
BPM selected using the effect channel selector (~) is con-
verted to hours and displayed on the counter.
(j Effecor Parameter /BPM Display
i to 4 MIC MASTER:
Displays the effect source.
Counter:
Displays the effect source BPM and effect parameter, etc.
(Refer to ~ for details of the parameter.)
BPM...375 to 857 mSec (1 mSec step)
70.0 to 160.0 BPM (0.1 BPM step)
BEAT:
When the effect is set to delay, echo, auto pan, or flanger,
displays to which beat the parameter is set. (1/2 to 4 beats)
CI Monitor Selector/Auto BPM Counter Selector
buton (MONITOR SELECTOR/ AUTO BPM COUNTR SE-
LECTOR)
. Selects the source which is monitored using the
headphone (CHl to 4, MIC, MASTER, EFFECT).
When several buttons are pressed, sounds can be mixed.
When the button is pressed another time, the selection
is canceled.
. When BPM is selected using the effect selector, the chan-
nel displaying the BPM (CHl to CH4) is selected.
When more than two are selected together, BPM will not
be displayed properly.
57